Installation guide

Installation clearances:
The location must be large enough to allow the dryer door to open fully.
Most installations require a minimum 51/2"(140 mm) clearance behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
29" Wide Models
Dryer Dimensions
223/4" i
_=/8" I IIIIIF_ t=(578ram) I /
(110=retailII ,3'/8"/
I III-( J I( " 11(-02mm
i
,=0II II k
(660ram} (705mm)._
(737ram)
A
228h,,
(737_m)
228/4"
_8/8,, I _ ..__._._____(578ram) _8/8"i
(1102mm) II_]_ (1102mm)1III/ l_II _8,,,I I1 ',
"273/,"_\ I '-_--'-'--_-JII "273/""'__'II_
1705mm). _r-_. _ (705ram),__,
(737ram) (737ram)
C D
A. Large opening side-swing door
B. Large opening side-swing door
C. Wide opening side-swing door
D. Wide opening hamper door
installation Spacing
ooii
(457 mm_l
_.=_] o/' max,' -
48in_*
_ I_ II;._ mm 310cm)__
[_ 24in.2.-
-.. ._ (155cm)_
1"-_ _- 29"-_ _- 1" -_1"*_ 273_"H5V]'__-
(25ram} (737mm) (25mm)(25mm)(705mrn}(140ram}
A B
E}
C
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
i_ 3"*
(76ram)
-T
(76rnm}
*Required spacing
27" Wide Models
Dryer Dimensions
i 23%"
1t092 ram) (1092mn_)I Ill )JI 13=A"
I Ilk __...J] 1349ram)
i \
(749rnrn} X _--._. -27" -'" (749 ram) \ ,'%F 27" _'"
.- -27"
-_ (687 ram) _="(687 ram}
A B
A. Large opening side-swing door
B. Wide opening hamper door
Installation Spacing
1"-_tI_ 27"_ I<- 1"
(25ram)(686mm)
A
_ 14"max,*
-- _ --_in._
__ (310cm)
__ 24i_*
\I _ k_ (1550m:
(25mm)(25mm)(748mm}(148mm}
B C
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
*Required spacing
_f 3 I1.
-_6 ram)
7
3"*
(76ram)
T
Installation spacing for recessed area or closet
The dimensions shown are for the minimum spacing allowed.
[] Additional spacing should be considered for ease of
installation and servicing.
[] Additional clearances might be required for wall, door, and
floor moldings.
[] Additional spacing of 1" (25 mm) on all sides of the dryer is
recommended to reduce noise transfer.
[] For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
[] Companion appliance spacing should also be considered.
Mobile home-Additional installation requirements
This dryer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280) or the Canadian
Manufactured Home Standard CAN/CSA-Z240 MH.
[] Metal exhaust system hardware, available for purchase.
For further information, please reference the "Assistance or
Service" section of the Use and Care Guide.
[] Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
6