Datasheet

ManualsBrandsFAIRCHILD SEMICONDUCTOR ManualsOptoelectronics & DisplaysMOC3010SR2M

MOC301XM, MOC302XM — 6-Pin DIP Random-Phase Optoisolators Triac Driver Output (250/400 Volt Peak)

MOC301XM, MOC302XM Rev. 1.0.3

March 2014

MOC3010M, MOC3011M, MOC3012M,

MOC3020M, MOC3021M, MOC3022M, MOC3023M

6-Pin DIP Random-Phase Optoisolators Triac Driver Output

(250/400 Volt Peak)

Features

■

Excellent I

Stability—IR Emitting Diode Has Low

Degradation

■

High Isolation Voltage—Minimum 5300 V

AC(RMS)

■

Underwriters Laboratory (UL) Recognized—

File #E90700

■

Peak Blocking Voltage

– 250 V, MOC301XM

– 400 V, MOC302XM

■

VDE Recognized (File #94766)

– Ordering Option V (e.g., MOC3023VM)

Applications

■

Industrial Controls

■

Solenoid/Valve Controls

■

Traffic Lights

■

Static AC Power Switch

■

Vending Machines

■

Incandescent Lamp Dimmers

■

Solid State Relay

■

Motor Control

■

Lamp Ballasts

Description

The MOC301XM and MOC302XM series are optically

isolated triac driver devices. These devices contain a

GaAs infrared emitting diode and a light activated silicon

bilateral switch, which functions like a triac. They are

designed for interfacing between electronic controls and

power triacs to control resistive and inductive loads for

115 V

operations.

Schematic Package Outlines

MAIN TERM.

NC*

N/C

*DO NOT CONNECT

(TRIAC SUBSTRATE)

ANODE

CATHODE

MAIN TERM.

Figure 1. Schematic

Figure 2. Package Outlines

Summary of content (14 pages)

PAGE 1
MOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M 6-Pin DIP Random-Phase Optoisolators Triac Driver Output (250/400 Volt Peak) Features Description ■ Excellent IFT Stability—IR Emitting Diode Has Low The MOC301XM and MOC302XM series are optically isolated triac driver devices. These devices contain a GaAs infrared emitting diode and a light activated silicon bilateral switch, which functions like a triac.
PAGE 2
As per DIN EN/IEC60747-5-2. This optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings is ensured by means of protective circuits. Symbol Parameter Min. Typ. Max. Unit Installation Classifications per DIN VDE 0110/1.89 see Table 1 For Rated Mains Voltage < 150 VRMS I–IV For Rated Mains Voltage < 300 VRMS I–IV Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110/1.
PAGE 3
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. TA = 25°C unless otherwise specified.
PAGE 4
Individual Component Characteristics Symbol Parameters Test Conditions Device Min. Typ. Max. Units EMITTER VF Input Forward Voltage IF = 10 mA All 1.15 1.50 V IR Reverse Leakage Current VR = 3 V, TA = 25°C All 0.01 100 µA DETECTOR IDRM Peak Blocking Current, Either Direction Rated VDRM, IF = 0(2) All 10 100 nA VTM Peak On-State Voltage, Either Direction ITM = 100 mA peak, IF = 0 All 1.8 3.0 V Typ. Max.
PAGE 5
1.8 800 1.7 ITM - ON-STATE CURRENT (mA) V F - FORWARD VOLTAGE (V) 600 1.6 1.5 1.4 TA = -55oC 1.3 TA = 25oC 1.2 TA = 100oC 1.1 400 200 0 -200 -400 -600 1.0 -800 1 10 100 -3 -2 IF - LED FORWARD CURRENT (mA) Figure 3. LED Forward Voltage vs. Forward Current 0 1 2 3 Figure 4. On-State Characteristics 1.4 25 IFT - TRIGGER CURRENT (NORMALIZED) ITM - TRIGGER CURRENT (NORMALIZED) -1 VTM - ON-STATE VOLTAGE (V) 1.3 1.2 1.1 1.0 0.9 0.8 15 10 5 0 0.
PAGE 6
1. The mercury wetted relay provides a high speed repeated pulse to the D.U.T. RTEST R = 10 kΩ 2. 100x scope probes are used, to allow high speeds and voltages. CTEST PULSE INPUT MERCURY WETTED RELAY DUT 3. The worst-case condition for static dv/dt is established by triggering the DUT with a normal LED input current, then removing the current.
PAGE 7
Rin VCC 1 2 6 MOC3010M MOC3011M MOC3012M 180 Ω 120 V 60 Hz 5 3 1.2 kΩ 0.2 μF C1 4 Figure 12. Inductive Load with sensitive Gate Triact (IGT ≤ 15 mA) Rin 1 6 360 Ω 470 Ω HOT VCC 2 3 MOC3020M MOC3021M MOC3022M MOC3023M 5 0.05 μF 39 240 VAC 4 0.01 μF LOAD GROUND In this circuit the “hot” side of the line is switched and the load connected to the cold or ground side. The 39 Ω resistor and 0.01 µF capacitor are for snubbing of the triac, and the 470 Ω resistor and 0.
PAGE 8
MOC301XM, MOC302XM — 6-Pin DIP Random-Phase Optoisolators Triac Driver Output (250/400 Volt Peak) Reflow Profile 300 260°C 280 260 >245°C = 42 s 240 220 200 180 °C Time Above 183°C = 90 s 160 140 120 1.822°C/s Ramp-up Rate 100 80 60 40 33 s 20 0 0 60 120 180 270 360 Time (s) Figure 14. Relow Profile ©2005 Fairchild Semiconductor Corporation MOC301XM, MOC302XM Rev. 1.0.3 www.fairchildsemi.
PAGE 9
Option Order Entry Identifier (Example) No option MOC3010M S MOC3010SM SR2 MOC3010SR2M T MOC3010TM 0.4" Lead Spacing V MOC3010VM VDE 0884 TV MOC3010TVM VDE 0884, 0.
PAGE 10
Figure 15. 6-Pin DIP Through Hole Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products.
PAGE 11
Figure 16. 6-Pin DIP Surface Mount Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products.
PAGE 12
Figure 17. 6-Pin DIP 0.4” Lead Spacing Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products.
PAGE 13
12.0 ± 0.1 4.5 ± 0.20 2.0 ± 0.05 0.30 ± 0.05 4.0 ± 0.1 Ø1.5 MIN 1.75 ± 0.10 11.5 ± 1.0 21.0 ± 0.1 9.1 ± 0.20 0.1 MAX 10.1 ± 0.20 24.0 ± 0.3 Ø1.5 ± 0.1/-0 User Direction of Feed Note: All dimensions are in millimeters. Figure 18. Carrier Tape Specification ©2005 Fairchild Semiconductor Corporation MOC301XM, MOC302XM Rev. 1.0.3 www.fairchildsemi.
PAGE 14
MOC301XM, MOC302XM — 6-Pin DIP Random-Phase Optoisolators Triac Driver Output (250/400 Volt Peak) 14 www.fairchildsemi.com ©2005 Fairchild Semiconductor Corporation MOC301XM, MOC302XM Rev. 1.0.