User Manual

ManualsBrandsETC ManualsLightingSource Four HID

Source Four™ HID • 1

Source Four

™

HID

Lamp type and general information:

Do not use lamps other than the following lamp type in Source Four HID ﬁxtures.

Use of lamps other

than speciﬁed below will void UL/cUL safety compliance and your warranty

•

Source Four HID is suitable for damp locations

•

Can be canopy mounted

•

No recessed mounting

Caution!

Source Four HID is

NOT

dimmable. Dimming will damage ballast and void warranty.

Ballast information

Caution!

The Source Four HID

cannot

be dimmed.

•

Acceptable voltage is 120V (+/- 10%) 50/60HZ

only

•

Operating current of 1.5 Amps

•

Inrush current of <14 Amps

•

Room ambient temperature should not exceed 104ºF (40ºC)

•

Lamp ignition voltage is 4.5Kv, non-hot restrike.

•

Ballast case temperature should not exceed 167ºF (75ºC)

•

The ballast is attached to the Source Four yoke by two screws, non-remotable.

Lamp Type Manufacturing Codes Watts Base Bulb LCL Ave.

Hrs.

Initial

lumens

Color

temp

Ceramic Metal Halide

CDM-T 150W/830 150 G12 T6 56mm 9000 14000 3000˚K

CDM-T 150W/942 150 G12 T6 56mm 9000 12700 4000˚K

MD150T6/U/G12/830 150 G12 T6 56mm 9000 14000 3000˚K

MBI150/T/30 150 G12 T7 57mm 6000 11500 3000˚K

MBI150/T/40 150 G12 T7 57mm 6000 11250 4000˚K

Table 1:

HID lamp reference

Beam focus knob

Lens tube

Shutters

Barrel

Pattern holder slot

Retainer bolt

Drop-in iris

Retaining clip

Color frame

Color frame holder

Reﬂector housing

Yoke locking knob

Lamp housing

Ballast

Barrel rotation knob

Yo ke

Summary of content (8 pages)

PAGE 1
™ Source Four HID Lamp housing Ballast Yoke Reflector housing Retainer bolt Shutters Pattern holder slot Drop-in iris Yoke locking knob Color frame Barrel rotation knob Retaining clip Barrel Color frame holder Beam focus knob Lens tube Lamp type and general information: Do not use lamps other than the following lamp type in Source Four HID fixtures. Use of lamps other than specified below will void UL/cUL safety compliance and your warranty.
PAGE 2
Installing or replacing the lamp A lamp must be installed before you use the fixture. HID Lamp Note: Verify that the lamp you intend to install is correct. Replace the lamp if it becomes damaged or thermally deformed. Lamp base WARNING! Let the lamp cool before replacing. 1. Disconnect power to the Source Four HID before installing the lamp. 2. Loosen the knurled bolt on the back of the lamp housing and pull the housing out. 3. Holding it by the base, remove the lamp from its box.
PAGE 3
Color frame retaining clip Retaining clip in the locked position The color frame holder is equipped with a spring-loaded retaining clip that prevents color frames and accessories from falling out (Figure 3). WARNING! Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four HID. 1. Release the retaining clip by pushing it sideways while gently pulling backwards. Figure 3 2. Insert the color frame. 3.
PAGE 4
Rotating the barrel assembly 1. Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector housing (Figure 6). Do not remove the barrel rotation knob. 2. Rotate the barrel to the desired position (up to 25° in either direction from the centered position). 3. Once the barrel is positioned, tighten the barrel's rotation knob to lock it into position.
PAGE 5
Cleaning ETC offers the following recommendations when cleaning and inspecting lenses and reflectors: Do not use glass or window type cleaners on lenses (glass or polymer) or reflectors. Do not use abrasive materials such as steel wool. Replace lenses if they contain visible damage (cracks or deep scratches) that may impair their effectiveness. Cleaning 19°, 26°, 36°, and 50° glass lenses 1. Remove the beam focus knob at the bottom of the barrel. Remove the lens tube from the barrel.
PAGE 6
Cleaning the reflector WARNING! Disconnect the power to the fixture before attempting to clean the reflector. To quickly clean the reflector, remove the lens tube and clean the dust from the reflector with a blast of oil-free air. You may also wipe the reflector with a clean lint-free cloth. If either method is not sufficient, follow the instructions below. You will need a Phillips screwdriver to complete this procedure. 1. Remove the barrel rotation knob located at the bottom of the barrel.
PAGE 7
Source Four™ HID • 7
PAGE 8
Electronic Theatre Controls North America 3030 Laura Lane • Middleton, Wisconsin 53562 • USA • Tel: (+1) 608 831 4116 • Fax: (+1) 608 836 1736 Europe 5 Victoria Industrial Estate • Victoria Road • London W3 6UU • Tel: (+44) 181 896 1000 • Fax: (+44) 181 896 2000 Asia Room 605-606 • Tower III • Enterprise Square • 9 Sheung Yuet Road • Kowloon Bay • Hong Kong • Tel: (+852) 2799 1220 • Fax: (+852) 2799 9325 World Wide Web: http://www.etcconnect.com • Email: mail@etcconnect.com Specifications subject to change.