Irideon FPZ User Manual Version 1.0 Part Number: 7191M1200-1.0.
To view a list of ETC trademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. ETC intends this document, whether printed or electronic, to be provided in its entirety.
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications. . . . . . . . . . . . . . . . . . . . . . . 3 Basic Assembly. . . . . . . . . . . . . . . . . . . . . . 4 Installation. . . . . . . . . . . . . . . . . . . . . . . . . 4 Install Track-Mounted Fixture. . . . . . . . . . . . . 4 Install Canopy Fixture (DMX variant) . . . . . . . 5 Install the Voltage Barrier (DMX variant) . . . . . . . . . . . . . . . . . . . . . . . 5 Connect Canopy Wiring (DMX variant) . . .
Adjustments. . . . . . . . . . . . . . . . . . . . . . . 19 Set the Angle with the Yoke . . . . . . . . . . . . . 19 Zoom and Focus the Beam. . . . . . . . . . . . . . . 19 Shape the Beam . . . . . . . . . . . . . . . . . . . . . . . 20 Shape the Beam with Shutters . . . . . . . . . 20 Shape the Beam with a Pattern. . . . . . . . . 20 Rotate the Lens Barrel . . . . . . . . . . . . . . . . . . 21 Use the Integrated Media Holder . . . . . . . . . 21 Install Color Media or Diffusion . . . . . . . .
Introduction The Irideon FPZ takes the beauty and punch of the Source Four Mini beam and puts it into a fixture designed to work in any architectural environment. The Irideon FPZ has three available mounting options: • Track-mount—For use with the DataTrack track system. • Portable—Includes a miniature C-clamp and yoke-mounted driver, and has a permanently installed power cord with 3-prong Edison connector. Region-specific connectors are available. Contact ETC for available options.
WARNING: Please note the following safety warnings before use: • Do not mount the fixture on or near combustible surfaces. • Do not operate the fixture without a lens installed, or with a scratch or cracked lens. Damaged lenses must be replaced. • Use in dry locations only, where humidity does not exceed 90 percent (non-condensing). These fixtures are not intended for outdoor use.
Specifications Physical • Steel yoke with 0.406” (10.3 mm) diameter • Track-mount fixture: - Compatible and ETL-listed for DataTrack mounting hole (EUTRAC) brand track • Rotating shutter assembly ±175° - DataTrack color matching track adapter • E-size gobo pattern holder (included) 1-1/2” included (37.5 mm) with a 1” (25.
Basic Assembly Yoke Pattern holder slot Integrated media holder Shutters x4 Beam zoom and focus knobs (Illustration shows fixture body only) Installation Install TrackMounted Fixture 1: 2: 3: Locking mechanism Insert the DataTrack adapter into the track. The adapter only fits into the track one way with the tabs nesting into the track’s groove. Rotate the locking Circuit mechanisms to lock the selection lock adapter into place. Use the circuit selection lock to select the circuit.
Install Canopy Fixture (DMX variant) Note: The canopy fixture can be installed directly on 4” and 4-11/16” backboxes, or on backboxes with round cover plates. The canopy fixture cannot be installed on 1-gang backboxes or trim rings. Install the Voltage Barrier (DMX variant) The DMX variant of the canopy fixture includes a voltage barrier to separate the data network from the line voltage inside the backbox. Voltage barriers are provided for both 4” and 4-11/16” backboxes.
Connect Canopy Wiring (DMX variant) Cable preparation instructions for DMX termination are included in the termination kits, and are also available for free download at etcconnect.com. 1: Remove the adhesive tape or fasteners securing the mounting plate to the fixture to free the mounting plate from the canopy enclosure.
4: COM Data – (ORG) Data + (W/ORG) BRN GRN W/GRN BLU W/BLU If using Category 5: a: See the Cat5 Cable Preparation for IDC Termination Setup Guide for instructions to prepare and terminate Category 5 for DMX/RDM input cable to the insulation displacement connector. b: Install the IDC connector with wires terminated to the DMX/RDM Input receptacle on the termination board. Optionally, terminate DMX/RDM thru to Cat5 (or equivalent) wire the next device in the DMX data run.
Install the Mounting Plate and Complete the Wiring (DMX variant) Cover plate (if needed for surfacemounting) 1: Mounting plate Secure the mounting plate (or the combination of mounting plate and cover plate for surface-mounting) to the installed backbox, positioning the plate so that the power side and data side are separated by the voltage barrier in the backbox. See Install the Voltage Barrier (DMX variant) on page 5.
2: 5: 6: Use the hook in the canopy enclosure to hang the fixture from the mounting plate while you complete the fixture wiring. Hook 3: If desired, manually set the DMX address on the fixture using the three addressing dials in the canopy. See Set the DMX Address on the Fixture on page 15. 4: Connect the pre-wired DMX connector on the fixture to the mated connector on the mounting plate (shown below).
8: 9: Insert the oval-shaped covers into the canopy enclosure to cover the canopy screw openings. Restore power at the disconnect device. Install Canopy Fixture (0–10 V and DALI variants) Oval-shaped covers Note: The 0–10 V driver conforms to IEC 60929 Annex E. Of the 0–10 V range, use 0–1 V to set the minimum level, and use 1–10 V for continuous dimming. Note: The canopy fixture can be installed directly on 4” and 4-11/16” backboxes, or on backboxes with round cover plates.
Mounting plate (0–10 V and DALI variants) 2 1 3 3 1 2 Canopy screw hole For this structure... 4-11/16” backbox Large oval slots (see 1 above) 4” backbox Small oval slots (see 2 above) Mud ring and round box Circular slots (see 3 above) 3: 4: 5: 6: User Manual ...secure mounting plate using: Use the hook in the canopy enclosure to hang the fixture from the mounting plate while you complete Hook the fixture wiring.
7: 8: Use the canopy screws to secure the fixture to the mounting plate. Insert the oval-shaped covers into the canopy enclosure to cover the canopy screw openings. Canopy screws Oval-shaped covers 9: 12 Restore power at the disconnect device.
Install Portable Fixture with C-clamp The C-clamp attaches the fixture to the mounting pipe and allows you to adjust the position of the fixture once it is mounted. The C-clamp will fit a 3/4” to 2” pipe. Two different length pipe bolts are provided to accommodate different pipe sizes. Note: The miniature C-clamp is available only in non-EU markets. Within the EU, use an M12 bolt to secure a C-clamp (provided separately) to the fixture.
Install Portable Fixture on Unistrut Track You can install the portable fixture on Unistrut track using the Irideon FPZ Unistrut Kit (7191K1000). 1: 2: Insert the spacer into the driver box through the hole in the top of the yoke. Use the yoke bolt and washers to fasten the fixture to the Unistrut track. Within the EU, use an M12 bolt and appropriate washers in place of the provided kit hardware.
Portable Fixture DMX Pinout Pin Wire Color Description 1 White/orange DMX1 + 2 Orange DMX1 - 3 White/green DMX2 + 4 Blue Not Connected 5 White/blue Not Connected 6 Green DMX2 - 7 White/brown Iso Common 8 Brown Iso Common 2 Set the DMX Address on the Fixture You can set the DMX address using RDM, but you can also set the DMX address on the fixture itself, if necessary.
DMX addresses must be set between 1 and 512. Each fixture must be considered a separate DMX device for the purpose of DMX line-loading calculations. The Irideon FPZ only has an intensity channel.
Alternative DMX Addressing Functions Certain DMX addresses are reserved for special functions. Addresses 700 and above can be used for setting the intensity level of the fixture. The second and third address numbers set the intensity level. The intensity knob is ignored when using these DMX addresses.
Initial Power Up Track-Mount, Portable, and Canopy (DMX) Fixtures Control and configure the fixture over a DMX/RDM control network or directly from a connected computer running appropriate software. When controlling the fixture directly from a PC, a Gadget II interface or DMX/RDM gateway is required. Note: Changing the address via RDM will override the local DMX addressing dials.
Adjustments Set the Angle with the Yoke 1: 2: 3: Yoke locking knob Loosen the yoke locking knob. Do not remove the knob. Tilt the fixture to the desired position. Tighten the yoke locking knob to secure the position. Zoom and Focus the Beam 1: 2: 3: Loosen the beam focus or zoom knob located under the barrel. Do not remove either knob. Slide the lens forward or backward to achieve the desired beam edge or angle. Once the fixture is focused, tighten the knobs.
Shape the Beam You can shape the beam using the four shutters or with a pattern. Shape the Beam with Shutters The fixture has four shutters: left, right, top, and bottom. Each shutter can be pulled out or pushed in to create the desired beam shape. Once the shutters are set, you can lock the shutters in place by using a 3 mm Allen wrench (provided). Shutter lock Shape the Beam with a Pattern The fixture has a pattern-holder slot on the top side of the shutter barrel, in front of the shutter.
Rotate the Lens Barrel 1: 2: 3: Unlock the rotating barrel lock using the 2 mm Allen wrench (provided). Rotate the barrel to the desired location. Lock the rotating barrel lock using the 2 mm Allen wrench (provided). Rotating barrel lock Use the Integrated Media Holder The Irideon FPZ comes equipped with an integrated media holder, which is a metal frame used to hold color media (often referred to as gel) or diffusion in front of the lens.
Clean the Lens WARNING: Do not use ammonia-based or other harsh commercial cleaners. Clean lens only as directed. Commercially available glass cleaning agents should be avoided as they may contain ammonia, other harsh chemical detergents, or abrasive agents. These cleaners may damage the lens surface. Do not immerse or soak the lens in any cleaning solution. 1: 2: 3: 4: 5: 6: 7: 8: Remove the integrated media holder. Use a Phillips screwdriver to remove the three screws from the front of the fixture.
Note: You may find it easier to insert the metal shaft into its pocket of each lens before replacing the lens. 9: 10: 11: 12: 13: Replace the lens adjustment knobs. Replace the light block bracket. Make sure that it fits into its pocket of each lens. Replace the metal shaft if you have not previously done so. Replace the front casting and secure it with the screws. Replace the integrated media holder.
Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000 Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535 Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC © 2019 Electronic Theatre Controls, Inc. Product information and specifications subject to change. ETC intends this document to be provided in its entirety. Trademark and patent info: etcconnect.com/ip 7191M1200-1.0.
