Instructions / Assembly

ManualsBrandsEZ-ACCESS ManualsAccessibility Ramps3 ft. Angled Entry Ramp

Instructions

TRANSITIONS

Angled Entry Ramp

Available in 12-, 24-, and 36-inch lengths

14134 REV 05-12-15

LIFETIME WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction.

CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Horth Mymms Hatfield, AL9 5SD, UK

All text and images contained in this document are proprietary and may not be shared, modified,

distributed, reproduced, or reused without the express written permission of EZ-ACCESS.

Fasten ramp using

proper fasteners and

pre-drilled holes.

IMPORTANT INFORMATION

Rated load is 700 pounds, 350 pounds per caster or wheel.

Never exceed rated load.

Read and follow all labels, instructions, safety and

maintenance information before use.

For additional care, use or safety information, or to obtain

replacement copies, please call 1-800-451-1903 or visit

www.ezaccess.com.

Do not use if ramp is damaged or unstable.

For wheelchairs and scooters only (not intended for

commercial use).

Ramp may be slippery when wet or icy.

Use only if sufficient maneuvering room is available at both

ends of the ramp to assure safe travel when entering and

exiting the ramp.

Use ramp only with a qualified helper and always use your

lap belt.

It is important that you refer to your equipment's

(wheelchair or scooter) User Guide for the proper degree of

incline or decline and chair direction before attempting

ramp use. Never exceed its recommendations.

GETTING STARTED

1. The aluminum, self-supporting ramp can be used with or

without the supplied adjustable swivel feet. To protect

floors, foam, rubber, or other non-abrasive, protective

material may be affixed to the underside of ramp.

2. Use the chart below to view the different rise ranges

(adjustable range is determined by use of foot size).

Measure the rise to determine if the adjustable swivel feet

are needed.

The TAER 24 comes with two sizes of swivel feet.

SWIVEL FEET

PART NO.

NO FEET

1-1/2"

2-1/2"

TAER 12

1-3/8"

1-15/16" to 2-3/4"

N/A

TAER 24

1-11/16"

N/A

2-1/8" to 3-3/8"

3-3/16" to 4-3/8"

TAER 36

3-5/16"

N/A

3-5/8" to 5-7/8"

3. Position the ramp and adjustable feet as needed to

obtain correct height (FIG. 1). Adjust feet as needed to

ensure both feet are in contact with the ground.

FASTENING RAMP TO LANDING

The Transitions Angled Entry Ramp must be

fastened to the landing before use.

Use the two pre-drilled holes in the bottom

of the ramp to fasten to the landing or

threshold. Wood screws, sheet metal

screws, or concrete bolts may be

necessary, depending on the application.

1. ATTACHING TO WOOD

1.1 Fasten Transitions Angled Entry Ramp by

installing one 1/4” x 1” self-drilling stainless

steel screw (supplied) through each hole as

shown (FIG. 2).

2. ATTACHING TO CONCRETE

2.1 Use the two pre-drilled holes in the bottom of

the Transitions Angled Entry Ramp as a

template to mark the positions to drill.

2.2 Using a 1/4” masonry bit, drill two holes at the

marked locations. Drill to a depth specified by

the pin drive anchor manufacturer’s instructions.

2.3 After drilling, make sure that the holes are free

of any residue and/or debris.

2.4 Align the Transitions Angled Entry Ramp over

the drilled holes.

2.5 Install 1/4” x 1 1/2” pin drive concrete anchors

(not supplied) into the holes per the pin drive

anchor manufacturer’s instructions.

SAFETY & MAINTENANCE

1. Regularly check ramp for damage and tighten any loose

fasteners.

2. Keep ramp surface clear of ice, snow, dirt, leaves, and

other debris. For snow or ice, remove accumulation and

sweep surface clean. To remove dirt, leaves, and other

debris, sweeping the surface or using a garden hose will

usually suffice. If needed, use a damp cloth or soft brush

with non-alkaloid detergent and water. Rinse well and use

extra caution if ramp surface is wet.

FIG. 1

FIG. 2

To insert, rotate

swivel foot

clockwise to

thread into

nutsert. Do not

over tighten.