Quick Reference Guide

ManualsBrandsExtreme Networks ManualsComputers & Accessories24-port 10 Gigabit Aggregation and Leaf Switch

X590 Series Switch Quick

Reference

Follow these steps to get your switch up and running.

For complete installation instructions see the ExtremeSwitching and

Summit Switches: Hardware Installation Guide at

www.extremenetworks.com/documentation

Tools You’ll Need

• Appropriate grounded power receptacles

located within 1.8 m (6 ft.)

• A readily accessible device for disconnecting

power, such as a breaker or master switch

• Network cabling within reach

• At least of 7.6 cm (3.0 in.) on all sides, for

proper ventilation

• Temperature between 0°C (32°F) and 45°C

(113°F) with fluctuations of less than 10°C

(18°F) per hour

If the switch appears to be damaged, contact Extreme Networks. See

“Getting Help” for more information.

Extreme Networks does not include power input cords with this product.

To purchase the correct power cord for your country, refer to

www.extremenetworks.com/product/powercords/. This page lists

details for purchasing a power cord from Extreme Networks or from

your local supplier.

1 #2 Phillips screwdriver

(magnetic screwdriver recommended)

3 Rack-mounting screws

2 Flat-head screwdriver 4 ESD-protective wrist strap

Prepare the Site

The installation site must meet the following requirements:

Unpack the Box

Remove the packing material. Break the tape seal on the

non-conductive bag and remove the switch.

1 Switch (48-port model shown) 3 Bracket screws

2 Mounting brackets

There are four ways to mount the X590 Series switch in a rack:

• Either the I/O ports or the power-supply side can face front.

• The switch can be mounted flush with the rack posts or mid-

mounted.

Note: The following diagrams show a mid-mounted configuration. Other

options are shown in the Hardware Installation Guide.

1 Attach the mounting brackets to the sides of the switch using six

screws (included) for each bracket.

2 Align the holes in the brackets with the rack post holes.

3 Secure the switch to each post with fasteners appropriate to the rack.

1 Attach the ESD wrist strap to your wrist and connect the metal end

to an appropriate ground point on the rack.

2 Remove the transceiver from its packaging.

3 If applicable, remove the protective dust cover from the connector.

4 Hold the transceiver so that the connector will seat properly.

5 Carefully align the transceiver with the port slot.

6 Push the transceiver into the port slot until it clicks into place.

Install the Switch

You can install any X590 Series switch in a standard 19-inch

equipment rack.

Install Transceivers

(Optional) Transceivers can send and receive data over

optical fiber rather than through electrical wires. This

installation procedure applies to all transceivers.

Note: Transceivers are Class 1 or Class 1M laser devices.

Connecting to the Primary Power Source

To attach your X590 Series switch to a power source, do the following:

1 Connect the AC power cord to the AC power input socket on the

power supply and an AC power outlet.

2 For DC powered supplies, verify that the DC circuit is de-energized

and then do the following:

a Identify the grounding stud on the DC power supply. The grounding

stud is next to the DC input connector, identified by the international

symbol for earth ground.

b Using the nut and washer provided, connect the ring terminal end of

the ground wire to the grounding stud on the DC power supply.

Use green and yellow stranded copper wire, sized at least 14 AWG.

c Connect the other end of the ground wire to a reliable earth ground.

d Connect the DC power input cables to the DC input connector

provided.

Use copper wires rated for at least 60°C and sized between 14 AWG

and 8 AWG.

e Energize the circuit.

3 When power is connected, verify that the switch’s PWR LED turns

green. If the PWR LED does not turn green, refer to the Hardware

Installation Guide for troubleshooting information.

Safety Notices

Connect Power

X590 Series switches can run on AC or DC power. Connect

the switch to a primary power source.

Note: Installing the system as described in this guide meets the

protective earth grounding requirements of the National Electrical

Code (NEC), UL/CSA/IEC/EN 60950-1 standards. However, in some

cases, it may be necessary to use an alternative grounding method.

In these cases, a 14 AWG wire can be connected between the

grounding lug on the chassis and a nearby building ground point.

Configure the Switch

To connect the switch to the network and configure it for

use, follow the steps in www.extrconfig.com/exos.

Electrical Hazard: Only qualified personnel should perform

installation procedures.

Risques d’électrocution: Seul un personnel qualifié doit effectuer

les procédures d'installation.

Warning: Extreme Networks power supplies do not have switches for turning

the unit on and off. Before servicing, disconnect all power cords to remove

power from the device. Make sure that these connections are easily accessible.

Avertissement: Extreme Networks alimentations ne sont pas des interrupteurs

pour allumer l'appareil et en dehors. Avant l'entretien, débranchez tous les

cordons d'alimentation pour couper l'alimentation de l'appareil. Assurez-vous

que ces connexions sont facilement accessibles.

Warning: A dedicated Listed circuit breaker rated at 15A is to be used for each

power supply connection.

Avertissement: Un disjoncteur cotée dédiée évalué à 15A doit être utilisée pour

chaque connexion d'alimentation.

Caution: Before mounting the device, ensure that the rack can support it

without compromising stability. Otherwise, personal injury and/or equipment

damage may result.

Caution: Follow appropriate ESD procedures when unpacking and handling

the switch. These include unpacking the switch in an ESD-safe environment

and wearing appropriate ESD protective gear, such as ESD-safe footwear and

ESD wrist straps where appropriate.

Caution: Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

Warning: Do not use optical instruments to view the laser output. The use of

optical instruments to view laser output increases eye hazard. Use only

UL/CSA, IEC/EN60825-1/-2 recognized pluggable modules.

Avertissement: Ne pas utiliser d'instruments optiques pour voir la sortie du

laser. L'utilisation de instruments optiques pour afficher la sortie laser

augmente les risques oculaires. Utilisez uniquement UL/CSA,

IEC/EN60825-1 /-2 reconnu modules enfichables.

Hardware Components

Figure 1 X590 Series Switch: Front Panel (24t Model Shown)

Figure 2 X590 Series Switch: Rear Panel

For component details, see the Hardware Installation Guide.

Operating Conditions

Operating Temperature:

0°C (32°F) to 45°C (113°F)

Storage Temperature:

-40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity:

5% to 95% (non-condensing)

Interfaces

Each X590 Series switch has a management port, a console port, and a

USB port. The following table lists the specific interfaces for each switch.

Note: The X590 ExtremeXOS Core License (Part no. 16795) is optional.

Power Specifications

Power Supply and Fan Options

1 Console/management port 4 10Gb/40Gb QSFP+ port

2 USB port 5

10Gb/25Gb/40Gb/50Gb/100Gb

capable

QSFP28 ports

3 100Mb/1Gb/10GBASE-T ports (24t) or

1Gb/10Gb SFP+ ports (24x)

Grounding lug 3 Modular power supply (AC input

shown)

Fan modules

X590-24t-1q-2c

(Part no. 16791)

X590 base unit with 24 100Mb/1Gb/10GBASE-T ports,

1 10Gb/40Gb QSFP+ port, 2 10Gb/25Gb/40Gb/50Gb/

100Gb capable QSFP28 ports, 2 unpopulated power

supply slots, 4 unpopulated fan module slots,

ExtremeXOS Advanced Edge License

X590-24x-1q-2c

(Part no.16790)

X590 base unit with 24 1Gb/10Gb SFP+ ports, 1 10Gb/

40Gb QSFP+ port, 2 10Gb/25Gb/40Gb/50Gb/100Gb

capable QSFP28 ports, 2 unpopulated power supply

slots, 4 unpopulated fan module slots, ExtremeXOS

Advanced Edge License

X590-24t-1q-2c

(Part no. 16791)

AC Input: 100-127VAC, 2.5A max. 50-60Hz for each PSU

AC Input: 200-240VAC, 1.25A max. 50-60Hz for each PSU

DC Input: -48 to -60VDC, 5.0A max. for each PSU

X590-24x-1q-2c

(Part no.16790)

AC Input: 100-127VAC, 2.5A max. 50-60Hz for each PSU

AC Input: 200-240VAC, 1.25A max. 50-60Hz for each PSU

DC Input: -48 to -60VDC, 5.0A max. for each PSU

X590-24t-1q-2c

X590-24x-1q-2c

Part no. 10960 770W AC power supply, Front-to-Back airflow

Part no. 10961 770W AC power supply, Back-to-Front airflow

Part no. 10962 1100W DC power supply, Front-to-Back airflow

Part no. 10963 1100W DC power supply, Back-to-Front airflow

Part no. 17115 X870 Fan Module, Front-to-Back airflow

Part no. 17116 X870 Fan Module, Back-to-Front airflow

Summary of content (2 pages)

PAGE 1
X590 Series Switch Quick Reference 3 Follow these steps to get your switch up and running. For complete installation instructions see the ExtremeSwitching and Summit Switches: Hardware Installation Guide at www.extremenetworks.com/documentation Tools You’ll Need Install the Switch You can install any X590 Series switch in a standard 19-inch equipment rack. There are four ways to mount the X590 Series switch in a rack: • Either the I/O ports or the power-supply side can face front.
PAGE 2
Getting Help For additional support related to X590 Series switches or this document, contact Extreme Networks using one of the following methods: Product Documentation https://www.extremenetworks.com/documentation/ Global Technical Assistance Center (GTAC) Phone: 1-800-998-2408 (toll-free in U.S. and Canada) or +1-408-579-2826. For the support phone number in your country, visit: http://www.extremenetworks.