Datasheet

ManualsBrandsFAIRCHILD SEMICONDUCTOR ManualsOptoelectronics & DisplaysMOC3062SM

MOC306XM, MOC316XM — 6-Pin DIP Zero-Cross Phototriac Driver Optocoupler (600 Volt Peak)

MOC306XM, MOC316XM Rev. 1.0.4

September 2010

MOC3061M, MOC3062M, MOC3063M,

MOC3162M, MOC3163M

6-Pin DIP Zero-Cross Phototriac Driver Optocoupler

(600 Volt Peak)

Features

■

Simplifies logic control of 115/240 VAC power

■

Zero voltage crossing

■

dv/dt of 1000V/µs guaranteed (MOC316X-M),

– 600V/µs guaranteed (MOC306X-M)

■

VDE recognized (File # 94766)

– ordering option V (e.g., MOC3063V-M)

■

Underwriters Laboratories (UL) recognized

(File #E90700, volume 2)

Applications

■

Solenoid/valve controls

■

Static power switches

■

Temperature controls

■

AC motor starters

■

Lighting controls

■

AC motor drives

■

E.M. contactors

■

Solid state relays

Description

The MOC306XM and MOC316XM devices consist of a

GaAs infrared emitting diode optically coupled to a

monolithic silicon detector performing the function of a

zero voltage crossing bilateral triac driver. They are

designed for use with a triac in the interface of logic sys-

tems to equipment powered from 115/240 VAC lines,

such as solid-state relays, industrial controls, motors,

solenoids and consumer appliances, etc.

Schematic Package Outlines

MAIN TERM.

NC*

N/C

*DO NOT CONNECT

(TRIAC SUBSTRATE)

ANODE

CATHODE

MAIN TERM.

ZERO

CROSSING

CIRCUIT

Summary of content (11 pages)

PAGE 1
MOC3061M, MOC3062M, MOC3063M, MOC3162M, MOC3163M 6-Pin DIP Zero-Cross Phototriac Driver Optocoupler (600 Volt Peak) Features Description ■ Simplifies logic control of 115/240 VAC power The MOC306XM and MOC316XM devices consist of a GaAs infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing bilateral triac driver.
PAGE 2
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only.
PAGE 3
Individual Component Characteristics Symbol Parameters Test Conditions Device Min. Typ.* Max. Units EMITTER VF Input Forward Voltage IF = 30mA All 1.3 1.5 V IR Reverse Leakage Current VR = 6V All 0.
PAGE 4
As per IEC 60747-5-2, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits. Symbol Parameter Min. Typ. Max. Unit Installation Classifications per DIN VDE 0110/1.89 Table 1 For Rated Main Voltage < 150Vrms I-IV For Rated Main voltage < 300Vrms I-IV Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/1.
PAGE 5
Figure 2. Trigger Current Vs. Temperature Figure 1. LED Forward Voltage vs. Forward Current 1.6 1.7 1.5 VTM = 3V NORMALIZED TO TA = 25°C 1.5 1.4 1.4 IFT, NORMALIZED VF, FORWARD VOLTAGE (V) 1.6 1.3 TA = -40°C 1.2 TA = 25°C 1.1 1.0 TA = 85°C 1.3 1.2 1.1 1.0 0.9 0.9 0.8 0.7 0.1 1 10 0.8 -40 100 -20 IF, LED FORWARD CURRENT (mA) Figure 3. LED Current Required to Trigger vs. LED Pulse Width 20 40 60 80 100 Figure 4. Leakage Current, IDRM vs.
PAGE 6
Figure 6. On-State Characteristics Figure 5. IDRM2, Leakage in Inhibit State vs. Temperature 800 2.4 IF = RATED IFT NORMALIZED TO TA = 25°C 2.2 600 ITM, ON-STATE CURRENT (mA) 2.0 IDRM2, NORMALIZED 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 TA = 25°C 400 200 0 -200 -400 -600 -20 0 20 40 60 80 -800 -4 100 -3 TA, AMBIENT TEMPERATURE (°C) Figure 7. IH, Holding Current vs. Temperature -1 0 1 2 3 4 Figure 8. Inhibit Voltage vs. Temperature 3.2 1.20 2.8 1.15 NORMALIZED TO TA = 25°C 1.10 2.
PAGE 7
2. The worst-case condition for static dv/dt is established by triggering the D.U.T. with a normal LED input current, then removing the current. The variable vernier resistor combined with various capacitor combinations allows the dv/dt to be gradually increased until the D.U.T. continues to trigger in response to the applied voltage pulse, even after the LED current has been removed. The dv/dt is then decreased until the D.U.T. stops triggering. tRC is measured at this point and recorded.
PAGE 8
Through Hole 0.4" Lead Spacing 8.13–8.89 6 4 8.13–8.89 6 4 1 3 6.10–6.60 6.10–6.60 Pin 1 1 3 Pin 1 5.08 (Max.) 3.28–3.53 0.25–0.36 7.62 (Typ.) 5.08 (Max.) 3.28–3.53 0.38 (Min.) 0.25–0.36 2.54–3.81 0.38 (Min.) 2.54 (Bsc) (0.86) 0.41–0.51 2.54–3.81 0.20–0.30 15° (Typ.) 2.54 (Bsc) (0.86) 1.02–1.78 0.41–0.51 0.76–1.14 0.20–0.30 10.16–10.80 1.02–1.78 0.76–1.14 Surface Mount (1.78) 8.13–8.89 6 4 (1.52) (2.54) (7.49) 6.10–6.60 8.43–9.90 Pin 1 (10.54) 1 3 (0.
PAGE 9
Option Order Entry Identifier (Example) No option MOC3061M S MOC3061SM SR2 MOC3061SR2M T MOC3061TM 0.4" Lead Spacing V MOC3061VM VDE 0884 TV MOC3061TVM VDE 0884, 0.
PAGE 10
12.0 ± 0.1 4.5 ± 0.20 2.0 ± 0.05 Ø1.5 MIN 4.0 ± 0.1 0.30 ± 0.05 1.75 ± 0.10 11.5 ± 1.0 21.0 ± 0.1 9.1 ± 0.20 Ø1.5 ± 0.1/-0 10.1 ± 0.20 0.1 MAX 24.0 ± 0.3 User Direction of Feed Reflow Profile 300 260°C 280 260 >245°C = 42 Sec 240 220 200 180 °C Time above 183°C = 90 Sec 160 140 120 1.822°C/Sec Ramp up rate 100 80 60 40 33 Sec 20 0 0 60 120 180 270 360 Time (s) ©2005 Fairchild Semiconductor Corporation MOC306XM, MOC316XM Rev. 1.0.4 10 www.fairchildsemi.
PAGE 11
AccuPower™ Auto-SPM™ Build it Now™ CorePLUS™ CorePOWER™ CROSSVOLT™ CTL™ Current Transfer Logic™ DEUXPEED® Dual Cool™ EcoSPARK® n EfficientMax™ ESBC™ ® Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT® FAST® FastvCore™ FETBench™ FlashWriter®* FPS™ F-PFS™ FRFET® SM Global Power Resource Green FPS™ Green FPS™ e-Series™ Gmax™ GTO™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ MicroPak2™ MillerDrive™ MotionMax™ Motion-SPM™ OptoHiT™ OPTOLOGIC® OPTOPLANAR® ® PDP SPM™ Power-SPM™