User’s Manual HSA 200S & HSA 200SE HSA 200C & HSA 200CE HSA 222S & HSA 222C Hideaway® Surface Access Products Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
ᅝܼ乏ⶹ s Ё᭛ 䖭Ͼヺোᦤ⼎⫼᠋䆹䆒⫼᠋ݠЁ ᳝䞡㽕ⱘ᪡㓈ᡸ䇈ᯢDŽ 䖭Ͼヺো䄺ਞ⫼᠋䆹䆒ᴎݙ᳝ᲈ 䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ ⊼ᛣ 䯙䇏䇈ᯢк s 䑩ㅸỀ䑩嬦嫿⡈⼆枼敆嬼䍇夤ㆁ 㙊⫊₩⏍Ề䑩嬵㕏ɿ ֱᄬ䇈ᯢк s 䑩ㅸⷕ⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề 䑩ɿ 䙉ᅜ䄺ਞ s 䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊ ₩⏍㐎ẝ嬵㕏ɿ 䙓ܡ䗑ࡴ s ᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅₸ㅗ 弾⇡嫿⡈澤Ḧ忀₎⊲斪ɿ 䄺ਞ ⬉⑤ s 嬦嫿⡈⌫倾Ề䑩ᷨ␂ᵋ㝈㕏䗅䑶㷑ɿ 嫿⡈⼆枼Ề䑩 㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ 䩭ᵊ㚢一澠♱一澡㕰⫊₩嫿 㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ ᢨᥝ⬉⑤ s ᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿⡈⍏ ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅䑶㷑一ɿ ⬉⑤㒓ֱᡸ s ⣦Ⓟⵄ一澤 忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ 㓈ᡸ s ㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ 嫿⡈怩㯢 㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪ᵎ壂儫ⴲ 嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ 䗮亢ᄨ s 㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦敳㪣 㙻㒐だ₄ḷ弈䀮ɿ ᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛栏⪕ɿ 䫖⬉∴ s ᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ ⼆枼Ề䑩
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the Hideaway Surface Access Products ....... 1-2 About the Extender board line driver .................................. 1-4 Features ...................................................................................... 1-5 All models .............................................................................. 1-5 HSA 200CE and HSA 200SE models only ..............................
Table of Contents, cont’d Appendix A • Reference Information ............................ A-1 Specifications ......................................................................... A-2 HSA Part Numbers ................................................................ A-7 Included Parts ......................................................................... A-8 Routing Templates ............................................................... A-8 Accessories ................................................
Introduction About the Hideaway Surface Access Products The Extron Hideaway HSA 200 series and HSA 222 series are furniture-mounted, architectural solutions for inconspicuous computer video and/or network access and control.
Introduction The installed enclosures fit nearly flush within a table or podium top (figure 1-4), storing the connectors out of the way and out of sight. To access the connectors, the user presses down on the top of the enclosure, releasing a mechanical latch. A gas lift tips the connectors into view.
Introduction HSA 200/222 Series Surface Access Products 2 Chapter Two Installation Installation Overview Preparing the Routing Template Preparing the Table and Mounting the Enclosure Underside Features and Cabling Connections Front Panel Connectors Pre-installation Testing and Troubleshooting (HSA 200CE and HSA 200SE Models Only) 1-6 HSA 200/222 Series • Introduction
Installation Installation Overview Preparing the Routing Template Install and set up the HSA surface access enclosures as follows: 1 If you have an unprepared mounting template, prepare the template. See “Preparing the Routing Template” on the next page. 2 If desired, install the optional RJ-45 to RJ-11 conversion kit(s) to replace one or more RJ-45 connectors with RJ-11 connectors. Refer to the appropriate RJ-45 to RJ-11 Conversion Kit manual, for either the HSA 200 models or the HSA 222 models.
Installation, cont’d Preparing the Table and Mounting the Enclosure The preferred and recommended method for preparing the table is to use the appropriate Extron routing template and a router. See the part numbers for the templates in appendix A, “Reference Information”. For an HSA 200C, HSA 200CE, or HSA 222C unit (US version only), another preferred method is to use a 6" hole saw.
Installation, cont’d Preparing the table with a hole saw (HSA 200C, HSA 200CE, or HSA 222C—US version only) 1. Locate the desired mounting location on the tabletop or other installation surface. Mark the 6" circle, then find the center and mark it as well. Wear safety glasses when operating the hole saw. Failure to comply can result in eye injury. 2. 2. Using a 6" hole saw on a portable drill, cut the mounting hole at the desired location (figure 2-3).
Installation, cont’d Snugly tighten the Phillips head screws on the screw clamps to secure the enclosure to the surface. 5. Overtightening the Phillips head screws on the screw clamps can bend the clamp’s horizontal flange. CAUTION All HSA 200 models only 1 AC power outlet — Use this AC connector to: • 6. Tighten the locking thumbscrews on the screw clamps to lock the clamp in position. • 7. Peel any remaining protective coating from the enclosure.
Installation, cont’d All HSA 200 and HSA 222 models 4 Screw clamp bracket/screw clamp — These two brackets/ clamps hold the enclosure firmly in place in the mounting hole. 5 AC power input connection — Connect this cord to the power source. For US domestic versions, this power cord is permanently connected to the HSA. Connect the power cord to a 125VAC, 60 Hz, 5A power source. For international versions, this power cord is a removable IEC power cord.
Installation, cont’d Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw terminals and could pull out. Power connector wiring 1. See figure 2-10. Plug the input connector of the included 100-240 VAC, 50/60Hz, 12 VDC power supply into the AC power outlet on the underside of the enclosure ( 1 on figure 2-5). The two power cord wires must be kept separate while the power supply is plugged in. Remove power before continuing.
Installation, cont’d The Universal AC outlet is fully compatible with Europlug, British, Indian, Danish, and Italian plug types. See the universal AC outlet guide on the Extron Web site, www.extron.com, for compatibility details on all plug types. 2 3 Computer video input (HSA 200 models only) — Plug the VGA-UXGA output from a computer into this 15-pin HD female connector. 5A 6A 5B Front View 6B Audio input connector (HSA 200 models only) — Plug a 3.
Installation, cont’d Pre-installation Testing and Troubleshooting (HSA 200CE and HSA 200SE Models Only) HSA 200/222 Series Surface Access Products Before installing an HSA 200 with an Extender line driver into furniture, test the system to make sure that the connections and settings are correct. 1. Apply power to the line driver. The power/signal LED on the line driver will light to indicate that the line driver is receiving power.
Maintenance and Modifications The most probable corrective maintenance procedures for your HSA 200 or HSA 222 are leveling the top surface and replacing the gas lifts. Most of the maintenance procedures require removing the surface mount enclosure from the table. Removing and Replacing the Enclosure • The procedure for replacing the bezel in an HSA 222 only requires removing the HSA from the table. • The procedure for replacing the gas lift requires removing the HSA 200 or HSA 222.
Maintenance and Modifications, cont’d 2. (HSA 222 models only) Remove the four Phillips head screws from the front access panel (figure 3-1). Retain the screws. Lift the panel away from the enclosure. 3. (HSA 222 models only) Disconnect both RJ-45 connectors from the underside of the enclosure by simultaneously performing steps 3a and 3b: a.
Maintenance and Modifications, cont’d 4. Remove the four 1/16" hex head screws on the right and left sides of the front panel (figure 3-3). Retain the screws. Lift the panel away from the enclosure. 8. Snap the internal RJ-45 connector onto the back of the front panel enclosure bezel plug-in. 9. (HSA 222 models only) Reach your hand through the front panel access hole and snap the lower internal RJ-45 connectors onto the back of the lower enclosure bezel plug-ins. 10.
Maintenance and Modifications, cont’d Replacing the Gas Lift The gas lift that raises the HSA surface is rated for 100,000 opening and closing cycles. Contact the Extron S3 Sales & Technical Support Hotline at the nearest phone number listed on the rear cover of this manual to obtain a replacement gas lift. Replace the gas lift as follows: 3. Slide the gas lift mounting plate toward the center of the enclosure, releasing the mounting plate (figure 3-5). 4.
Maintenance and Modifications, cont’d 7. (HSA 222 models only) Remove the four Phillips head screws from the front access panel (figure 3-7). Retain the screws. Lift the panel away from the enclosure. 8. Remove the pivot nut from the upper pivot bolt, then remove the bolt, releasing the upper end of the gas lift from the top panel. Pull the gas lift from the bottom of the enclosure. HSA 200 models — Reach through the front panel opening (figure 3-8).
Maintenance and Modifications, cont’d Adjusting the Top Panel Level the top panel of the HSA 200 or HSA 222 as follows: Remove pivot nut. 1. If necessary to view the top and the underside of the enclosure simultaneously, remove the surface mount enclosure from the table. See “Removing and Replacing the Enclosure”, steps 1 through 4. 2. Close and latch the top panel. 3. Slightly loosen the two latch locking screws (figure 3-10) on the underside of the surface mount enclosure.
Maintenance and Modifications, cont’d HSA 200/222 Series Surface Access Products A Appendix A Reference Information Specifications HSA Part Numbers Included Parts Routing Templates Replacement Parts Accessories Top Plate Dimensions 3-14 HSA 200/222 Series • Maintenance and Modifications
Reference Information Audio — HSA 200SE, HSA 200CE Specifications Video — HSA 200SE, HSA 200CE Gain ................................. Bandwidth ..................... Selectable: unity (0.7 V), (0.75 V) 50%, (0.8 V) 100% 300 MHz (-3 dB) ID bits are terminated on pins 4 and 11. Video input — HSA 200S, HSA 200C Number/signal type .... Connectors ..................... 1 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs (1) 15-pin HD female Video input — HSA 200SE, HSA 200CE Number/signal type .... Connectors ...........
Reference Information, cont’d General The Universal AC outlet is fully compatible with Europlug, British, Indian, Danish, and Italian plug types. See the Universal AC outlet guide on the Extron Web site, www.extron.com, for compatibility details on all plug types Power (HSA 200SE/CE) Supplied by an external power supply External power supply (HSA 200SE/CE) 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 0.42 A, regulated Power input requirements (HSA 200SE/CE) 12 VDC, 0.
Reference Information, cont’d HSA 200C/HSA 200CE — international circular models Top plate (outer rim) ................... 8.5" diameter circle (21.6 cm diameter) circle Surface cutout (inside rim) ......... 8.0" diameter (20.3 cm diameter) circle Top plate (inside tilt plate) ......... 5.9" W x 4.1" D (15.1 cm W x 10.4 cm D) HSA 200 — international, all models Box (under surface) ..................... 4.0" H x 6.3" W (front of unit) x 5.0" D (10.2 cm H x 15.9 cm W x 12.7 cm D) without clamps 4.0" H x 10.
Reference Information, cont’d Included Parts Part HSA 200S/HSA 200SE/HSA 222S US Models 6.470" (16.43 cm) Part number HSA 200 and HSA 222 User’s Manual 5.970 + 0.0325" (15.16 + 0.083 cm) RJ-45 connector bezel plug-in inserts (assorted colors) 70-201-01 Power supply, 100-240VAC, 50/60Hz, 12VDC (HSA 200SE and HSA 200 CE only) SURFACE CUT-OUT AREA = 5.970 + 0.0325" (15.16 + 0.083 cm) x 4.625 + 0.0325" (11.75 + 0.083 cm) 4.625 + 0.0325" 28-104-01 Tweeker Routing Templates Template (11.75 + 0.
Reference Information, cont’d HSA 200C/HSA200CE/HSA222C US Models 6.5" (16.5 cm) 6.000 + 0.0325" (15.24 + 0.083 cm) SURFACE CUT-OUT AREA = 6.000 + 0.0325" (15.24 + 0.083 cm) diameter Cut surface material out along this line. Tilting Plate Top Panel User Access (Connectors and AAP Openings) TEMPLATE IS NOT FULL SIZE. HSA 200C/HSA 200CE International Models 8.5" (21.6 cm) 8.0" (20.3 cm) HSA 200/222 Series Surface Access Products B Appendix B Packaging for Shipment SURFACE CUT-OUT AREA = 8.0" (20.
Packaging for Shipment The HSA 200’s and HSA 222’s ultra-fine machined surfaces and moving parts make them vulnerable to damage caused by mishandling during shipment, if they are improperly packaged. If, for any reason, you need to return an HSA to Extron, first contact Extron to obtain a return kit. The return kit, which reduces the chances of damage during shipment, includes a sturdy shipping carton and foam shells custom cut to fit the HSA (figure B-1). 2.
Packaging for Shipment, cont’d 6. Place the remaining foam shell on the other side of the HSA (figure B-4). Firmly push the foam shells together as far as they will go to completely suspend the HSA unit. Figure B-4 — HSA unit suspended in the foam 7. Place the foam-protected HSA 200 or HSA 222 into the shipping carton (figure B-5). Figure B-5 — HSA in the shipping carton B-4 8. Close the shipping carton and seal it with high quality shipping tape. 9.