Use and Care Manual

ManualsBrandsFAMOWOOD ManualsKitchen1-gal. Glaze Coat Clear Epoxy Kit (2-Pack)

Technical

Data Sheet

FAMOWOOD GLAZE COAT

HIGH BUILD EPOXY COATING

FAMOWOOD GLAZE COAT|USA/CAN/MEX/AU/NZ|Rev 17 – Effective:12.30.19 Approved: TMorgan(12/30/19)/MStark (6.13.19) /EDavis (2/15/19) Page | 1

Eclectic Products LLC

Manufacturing Facility

101 Dixie Mae Drive

Pineville, Louisiana

eclecticproducts.com

Customer Service

1-800-349-4667

Technical Support

1-800-767-4667

Administration Office

Eugene, Oregon

1-800-693-4667

ISO 9001:2015

Compliant

Quality Management Systems

UNITED STATES/

MEXICO

Pint Kit

Quart Kit

Gallon Kit

Not all styles/sizes/colors available in

all areas.

PRODUCT DESCRIPTION

FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING is an ultra-clear epoxy that

dries to a high gloss finish. It’s versatile enough for use on almost any surface – smooth

or rough, stained or painted, old or new. This easy-to-use, 1:1 ratio is ideal for

household and craft projects - just one pour equals 70 coats of varnish.

WHERE TO USE / APPLICATIONS

This ultra-clear, high gloss finishing epoxy is ideal for home improvement and craft

projects.

- coat tables, clocks, game boards and furniture

- imbed coins, rocks, sea shells, flowers or any non-waxy material

- preserve pictures, photographs, posters, signs and ceramics

FEATURES AND BENEFITS

HIGH BUILD EPOXY – Just one pour equals 70 coats of varnish

EASY TO USE – Easy 1:1 mixing ratio (by volume)

VERSATILE

– May be used on any non-waxy material.

SELF-LEVELING – Minimal spreading and maintenance required

TECHNICAL INFORMATION

PROPERTIES

Natural color:

Clear

Tensile strength:

450 psi

Tear strength:

200 psi

Shear strength:

200 psi

Compressive strength:

800 psi

Compressive strain:

75%

Elongation:

15%

Shore hardness:

85D

Solids content:

100%

VOC:

7.7 g/l as mixed

Viscosity (Side A Resin):

>1,450

Viscosity (Side B Hardener):

850-1,150

Viscosity (Mixed):

1,100

Mixing ratio:

1 to 1 by volume

Pot life (working time):

30 minutes @ 70 °F / 21 °C

Tack free time:

12 hours @ 70 °F / 21 °C

Cure time:

72 hours (depending on temperature)

Weight/gallon:

Part A (Resin): 9.63 / Part B (Hardener): 7.93 @ 77 °F /

25 °C (ASTM D-1475)

Application temperature:

70 to 80 °F (21 to 27 °C)

Service temperature:

10 to 120 °F (-12 to 49 °C)

Storage temperature:

Do not store above 95 °F (35 °C); if materials are hot

bring them to room temperature (77 °F / 25 °C) before

mixing.

Food Safety:

Glaze Coat is not classified as “Food Grade” or “Food

Safe” for direct food serving or storage by the FDA.

Properly cured Glaze Coat surfaces are safe to serve and

store food on so long as the food is contained in or on a

plate/container intended for direct food use. Heating,

serving, and storage of food directly on a Glaze Coat

surface is not recommended.

Summary of content (7 pages)

PAGE 1
Technical Data Sheet FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING PRODUCT DESCRIPTION Eclectic Products LLC Manufacturing Facility 101 Dixie Mae Drive Pineville, Louisiana eclecticproducts.
PAGE 2
Technical Data Sheet CANADA 0.94 L Kit 3.78 L Kit Not all styles/sizes/colors available in all areas. AUSTRALIA/NZ 0.47 L Kit 0.94 L Kit 3.78 L Kit Not all styles/sizes/colors available in all areas. FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING Shelf life: Freeze/Thaw Stability: 2 years (unopened - in package) Yes. Glaze Coat will freeze below the freezing point of water. Once re-melted at room temperature, it will return to normal physical properties. Coverage Pint Kit (0.47 L) 3.2 sq ft (0.
PAGE 3
Technical Data Sheet FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING SEAL COATS: For porous surfaces, a sealer coat of a WATER-BASED clear coat or thin coat of Glaze Coat prior to a flood coating is recommended. Certain woods with open grains such as oak and walnut will allow air to escape causing bubbles. Porous fabrics, papers or concrete should follow these steps as well. Mix about ¼ the amount normally used for a full flood coat and spread it thinly over entire surface. THIS WILL SEAL AIR PASSAGES.
PAGE 4
Technical Data Sheet FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING you can pour and spread at one time. STEP 4: SURFACE BUBBLES Surface bubbles MUST be removed when surface is still wet, not once surface begins the curing process or else bubbles will turn into dimples. Use a heat gun, blow dryer, small handheld propane torch or butane torch to remove bubbles. Keep flame 6 to 8 inches above surface (8 to 10 inches for heat guns) and use a slow, sweeping motion.
PAGE 5
Technical Data Sheet FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING • COATING CRAFT PROJECTS - Glaze Coat provides a thick coating to most substrates. See "Surface Preparation" section and complete steps 1 through 3. Mix enough Glaze Coat to coat your craft project (approximately 1/16” thick). Complete steps 4 and 5. Embed any desired items then repeat steps 1 through 5 until the desired coating thickness is achieved (see “Embedding Items” section). Complete step 6.
PAGE 6
Technical Data Sheet FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING • • • LIQUID DYES, FOOD DYES & WATER-BASED INKS: Produce a semi-transparent coating when using in thin coat applications (approx. 1/8” and under). ACRYLIC/WATER-BASED PAINT: Acrylic and water-based pigments can be used. Some disperse better than others. Color saturation is dependent on the color and brand used. Water-based paints sometime produce more bubbles due to the water throughout the mixture.
PAGE 7
Technical Data Sheet FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING LIMITED WARRANTY The product is warranted against any defect in materials or workmanship under normal use for a period of 180 days after the date of purchase. The product is also warranted under any implied warranties provided under applicable law, including, without limitation, the implied warranty of merchantability and the implied warranty of fitness for a particular purpose, for a period of 180 days after the date of purchase.