Datasheet

ManualsBrandsEVERLIGHT OPTO ManualsPhotodiodes & PhototransistorsPhotodiode 1206 1200 nm

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 1 of 10

Device No

DTD-152-139 Prepared date 02-15-2008 Prepared by Jaine tsai

Technical Data Sheet

1206 Package Silicin PIN Photodiode

PD15-21B/TR8

Features

․Fast response time

․High photo sensitivity

․Small junction capacitance

․Package in 8mm tape in “7” diameter reel

․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

․PD15-21B/TR8 is a high speed and high sensitive

PIN photodiode in miniature flat top view lens

SMD package and it is molded in a black plastic.

The device is Spectrally matched to infrared emitting

diode.

Applications

․High speed photo detector

․Copier

․Game machine

Device Selection Guide

Chip

LED Part No.

Material

Lens Color

PD15-21B/TR8 Silicon Black

Summary of content (10 pages)

PAGE 1
Technical Data Sheet 1206 Package Silicin PIN Photodiode PD15-21B/TR8 Features ․Fast response time ․High photo sensitivity ․Small junction capacitance ․Package in 8mm tape in “7” diameter reel ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․PD15-21B/TR8 is a high speed and high sensitive PIN photodiode in miniature flat top view lens SMD package and it is molded in a black plastic. The device is Spectrally matched to infrared emitting diode.
PAGE 2
PD15-21B/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃ ℃) Parameter Symbol Rating Reverse Voltage VR 32 Units V Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ *1 Tsol 260 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pc 150 mW Soldering Temperature Notes: *1:Soldering time≦5 seconds. Everlight Electronics Co., Ltd. Device No ：DTD-152-139 http://www.
PAGE 3
PD15-21B/TR8 Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Symbol Condition Min Typ Max Unit Rang Of Spectral Bandwidth λ0.5 --- 730 --- 1100 nm Wavelength Of Peak Sensitivity λP --- --- 940 --- nm Open-Circuit Voltage VOC Ee=5mW /cm2 λP=940nm --- 0.42 --- V Short-Circuit Current ISC Ee=1mW /cm2 λP=875nm --- 0.8 --- μA Reverse Light Current IL Ee=1mW /cm2 λP=875nm VR=5V 0.2 0.
PAGE 4
PD15-21B/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Power Dissipation vs. Ambient Temperature Fig.2 Spectral Sensitivity 1.0 200 Ta=25 C 0.8 150 0.6 100 0.4 50 0.2 0 -25 0 25 50 75 85 100 Fig.3 Dark Current vs. Ambient Temperature 0 700 800 900 1000 1100 1300 Fig.4 Reverse Light Current vs. Ee 1000 2.0 1.5 100 1.0 10 0.5 VR=5V VR=10V 1 20 40 60 80 100 0 0.5 1.5 1.0 3.0 2 Everlight Electronics Co., Ltd. Device No ：DTD-152-139 http://www.everlight.
PAGE 5
PD15-21B/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Fig.6 Response Time vs. Reverse Voltage t 10 Load Resistance f=1MHZ VR=5V 10 1 VR=10V Ta=25°C 2 0 8 10 6 10 4 10 -1 -2 -3 10 2 0.1 1 Everlight Electronics Co., Ltd. Device No ：DTD-152-139 10 100 10 http://www.everlight.
PAGE 6
PD15-21B/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.
PAGE 7
PD15-21B/TR8 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal.
PAGE 8
PD15-21B/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item Test Conditions Test Hours/ Sample Failure Cycles Sizes Ac/Re Judgement Criteria 1 REFLOW Soldering TEMP.：260℃±5℃ 10secs 2 Temperature Cycle H : +100℃ 3 Thermal Shock 4 High Temperature 6Mins 22pcs 0/1 IL≦L×0.
PAGE 9
PD15-21B/TR8 Package Dimensions 1. Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel) Anode Cathode Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No ：DTD-152-139 http://www.everlight.
PAGE 10
PD15-21B/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity RoHS CAT: Ranks PD15-21B/TR8 HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2.