User Manual

ManualsBrandsEuro Communication Equipement ManualsElectronicsBluetooth Handsfree Car Kit

User Guide

Supertooth II

Universal Bluetooth Handsfree Kit with DSP

Contents

____________________________________________________________

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switching On/Off. . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Pairing to a Mobile Phone . . . . . . . . . . . . . . . . . . . . . . .3

Indicator Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Hands-free Profile . . . . . . . . . . . . . . . . . . . . . . . . . . .4

SuperTooth II Operations. . . . . . . . . . . . . . . . . . . . . .4

Button Functions Matrix . . . . . . . . . . . . . . . . . . . . . .5

Headset Profile. . . . . . . . . . . . . . . . . . . . . . . . . .6

SuperTooth II Operations. . . . . . . . . . . . . . . . . . . . . .6

Button Functions Matrix . . . . . . . . . . . . . . . . . . . . . .7

SuperTooth II is equipped with Bluetooth and Digital Signal Processor

which allow wireless communications on devices such as cellular phones.

This is designed to be a totally portable wireless handsfree kit which will

enable the user to communicate freely without holding the phone. This will

work on any Bluetooth cellular phones available provided that they respect

the Bluetooth protocol.

1 Swivel Arm

2 Reject Button

3 Headphone Jack

4 Speaker

5 Charger Input

6 Accept / End Button

7 Microphone

8 Bluetooth Indicator

9 Charge Indicator

10 Volume Control

A. PRODUCT OVERVIEW

Summary of content (7 pages)

PAGE 1
User Guide Supertooth II Universal Bluetooth Handsfree Kit with DSP Contents ____________________________________________________________ Product Overview . . . . . . Switching On/Off. . . . . . . Charging . . . . . . . . . . . Installation. . . . . . . . . . Pairing to a Mobile Phone . . Indicator Status. . . . . . . . Hands-free Profile . . . . . . SuperTooth II Operations. Button Functions Matrix . Headset Profile. . . . . SuperTooth II Operations. Button Functions Matrix . . . . . . . . . . . . . .
PAGE 2
B. SWITCHING ON/OFF Note: The Swivel Arm[1] can be adjusted to 0º , 55º and 210º orientations. Power on: Flip up the Swivel Arm [1] from 0º to 55º to 210º positions. The Bluetooth indicator[8] will glow (blue blink). This indicates that the kit is ready (standby mode). Note: At first use, the user has to pair SuperTooth II with his phone (refer to Section E PAIRING TO A MOBILE PHONE.) Power off: Flip down the Swivel Arm to 0º position. The Bluetooth Indicator will become red then turns off after a second.
PAGE 3
E. PAIRING TO A MOBILE PHONE (not possible while charging the SuperTooth II) Pairing will create a link or connection between the two Bluetooth devices, the SuperTooth II and your phone. 1. Bring the mobile phone at about 20cm from the SuperTooth II. 2. The SuperTooth II is initially off; Turn it on by flipping up the Swivel Arm[1] to 55º position. The Bluetooth Indicator[8] will glow (blue blink). 3. Simultaneously press the Reject Button[2] and Accept/End Button[6] for about 5 seconds.
PAGE 4
F. Indicator Status STATUS Bluetooth Indicator [8] Pairing Mode Standby mode On Call Low Batt Charging Fully Charged Ringing Alternate Blinking - Red / Blue Blinking Blue Steady Blue Charge Indicator [9] Blinking Red Alternate Red / Green Steady Green Fast Blinking Blue G. HANDS-FREE PROFILE Supertooth II OPERATIONS Make a Call (Normal dial): Dial the number using your phone. Normally, audio will be on the SuperTooth II.
PAGE 5
Answer a Call: When the phone receives a call, ring tone will be on the SuperTooth II alone, or both on the SuperTooth II and on the phone (depending on your phone model). Just short press Accept/End Button[6] to answer the call. Reject a Call: Short press Reject Button[2] to reject an incoming call. Set the Volume: Set the volume using the Volume Control[10]. 1. Turn it clockwise to increase the volume. 2. Turn it counterclockwise to decrease.
PAGE 6
I. HEADSET PROFILE Supertooth II OPERATIONS Make a Call (Normal dial): Dial the number using your phone. Normally, audio will be on the kit. Note: With some phones like Siemens S55; Panasonic X70, audio is always on the phone during an outgoing call. You will need to short press Accept / End Button[6] to transfer the audio to your kit. Make a Call (Voice dial): 1. First, you have to access the voice dialing function of your phone, turn it on and record for a voice tag.
PAGE 7
Audio Transfer : from Phone to SuperTooth II (SuperTooth II initiated): Short press the Accept/ End Button[6]. J.