Instructions / Assembly

10
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [e-mail]
Parts List
Qty Grill Assembly Components
1 Right Front Leg
1 Left Front Leg
1 Rear Leg
2 Leg Supports
( LP Only )
1 Removable Leg Support ( LP Only )
3 Leg Supports ( Natural Gas Only )
1 Lower Rack
1 Drip Pan
1 Waste Tray
1 Regulator / Hose Assembly
( LP Only )
1 Natural Gas Quick-Disconnect Hose
( Natural Gas Only )
Parts Box
1 Fastener Package
1 Right Wheel Spacer
1 Left Wheel Spacer
2 Wheel
2 Spanner Bushing
2 Wheel Hub Plate
1 Hood Handle
1 Hood Support
1 Rear Grill Handle
2 Hose Clamp and Fasteners
( Natural Gas Only )
1 Electronic Ignitor Battery (AA or AAA)
Tools Included
1 Socket and “L” Handle
1 7/16” Open-End Box Wrench
Tools Required
1 Phillips Screwdriver
1 Hammer
1 Small Block of Wood (Approx. 2” x 4” )
Literature Bag
1 Install Instructions & Owners Manual
1 Use & Care Manual
Qty Key Legs to Lower Rack
6 10 1/4” - 20 x 1/2” Phillips Screw - Stainless Steel
6 11 1/4” - 20 Nyloc Nut - Stainless Steel
Wheels to Lower Rack
2 20 3/8” x 7/8” - Flat Washer - Stainless Steel
2 21 3/8” Nyloc Hex Nut - Stainless Steel
6 22 8 x 3/8” Phillips Screw - Stainless Steel
Leg Supports to Leg Frame
8 30 1/4” - 20 x 1/2” Phillips Screw - Stainless Steel.
Note: On LP models, 8 screws connect two leg supports.
The third removable key-way leg support uses pre-installed
hardware.
12 30 1/4” - 20 x 1/2” Phillips Screw - Stainless Steel.
Note: On Natural Gas models, 12 screws are required for
connecting all three leg supports to leg frame. Removable
leg support not used on Natural Gas models.
8 31 1/4” - 20 Nyloc Nut - Stainless Steel.
Note: On LP models, 8 nyloc nuts are required for connect-
ing all two leg supports to leg frame. The third (right-most
from front of grill) is a removable (keyed) support.
12 31 1/4” - 20 Nyloc Hex Nut - Stainless Steel.
Note: On Natural Gas models, 12 nyloc nuts are required
for connecting all three leg supports to leg frame.
Leg Frame Assembly to Burner Unit
6 40 1/4” - 20 x 1/2” Phillips Screw - Stainless Steel
6 41 1/4” - 20 Nyloc Hex Nut - Stainless Steel
Drip Pan to Burner Unit
3 50 1/4” - 20 x 1/2” Phillips Screw - Stainless Steel
3 51 1/4” - 20 Nyloc Hex Nut - Stainless Steel
Rear Handle to Burner Unit
2 60 1/4” - 20 x 1/2” Phillips Screw - Stainless Steel
2 61 1/4” - 20 Nyloc Hex Nut - Stainless Steel
Hood Handle and Hood Support
2 70 1/4” - 20 x 5/8” Phillips Screw - Stainless Steel
2 71 1/4” Lock Washer
2 72 1/4” - 20 Hex Nut
Natural Gas Hose to Rear Leg
( Natural Gas Only )
2 100 5/8” Stainless Steel Hose Clamps
Screw / Nut Combination Included
You may have extra hardware after completing as-
sembly of your grill. This is normal, as in some cases
we have included extra hardware to ensure you have
enough.
Fastener Package Listed in Order of Assembly Group