MVX Matrix Switcher Part Numbers These items are included in each order for a MVX A matrix switcher: Matrix switcher part numbers Replacement part number MVX 128 VGA A 60-799-01 MVX 1212 VGA A 60-858-01 MVX 168 VGA A 60-838-01 MVX 1616 VGA A 60-839-01 Setup Guide MVX VGA A Computer Video (VGA) and Audio Matrix Switchers Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Table of Contents Chapter One • Introduction ..................................................... 1-1 About this Manual ..................................................................... 1-2 About the Matrix Switchers ................................................... 1-2 Chapter Two • Installation ....................................................... 2-1 Rear Panel Installation Features ............................................ 2-2 Front Panel Configuration Port . ...............................
Table of Contents, cont’d MVX VGA A Matrix Switchers 1 Chapter One Introduction About this Manual About the Matrix Switchers ii MVX VGA A Matrix Switchers • Table of Contents Refer also to the MVX VGA A User’s Manual at www.extron.com.
Introduction N For more information on any subject in this guide, refer to the MVX VGA A User’s Manual, available on the Extron DVD or at www.extron.com. About this Manual This setup guide allows you to easily and quickly set up and configure your matrix switcher.
Installation Rear Panel Installation Features N The MVX VGA 128 A does not have the Sync Impedance 3 1 switches described below. 2 c MVX 1616 VGA A 1 5 COMPUTER IN 13 9 COMPUTER OUT 9 13 6 10 14 3 7 11 15 4 8 12 16 1 5 2 A na he im, C A 6 14 10 ® 3 7 11 15 4 8 12 16 US LISTED 1T23 I.T.E. SYNC IMPEDANCE 50 1 2 3 4 5 6 7 8 Each switch provides the option of selecting either 50 ohms or 75 ohms.
Installation, cont’d Front Panel Configuration Port CONTROL ENTER PRESET IO VIEW ESC RGBHV AUDIO CONFIG MVX SERIES VGA MATRIX SWITCHER WITH ADSP TM 8 h Configuration port — If desired, connect a control or computer to the front panel Configuration (RS-232) port. Use an optional 9-pin D to 2.5 mm mini jack TRS RS-232 cable, part #70-335-01.
Front Panel Operation Creating a Tie 1. INPUTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONTROL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ENTER PRESET VIEW Press and release the Esc button to clear any button indicators that may be lit. I/O ESC VIDEO Press the Esc button to clear all selections.
Front Panel Operation, cont’d Saving or Recalling a Preset 1. Setting the Front Panel Locks (Executive Modes) Save a preset — Press and hold the Preset button until it flashes. The matrix switcher has three levels of front panel security lock that limit the operation of the switcher from the front panel. The three levels are: Recall a preset — Press and release the Preset button. Save a preset Press and hold. 2 seconds Preset LED blinks.
Front Panel Operation, cont’d Viewing Ties (and Muting Outputs) Selecting Lock mode 2 or toggling between mode 2 and mode 1 1. N If the switcher is in Lock mode 0 or mode 1, this procedure Press the View button. Output LEDs light for outputs that have no ties established. selects mode 2. N If an output LED blinks, that output is muted. If the switcher is in Lock mode 2, this action selects mode 1. 2. Press an input button. The LEDs for all tied outputs light.
Front Panel Operation, cont’d MVX VGA A Matrix Switchers 4 Chapter Four Remote Control Selected SIS Commands Installing and Starting the Control Program Button Label Generator Program 3-8 MVX VGA A Matrix Switchers • Front Panel Operation Refer also to the MVX VGA A User’s Manual at www.extron.com.
4-2 MVX VGA A Matrix Switchers • Remote Control Refer also to the MVX VGA A User’s Manual at www.extron.com. (host to switcher) ASCII command Response (switcher to host) Additional description Refer also to the MVX VGA A User’s Manual at www.extron.com.
Command ASCII command (host to switcher) Response (switcher to host) Additional description Create ties • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*8$. • The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%). N When you create a tie where X! = 00, you tie no input to the specified output (X@) (untie X@). N MVX VGA A Matrix Switchers • Remote Control Refer also to the MVX VGA A User’s Manual at www.
ASCII command (host to switcher) Response (switcher to host) Additional description Video and audio mute commands Refer also to the MVX VGA A User’s Manual at www.extron.com. MVX VGA A Matrix Switchers • Remote Control Read RGB/video mute X@*1B X@*0B X@B Global RGB/video mute 1*B Global RGB/video unmute 0*B Audio mute Read audio mute X@*1Z X@*0Z X@Z Global audio mute 1*Z Global audio unmute 0*Z View output mutes EVM} X#] Vmt1] Vmt0] AmtX@*1] AmtX@*0] X#] Amt1] Amt0] X$1X$2X$3 ...
ASCII command (host to switcher) Response (switcher to host) Additional description Lock (executive) modes Refer also to the MVX VGA A User’s Manual at www.extron.com. MVX VGA A Matrix Switchers • Remote Control N See “Setting the front panel locks (Executive modes)” on page 3-4 for more information on the Lock modes. Lock all front panel functions 1X Enable Lock mode 1. Exe1] Lock advanced front panel functions 2X Exe2] Enable Lock mode 2.
4-6 (host to switcher) ASCII command Response (switcher to host) Additional description N VrbX1@] X1@] EX1@CV} ECV} Q Q X1)] X1!] 1.23] VX*XX(•AX*XX(] The factory-installed controller firmware version is 1.23 (sample value only). VX*XX( = video size, AX*XX( = audio size Enable Lock mode 0. Exe0] X&] Enable Lock mode 2. Exe2] N I X 0X 2X X1@ = Verbose mode MVX VGA A Matrix Switchers • Remote Control Refer also to the MVX VGA A User’s Manual at www.extron.com.
Remote Control, cont’d 4. Follow the on-screen instructions. The installation program creates a C:\Program Files\Extron\ Matrix_Switchers directory and an “Extron Electronics\ Matrix Switchers” group folder. It installs the following four programs: • • • • MATRIX Switcher+ Control Program MATRIX Switcher+ Help Uninstall MATRIX Switcher Check for Matrix Updates Starting the program 1.
Remote Control, cont’d 4-10 MVX VGA A Matrix Switchers • Remote Control Refer also to the MVX VGA A User’s Manual at www.extron.com.
