Tone Tracer, High-sensitivity User's Guide www.jdsu.
Battery Low Volume (on side) Tip Change Screw (on bottom) “ON” Button Battery Door Screw (on bottom) Lanyard Loop Headset Jack
Warning! Do not touch to live AC circuits. This could cause an extreme shock hazard and damage the TT100.
Instructions for Use To trace a tone 1) C onnect an audio frequency tone generator, such as the TG100, to cable to be traced. Application Hints When tracing wires terminated to a terminal block such as a “66 block”, attaching both generator leads to the cable or pair tends to contain the signal within the cable. The tracer must nearly touch the end of the cable to detect the signal, which is helpful when the wires are close together, as when terminated.
2) P ress the recessed black button to turn on the TT100. The power is on only as long as the button is being pressed. The battery low LED flashing on during turn on and turn off is normal. 3) Adjust volume to a comfortable level. If the signal is very loud when near the cable, the volume may need to be reduced to keep from overloading the TT100. When overloaded, small increases or decreases in the signal at the tip cannot be heard. 4) H old tip of TT100 near cables to be identified.
To Change the TIP 1) R emove screw nearest to the tip on the back of the TT100 with a #1 Philips screwdriver. 2) Pull the tip out of the front. 3) Push new tip into front. 4) R eplace screw and tighten (about 4 inlbs), being careful not to over tighten. Battery Replacement When the battery low LED is on continuously whenever the “on” button is being pressed, replace the battery. 1) R emove screw at the back of the TT100 with a #1 Phillips screwdriver. Remove battery door.
Models, options & accessories Order number Description TT100 Tone Tracer TT35 Replacement paddle style tip for probes TT30 Replacement round tip for probe LB40B Headset with boom microphone, mini over-the-ear, 2.5mm jack LB45B Headset with cushioned ear piece, full over-the-head, 2.
KP104 Turbo-Tone high power tone generator with angled bed-ofnails clips TG201 and probe TT100 kit in a nylon pouch KP105 Turbo-Tone high power tone generator with alligator clips TG200 and probe TT100 kit in a nylon pouch KP106 Latch-Test security/alarm tone generator with alligator clips TG300 & probe TT100 in a nylon pouch KP300 Lil’ Buttie telephone test set with angled bed-of-nails clips LB110, tone generator with alligator clips TG100 & probe TT100 probe in a nylon pouch KP400 Lil’ Buttie Pro
Customer Services This section provides a description of customer services available through JDSU (including returns policies and procedures) and warranty information. Customer Service (Standard Services) Customer Service accompanies the sale of every JDSU product.
manufactured equipment. This ensures products meet all published specifications, including any applicable product updates. Calibration — JDSU’s calibration methods are ISO approved and based on national standards. Factory Upgrades — Any unit returned for a hardware feature enhancement will also receive applicable product updates and will be thoroughly tested, ensuring peak performance of the complete feature set.
problem or service requested. The name and telephone number of the person to contact regarding questions about the repair. • The return authorization (RA) number (US customers), or reference number (European Customers). If possible, return the equipment using the original shipping container and material.
Warranty Information JDSU guarantees that its products will be free of all defects in material and workmanship. This warranty extends for the period of 12 months for test instruments and 3 months for cables from date of manufacture or purchase (proof of purchase required). All product deemed defective under this warranty will be repaired or replaced at JDSU’s discretion. No further warranties either implied or expressed will apply, nor will responsibility for operation of this device be assumed by JDSU.
is reused, recycled, or disposed of in an environmentally friendly manner, and in compliance with all applicable national and international waste legislation. It is the responsibility of the equipment owner to return the equipment to JDSU for appropriate disposal. If the equipment was imported by a reseller whose name or logo is marked on the equipment, then the owner should return the equipment directly to the reseller.
www.jdsu.com/know Document Information Doc.
