Instruction Manual

ManualsBrandsERICO ManualsAccessories for electricalH Series-Electrical Box Bracket

Self tapping screws

Support leg can be

bent in or out.

1. Place box support between electrical box and plaster ring as shown.

2. Attach plaster ring to box as shown.

3. Position offset in box support fully onto edge of stud as shown. Bend

support leg to alternate stud depth as needed.

4. Align notch on box support with box location mark on stud. Mount

assembly to stud using self tapping screw. SMS8 low-profile screw

is recommended.

(Do not feed non-metallic sheathed cables through hole in support leg.)

Model

Number

Description

H23

4" Sq. and 4-11/16" Outlet Boxes to 2-1/2" or

3-5/8" Studs

4" Sq. and 4-11/16" Outlet Boxes to 2-1/2",

3-5/8" or 4" Studs

4" Sq. and 4-11/16" Outlet Boxes to 2-1/2",

3-5/8", 5-1/2" or 6" Studs

TECHNICAL SUPPORT:

www.erico.com

CFS514_B

INSTRUCTION SHEET

1 OF 2

CADDY® H Series

Electrical Box Bracket

WARNING:

ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at

www.erico.com

and from your ERICO customer service representative.

ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and death.

Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.

All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any

other purpose.

NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.

The customer is responsible for:

a. Conformance to all governing codes.

b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified

engineer.

c. Using appropriate industry standard hardware as noted above.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

UL is a registered certification mark of UL LLC

CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.

Summary of content (2 pages)

PAGE 1
INSTRUCTION SHEET CADDY® H Series 1. Place box support between electrical box and plaster ring as shown. 2. Attach plaster ring to box as shown. 3. Position offset in box support fully onto edge of stud as shown. Bend support leg to alternate stud depth as needed. 4. Align notch on box support with box location mark on stud. Mount assembly to stud using self tapping screw. SMS8 low-profile screw is recommended. Electrical Box Bracket (Do not feed non-metallic sheathed cables through hole in support leg.
PAGE 2
INSTRUCTION SHEET CADDY® H Series Electrical Box Bracket Round cutouts for 4-11/16" box Plaster ring low voltage only For use with Canadian boxes Plaster ring low voltage only Hex cutouts are for Standard 4" square box CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. TECHNICAL SUPPORT: www.erico.com CFS514_B 2 OF 2 © 2014 ERICO International Corporation.