EHD930 eZ.HD Series 720p Analog High Definition True Day/Night Outdoor IR Dome Vandal Camera User’s Manual Copyright © EverFocus Electronics Corp, Release Date: Nov.
Precautions 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere with camera operation. 2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein.
Safety Notice Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Contents 1. Introduction...................................................................................................................... 5 1.1 1.2 Packing List ..................................................................................................................... 5 Features .......................................................................................................................... 5 2. Cable Description ...................................................................
EHD930 eZ.HD Vandal Dome Camera 1. Introduction Get incredible performance in bright light or low light environments, and the resolution listed in the specification from the actual camera you install. To take full advantage of the amazing resolution available from this advanced imaging technology, the EverFocus eZ.HD Series EHD930 uses a vari-focal lens together with 1/2.8" SONY 1.37M pixels CMOS to deliver 720p high resolution. Combined with a useable native low light sensitivity of 0.
EHD930 eZ.HD Vandal Dome Camera Provides 3D Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio images even under low light environment Support 720p & 960H analog signal output, which can be easily switched by OSD Convenient speedy-mount base plate easily attaches to surface, camera attaches to plate with machine screw 2. Cable Description No. Name Descriptions 1 Power Cable Connect to a 12VDC or 24VAC power source.
EHD930 eZ.HD Vandal Dome Camera 3. Installation 3.1 Installation and Adjustment 1. To remove the Cover Cap, unscrew the three Set Screws using the supplied Hexagon Wrench. 2. For Ceiling Mount / Wall Mount users: Stick the Template Plate on the position where you want to attach the camera, drill the four holes on the Template Plate for screwing the Adapter Plate with the supplied Screws and Anchors.
EHD930 eZ.HD Vandal Dome Camera 3. To screw the camera onto a Wiring Box or using a Bracket: a. You can optionally screw the camera to the wall using an L-Shaped Mounting Bracket. b. Screw the supplied Adapter Plate to the Wiring Box or the L-Shaped Mounting Bracket using the screw holes on the Adapter Plate. Note the holes A / B are designed for screwing the camera / L-Shaped Mounting Bracket. 4. If you want to wire the cable through the side of the camera, follow the steps below: a.
EHD930 eZ.HD Vandal Dome Camera 5. Screw the camera to the Adapter Plate. 6. Connect the camera to a AHD DVR or a portable monitor with the 12VDC or 24VAC power source using the supplied DC power pigtail cable or a power adapter. 7. Using the Test Lead for viewing the video image while adjusting camera angles. You can also use the OSD Menu Joystick to configure camera settings. a. Adjust camera angles by tilting or rotating the camera.
EHD930 eZ.HD Vandal Dome Camera b. Configure the camera settings using the OSD Menu Joystick, connect one end of the Test Lead to the Test-Out connector on the camera module and the other end to the portable monitor. Push the Joystick up / down to select among menu items. Push the Joystick left / right to adjust the level of the selected item. Press the Joystick to enter the submenu or exit the OSD Setup Menu.
EHD930 eZ.HD Vandal Dome Camera 9. Tear apart the outer packing ( figure 1 ) to take out the Desiccant Bag ( figure 2 ), then make it folded ( figure 3 ) and put it into the camera housing ( figure 4 ). Note: It’s recommended to close the cover cap immediately in case of reducing the absorption capacity of the desiccant bag inside the camera. 10. Screw back the Cover Cap Set Screw using the supplied Hexagon Wrench.
EHD930 eZ.HD Vandal Dome Camera 4. Configuration in the OSD Menu You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD menu. For details on the OSD menu structure as below: No. Main Sub Menu Sub Menu / Function Indoor Min Shu. 1 Lens DC* Mode Outdoor* Max. Shu.
EHD930 eZ.
EHD930 eZ.HD Vandal Dome Camera Select Display On Area1*,Area2,Area3,Area4 On* Position, Size,↑,↓,→,← Off Sensitivity 0-100(64*) Color Green*, Blue, White, Red Trans 1.00*,0.75,0.50, 0.
EHD930 eZ.HD Vandal Dome Camera On RS485 Pos/Siz Position, Size,↑,↓,→,← Start Press Enter DPC View Off*/On Level 0-255(255*) CAM ID 0-255(1*) ID Display Off*/On Baud Rate 2400,4800,9600,19200 ,38400 Off Sharpness Auto* CRT 8 Level 0-10(6*) Start AGC 0-255(50*) End AGC 0-255(200*) Black Level 0-60(0*) Blue Gain 0-100(50*) Red Gain 0-255(50*) Gamma User*,0.45,0.50,0.55,0.60, 0.65,0.70,0.75,0.80,0.85,0. 90, 0.95,1.
EHD930 eZ.HD Vandal Dome Camera 5. Specifications P/N Pickup Device Video Format Effective Pixels Scanning System Sensitivity S/N Ratio Electronic Shutter Video Output Gamma Correction Lens Type BLC AGC White Balance Sync Mode Day/Night IR LED IR Distance OSD Languages DNR DEFOG D-WDR Sens-up Mirror Motion Detection Privacy Mask Environmental Power Source Power Source Operating Temperature Humidity Dimensions Weight Certifications EHD930 1/2.8" SONY 1.
EHD930 eZ.HD Vandal Dome Camera EverFocus Electronics Corp. EverFocus Taiwan: 12F-1, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, New Taipei City, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 3943 www.everfocus.com.tw marketing@everfocus.com.tw EverFocus Europe - Germany: Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de sales@everfocus.
