HUGH™44 CEILING FAN HUGH™52 CEILING FAN MODEL #FPS8332** MODEL #FPS8355** Español p. 18 ATTACH YOUR RECEIPT HERE READ AND SAVE THESE INSTRUCTIONS Purchase Date FPS8332** Net Weight 13.89 lbs (6.30 kg) FPS8355** Net Weight 16.53 lbs (7.50 kg) Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.
Important Safety Instructions WARNING: To avoid fire, shock and serious personal injury, follow these instructions. 1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally.
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan Tools Needed for Assembly Materials Wiring outlet box and box connectors must be of type required by local code. The minimum wire would be a 3conductor (2-wire with ground) of the following size: Four wire connectors (supplied) Installed Wire Length WARNING Up to 50 ft. 50 - 100 ft.
Energy Efficient Use of Ceiling Fans Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance. Using the Ceiling Fan Year Round Summer Season: Use the ceiling fan in the counterclockwise direction. The airflow produced by the ceiling fan creates a wind-chill effect, making you “feel” cooler. Select a fan speed that provides a comfortable breeze, lower speeds consume less energy.
Electrical and Structural Requirements (Continued) Deep box with brace (Figure 3) Paired with a deep box, this hanger is meant to span between two joists and takes the place of wooden blocking. CEILING JOIST WARNING To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked acceptable for fan support of 15.9 kg (35 lbs) or less and use mounting screws provided with the outlet box.
How to Hang Your Ceiling Fan WARNING Ceiling The fan must be hung with at least 7´ of clearance from floor to blades. (Figure 1) WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation.
How to Hang Your Ceiling Fan (continued) 4. Hang the Motor Assembly as shown. (Figure 5) You can now proceed with the electrical wiring of your fan. Ceiling Bracket Assembly Motor Assembly NOTE: Supply wires omitted for clarity Figure 5 How to Wire Your Ceiling Fan - Wall Control If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.
How to Install Your Wall Control 1. Carefully push all connected wires inside wall switch box. Secure the wall-mounted control to the outlet box with two screws provided. Then, the face plate attaches the wall control with two painted screws. (Figure 1) Screw Fan Speed Switch Light Switch Outlet Box Figure 1 How to Wire Your Ceiling Fan 1.
How to Assemble Your Ceiling Fan 1. Assemble the motor assembly to ceiling bracket using the previously removed screws and securely tighten all screws. (Figure 1) Ceiling Bracket Assembly Motor Assembly Figure 1 2. Push the canopy trim ring up to conceal the screws, such that the mounting tabs seat into the dimpled grooves in the ceiling bracket midway between the screws.
How to Assemble Your Light Kit 1. Remove one of the three screws in the support bracket at the bottom of the motor assembly and retain the screw for later. Slightly loosen the remaining two screws. (Figure 1) Figure 1 2. Assemble the light kit assembly to the support bracket using the two key slots in the light kit assembly. Replace the third screw and securely tighten all three screws. (Figure 2) Motor Motor Figure 2 Light Kit Assembly 3.
How to Assemble Your Light Kit (continued) 6. Remove the three screws in the upper LED plate assembly and retain the screws for later. (Figure 6) Upper LED Plate Assembly Figure 6 7. If you want to install the light kit, skip the step Assemble the light kit wire cover to the upper LED plate assembly using the preousily removed screws and securely tighten all three screws. (Figure 7) Upper LED Plate Assembly Light Kit Wire Cover Figure 7 8A.
How to Operate Your Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. (Figure 1) WARNING MAIN FUSE BOX Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until the blades are in place. Noise and fan damage could result. Figure 1 2.
Trouble Shooting WARNING For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble 1. FAN WILL NOT START Probable Cause Suggested Remedy 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. 2. Check line wire connections to fan and switch wire connections in the switch housings.
Parts List Model #FPS8332** & FPS8355** Ref.
FPS8332** Exploded-View Illustration 1 11 2 3 11 4 5 7 11 8 6 9 Figure 1 NOTE: 15 10
FPS8355** Exploded-View Illustration 1 11 2 3 4 11 5 7 11 8 6 9 Figure 1 NOTE: 16 10
10983 Bennett Parkway Zionsville, IN 46077 Phone: 888-567-2055 Outside U.S.: 317-733-4113 FAX: 866-482-5215 FANIMATION.COM 2016/06 V.
VENTILADOR DE TECHO HUGH™44 VENTILADOR DE TECHO HUGH™52 MODELO #FPS8332** MODELO #FPS8355** Adjunte su recibo AQUÍ LEA Y GUARDE ESTAS INSTRUCCIONES Fecha de compra FPS8332** Peso neto 6.30 kgs (13.89 lbs) FPS8355** Peso neto 7.50 kgs (16.53 lbs) Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro Departamento de Servicio al Cliente al 1-888-567-2055, 8 a.m. - 5 pm, hora del Este, de lunes - viernes.
Instrucciones de seguridad importantes ADVERTENCIA: Siga estas instrucciones para prevenir incendios, descargas eléctricas y lesiones personales graves. 1. Lea el manual del propietario y la información de seguridad antes de instalar su nuevo ventilador. Observe los diagramas de ensamblaje adjuntos. 2. Antes de llevar a cabo el mantenimiento o la limpieza de la unidad, desconecte la electricidad en el panel de servicio y bloquee los medios de desconexión del mismo para evitar que se active accidentalmente.
Este manual está diseñado para facilitar al máximo el ensamblaje, la instalación, el funcionamiento y el mantenimiento de su ventilador de techo. Herramientas necesarias para el ensamblaje Materiales La caja de distribución eléctrica y los conectores de la caja deben ser del tipo requerido por el código local. El cable más pequeño debe ser un cable de tres conductores (de dos conductores con conexión a tierra) del siguiente tamaño: tamaño del cable según el A.W.G.
r v El nivel de rendimiento y ahorro de energía de los ventiladores de techo dependen de su correcta instalación yuso.Acontinuaciónlepresentamosalgunassugerencias para asegurar un rendimiento eficiente del producto. r cho Uso del ventilador de techo todo el año En verano: Use el ventilador de techo en sentido contrario a las agujas del reloj. El flujo de aire que produce el ventilador creará un efecto frío del aire que lo refrescará más.
Requisitos eléctricos y estructurales (cont.) Uso del soporte (Figura 3) Conectado a una caja de distribución eléctrica, este colgador sirve para abarcar el espacio entre dos vigas y ocupar el lugar de bloqueo de la madera. Vigas del techo ADVERTENCIA Para reducir el riesgo de incendios, descargas eléctricas o lesiones personales, fije el ventilador a la caja de distribución eléctrica marcada como aceptable para soporte de ventilador de 15,88kg (35lb).
Cómo colgar el ventilador de techo ADVERTENCIA Techo Las aspas del ventilador deben estar suspendidas, al menos, a 2 m (7´) del piso (Figura 1) ADVERTENCIA Para evitar posibles descargas eléctricas, asegúrese de que la electricidad esté desconectada en la caja de fusibles principal antes de colgar el ventilador.
Cómo colgar el ventilador de techo (cont.) 4. Introduzca la unidad del motor en la unidad del soporte del techo tal y como se muestra en la ilustración. (Figura 5) Ahora puede continuar con las instrucciones para realizar la instalación eléctrica de su ventilador. Unidad de soporte de techo Motor NOTA: Se omiten los cables de suministro para mayor claridad.
Cómo instalar su mando a distancia 1. Asegure el control instalado en la pared en la caja de conexiones con los dos tornillos suministrados. A continuación, la placa frontal fija el control de pared con los dos tornillos pintados. (Figura 1) Tornillo Interruptor de velocidad de ventilador Interruptor de iluminación Caja de conexiones Figura 1 Cómo realizar la instalación eléctrica del ventilador de techo 1.
Cómo ensamblar el ventilador de techo 1. Instale la unidad del motor a la unidad de soporte de techo utilizando los tornillos retirados previamente fije con seguridad los tres tornillos. (Figura 1) Unidad de soporte del ventilador Motor Figura 1 2. Presione hacia arriba el anillo de la cubierta de tornillos para ocultar los tornillos. Así, las pestañas de montaje se coloquen en las ranuras con muescas ubicadas en la cubierta del techo entre los tornillos.
Cómo ensamblar su el kit de iluminación 1. Guárdelos para después y afloje levemente los otros dos tronillos. (Figura 1) Figura 1 2. Instale la ensamble de la placa de iluminación en el soporte utilizando las dos ranuras principales de conexión. Vuelva a colocar el tercer tornillo y asegure los tres tronillos. (Figura 2) Motor Motor Figura 2 Ensamble de la placa de iluminación 3. Extraiga uno de los tres tornillos del ensamble de la placa de iluminación y guárdelos para paso 5.
Cómo ensamblar los kit de luz (cont.) 6. Extraiga los tres tornillos del Unidad de placa LED superior y Guárdelos para después. (Figura 6) Unidad de placa LED superior Figura 6 7. Si desea instalar el kit de iluminación, sáltese este paso. Instale la cubierta del cable del kit de iluminación en la unidad de placa LED superior utilizando los tornillos retirados previamente fije con seguridad los tres tornillos.
Cómo utilizar su ventilador de techo 1. Restaure la fuente de alimentación de la toma de corriente enciendo la electricidad del fusible principal. (Figura 1) ADVERTENCIA PRINCIPAL CAJA DE FUSIBLES Compruebe que todas las conexiones realizadas correctamente, incluyendo la toma de tierra, y que no se visualizan ningún cable pelado en los conectores de cables, con la excepción del cable de toma de tierra.
Solución de problemas ▲ADVERTENCIA Para su propia seguridad, desconecte la electricidad de la caja de fusibles o disyuntor antes de solucionar problemas en su ventilador. Problema 1. EL VENTILADOR NO ARRANCA Causa posible Solución sugerida 1. El fusible o el disyuntor están fundidos. 1. Controle los fusibles del circuito principal y derivado o los disyuntores. 2. Las conexiones eléctricas del ventilador o del interruptor en la caja del interruptor están flojas. 2.
Lista de piezas Modelos N.°FPS8332** & FPS8355** N.° de Ref. 1 Descripción FPS8332** Pieza # N.° FPS8355** Pieza # N.
Modelo N.
Modelo N.
10983 Bennett Parkway Zionsville, IN 46077 Llame sin cargo al (888) 567-2055 FAX (866) 482-5215 Desde fuera de los EE.UU., llame al (317) 733-4113 Visite nuestro sitio Web en www.fanimation.com 2016/06 V.