User’s Manual IR REMOTE MIN. UNITY MAX. INPUT 3 SCP 100P SCP 100P Control Panel www.extron.com Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Table of Contents Chapter 1 • Introduction and Installation ................... 1-1 About the SCP 100P .............................................................. 1-2 Installation Instructions .................................................... 1-2 Preparing the site, installing the wall box ........................... 1-2 Rear panel (circuit board) and cabling ................................. 1-4 Pre-installation testing/troubleshooting ..............................
Table of Contents, cont’d SCP 100P 1 Chapter One Introduction and Installation About the SCP 100P Installation Instructions ii SCP 100P • Table of Contents
Introduction and Installation, cont’d Introduction and Installation About the SCP 100P 4. The Extron SCP 100P control panel replicates the front panel controls of the Extron System 5cr Plus system switcher, and it is also compatible with the System 5cr switcher. The Input 3 button on the control panel corresponds to the PC3 button on the front panel of the System 5cr. Up to two SCP 100Ps can be connected to the System 5cr/5cr Plus.
Introduction and Installation, cont’d Rear panel (circuit board) and cabling SCP 100P, and watching the LEDs on the switcher to see if the system switches to the desired inputs. The connections between the SCP 100P and the System 5cr Plus can be tested even if input/output devices are not available. 1 Mounting the SCP to the wall box Once the system has been cabled and tested, the control pad can be installed in the wall or furniture. 1 Rear panel port — Connect this 3.
Introduction and Installation, cont’d Application diagram Below is an example of a typical installation of an SCP 100P control pad and a System 5cr Plus switcher. SYSTEM 5 ROOM POWER DISPLAY MUTE AUDIO MODE PC1 PC2 PC INPUT 3 VID1 AUDIO VID2 VID VID VID Y/C Y/C Y/C Plus IR PC1 INPUT COMPUTER MAX. CLIP MIN. VOLUME TX CONFIG RETRY RX LEARN Front IR 40 Remote LIGHTING ROOM POWER MUTE MODE VOLUME MAX. CLIP MIN.
Operation, cont’d Operation The SCP 100P replicates the front panel controls of the System 5cr Plus. Display Power button and LED — Once the System 5cr Plus has been programmed with the commands for the specific projector, pressing this button toggles the projector’s power on or off. The System 5cr Plus cannot be configured from the SCP 100P control pad. All switcher setup must be done from the switcher’s front panel or via RS-232 control. The LED lights when projector power is on.
Operation, cont’d 5 Volume control knob — Rotate this knob to adjust the audio volume (audio gain) for the amplified output. The volume control knob can be used as a master volume control for both audio outputs if all the audio inputs have the same level. There is no physical limit to this knob’s rotation. The Min or Max LED will light briefly when the knob has reached its functional minimum or maximum limit.
Specifications, Parts, Accessories, Dimensions, cont’d Specifications, Parts, Accessories, Dimensions Specifications Accessories These recommended items are available from Extron: Control/remote — control pad IR controller module ......... IR 401 (optional) Part number Cable/accessory General Power ................................... 12VDC, at 60 mA, from the System 5cr Plus switcher Temperature/humidity ....
Specifications, Parts, Accessories, Dimensions, cont’d Template Use the template as a guide to mark and cut the hole in the wall or furniture through which the SCP 100P will be installed. The template includes the recommended 0.1” (0.25 cm) clearance on all sides of the electrical wall box to allow room for the raised areas surrounding the knockouts. See chapter two for details on installing the SCP 100P. The light gray area represents the layout of the electrical box (3.75"H x 3.