User's Manual

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
XTP PI 400 Power Injector • Setup Guide
The Extron XTP PI 400 Power Injector is a midspan power injector for XTP products. It provides power over LAN for up to four
XTP endpoints. This guide provides instructions for an experienced installer to install and connect the XTP PI 400.
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
1
XTP POWER OUT
XTP PI 400
XTP POWER INJECTOR
2 3 4
Rear Panel
Front Panel
Installation
WARNING: Risk of electrical shock. To reduce the risk of
re or electric shock, do not expose this apparatus to rain,
moisture, dripping, splashing, or objects lled with liquids.
Step 1— Mounting
The XTP PI 400 is 1U high and one-half rack wide.
a. Turn off or disconnect all equipment power sources.
b. Mount the XTP PI 400 in a rack shelf (see the image to the right) or
under a desk using an optional mounting kit.
Step 2 — Cabling
ATTENTION: Do not connect this device to a computer data or telecommunications network.
NOTE: The XTP PI 400 does not switch XTP signals.
For the best performance, see Twisted Pair Cable Termination and
Recommendations on page 2.
a. Using a CATx cable, connect an Extron XTP device to the XTP connector on
one of the four port pairs. The XTP device plugged into this connector must
be powered by a local power source.
b. Using a CATx cable, connect an XTP device that requires power from an
external source to the XTP Pwr connector.
c. Repeat steps 2a and 2b for each XTP port pair as necessary.
NOTE: Do not loop XTP port pairs on a single cable run to remotely power the transmitter and receiver.
Figure 2, below, shows this type of application, which is not recommended by Extron.
d. Connect AC power to the XTP PI 400.
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
NOTE: Using scre
ws longer
than 3/16" will damage the
unit and void the warranty.
RSU 129 Universal Rack Shelf
Front false
faceplate
uses 2
screws.
Half Rack 9.5 inch Box Standard Shelf
1/2 Rack Width Front False
Faceplate
XTP
PWR
XTP PWR
To an XTP Device To an XTP Device
that Requires an
External Power Supply
ÇÉ
Figure 1. Correct Application
Figure 2. Incorrect Application
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
Rx GTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
POWER
12V
HDMI
--A MAX
Rx GTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
CATx
XTP T HDMI
Transmitter
XTP R HDMI
Receiver
CORRECT
INCORRECT
XTP PI 400
XTP Power Injector
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
Rx GTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
CATx
XTP R HDMI
Receiver
XTP PI 400
XTP Power Injector
CATx
Remote Power
POWER
12V
HDMI
--A MAX
Rx GTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
XTP T HDMI
Transmitter
Remote Power
Remote Power
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
Rx GTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
POWER
12V
HDMI
--A MAX
Rx GTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
CATx
XTP T HDMI
Transmitter
XTP R HDMI
Receiver
CORRECT
INCORRECT
XTP PI 400
XTP Power Injector
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
Rx GTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
CATx
XTP R HDMI
Receiver
XTP PI 400
XTP Power Injector
CATx
Remote Power
POWER
12V
HDMI
--A MAX
Rx GTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
XTP T HDMI
Transmitter
Remote Power
Remote Power