User Guide

ManualsBrandsExtang ManualsAutomotiveExtang Encore Soft Folding Truck Bed Tonneau Cover | 62590 | fits Honda Ridgeline 2017-18, no BOLT - incl. 2 keys

MISSING PARTS?

call Extang at

1-800-877-2588

Any and all needed parts will be

shipped to you directly.

(DO NOT return whole kit to store)

Extang Corporation

5400 S. State Road

Ann Arbor, MI 48108

734 677-0444, Fax: 734 677-8409

extang.com

Item No. 62000-30-1606 RH

©Extang Corp., 2016 Printed in U.S.A.

If your Truck has a Bed Liner or Rail Caps

Apply foam seal (included) to

front lip of truck bed (below

cab rear window) from driver

side bed rail cap to

passenger side rail cap.

If cab is higher than side rails (liner) either...

Use a credit card or straight edge to see if there is more than a 1/8”

gap between your liner and the sheet metal.

... trim off bed overlap,

or...

... add bed rail caps

designed for your vehicle.

If there is a gap between the cab

rail liner and the side rail caps, cut

a small piece of adhesive foam seal

and insert.

If side rails are higher than cab rail…

Side Rail

Cap

Liner

Do Not apply foam

seal if not required.

• 1/2” Socket Wrench

• 3/4” Sheetmetal Drill Bit

• #2 Phillips Screwdriver

Sheet

Metal

Sheet

Metal

1/8”

Liner

Summary of content (10 pages)

PAGE 1
MISSING PARTS? call Extang at 1-800-877-2588 Any and all needed parts will be shipped to you directly. (DO NOT return whole kit to store) • 1/2” Socket Wrench • 3/4” Sheetmetal Drill Bit • #2 Phillips Screwdriver 1 If your Truck has a Bed Liner or Rail Caps Use a credit card or straight edge to see if there is more than a 1/8” gap between your liner and the sheet metal. If cab is higher than side rails (liner) either... 1/8” Liner Sheet Metal ... trim off bed overlap, or... ...
PAGE 2
1 Position Drain Rail Place drain rail assembly on truck bed wall and position toward the front of the bed using the spacer block provided (all models except Nissan Frontier 62985, 62995). Note: please see special clamp supplement for steps 2 and 3 for the 2016 Nissan Titan. . A spacer block is included to ensure proper installation. Slide drain rail assembly forward until spacer block touches cab bulkhead. Insert spacer block and rotate down against the first drain rail stud.
PAGE 3
5 1 Code Tonneau Lock to your Vehicle Key! NOTE: Your tonneau lock can only be coded ONE TIME. Key code your lock cylinder per these instructions. You will need your vehicle key to complete this step. 1. Remove protective label, and remove vehicle key from keychain. 2. Fully insert the key into the lock cylinder before starting to rotate key. 1. NOTE: Do not pull left/right on key. 3. While maintaining FULL key insertion, rotate key clockwise until it hits a stop point (approximately 3/4 of a turn).
PAGE 4
9 Unfold front panel and position cab and middle panels over truck bed making sure retaining hooks engage pins in drain rail. Press down on cab panel to lock in place 10 With tailgate open, unfold tail panel and press down onto truck bed. Tonneau should now be secure. Before this step, be sure you UNLOCK the panel latch. NOTE: To insure a better seal, always close panel before closing tailgate.
PAGE 5
Rail Reference Sheet Spacer Seal and Shim Placement I M P O R TA N T Your EnCore side rails have had either a spacer seal or shims attached to provide for easy installation. The spacer or shims help provide a level sitting rail to enable secure tonneau latching. Please refer to images below and the guide on the following page per application or vehicle type to confirm the correct application of the seals or shims.
PAGE 6
Rail Reference Sheet Spacer Seal and Shim Placement SHIM LOCATIONS 2015+ Colorado 62350 62355 2014+ Silverado/Sierra 62445 62450 62455 2015+ 2005+ F-150 Frontier 62475 62480 62485 62985 62995 Drivers Side Rail Shown Extang Corporation, 5400 S. State Road, Ann Arbor, MI 48108, 734 677-0444, Fax: 734 677-8409 Visit us at: extang.
PAGE 7
IMPORTANT! EnCore Tonneau Cover — Safe Operation and Use Tonneau Cover Positions While Operating Vehicle Prior to vehicle operation, tonneau cover MUST be properly secured. CLOSED POSITION • Front panel must be closed and FULLY LATCHED to tonneau side rail. Center and rear panel must be flat and rear latches engaged. • Verify front panel is securely attached on both sides of truck before operating vehicle. OPEN POSITION • Tonneau must be folded to cab position and secure with BOTH buckles.
PAGE 8
Replacement Parts NOTE: To order replacement parts itʼs best to contact our Customer Service Department for assistance to ensure getting the correct part for your vehicle application. When ordering, please provide the 5-digit product number as referenced on your sales receipt or product identification sticker on your tonno cover (example: 62790).
PAGE 9
READ CAREFULLY - KEEP IN A SAFE PLACE PLEASE ATTACH AND SAVE YOUR SALES RECEIPT. ACTIVATE YOUR wARRANTY ONLINE AT ExTANg.COm. EXTANG LIMITED WARRANTY ■ WARRANTY DURATION: Extang offers three years of coverage from the date of purchase. Warranty is limited to original purchaser of truck bed cover and is non transferable. ■ WARRANTY CONDITIONS: This warranty is against defective materials or workmanship.
PAGE 10
SOMETHING DAMAGED? MISSING PARTS? CALL US FIRST 800-877-2588 WE CAN HELP YOU QUICKLY AND EASILY OVER THE PHONE RAPID RESPONSE Lot code can be found on underside of cover. Lot Code:______________________________________ Purchase Date:_________________________________ Tonno Model: __________________________________ OVERNIGHT DELIVERY Experienced Customer Service staff to answer all your tonneau questions CUSTOMER SERVICE HOURS: 8:30 TO 5 EST, MONDAY - FRIDAY Printed in U.S.A.