Chapter 2: Specifications Page 2-1
Chapter 2: Specifications 2.1 (Rev. 8/98) System Specifications { Power Supply Voltage P 200~230 VAC ±10%, 3-Phase, 50/60 Hz { Installation Requirement P NEMA 12 enclosure { Range of Operation P Duty cycle below 50% (reference Section 2.2 Duty Cycle Calculation) P Additional specifications will be provided for nutrunners greater than 50 kgm.
Chapter 2: Specifications 2.2 (Rev. 8/98) Duty Cycle Calculation The rated duty cycle for the AFC1100 System is calculated as follows: Tool Rotation Time X 100 = Duty Cycle Percentage (%) Total Cycle Time (Tool Rotation + Tool Waiting) Example: Tool Rotation Time = Total Cycle Time = 3 Seconds 12 Seconds x 100 = 25% Duty Cycle Percentage Duty cycle ratings vary between tools. As a general rule, however, it should not exceed 50%. Refer to the specifications for each tool.
Chapter 2: Specifications 2.3 (Rev. 8/98) User Console Requirements (Customer Supplied) Specification is based on proposed future software upgrades. The current DOS based software has less requirements. { CPU: Minimum 80486-75MHZS microprocessor { DATA Communication: RS422 Port or RS232 port with an RS422 converter Centronics Parallel Port { FLOPPY DISK Drive: 3.5" 1.
Chapter 2: Specifications 2.4 (Rev. 8/98) Axis Unit { AXIS UNIT TYPE TOOL MOTOR TYPE TOOL MOTOR MODEL NUMBER TOOL MOTOR RATING AXIS UNIT PEAK CURRENT AXIS UNIT IN-RUSH CURRENT AXIS UNIT INPUT POWER AXIS-103 M1 W1 AXIS-105 M2 M3 MFA006 BNE006- MFA010 MFA020 HA2NSA A117 HA2NSA HA2NSA AXIS-110 W3 M4 BXE020A912 MFA040 HA1NS 60W 70W 100W 200W 200W 400W .625A .
Chapter 2: Specifications 2.5 (Rev. 8/98) Nutrunner { Fastening accuracy (Torque): From 1/4 ~ full scale torque: 6 Less than 10% { Torque sample rate: Full Scale Torque X 1/1000 { Torque display resolution: 4 digit display with floating decimal point. { Fastening accuracy (Angle): Within +1 degree { Angle sample rate: Below 0.036 degrees (dependent upon gear ratio). { Angle display resolution. 0.
Chapter 2: Specifications (Rev. 8/98) DFT-401M1-S/O AXIS-103 39.2 4.0 400 28.8 346 39.6 :1 250 3 DFT-401M2-S/O AXIS-103 39.2 4.0 400 28.8 346 19.8 :1 500 5 DFT-601M3-S/O AXIS-105 58.8 6.0 600 43.3 520 12.6:1 790 8 DFT-801M3-S/O AXIS-105 78.4 8.0 800 57.6 693 19.8 :1 500 5 DFT-132M3-S/O AXIS-105 127.4 13.0 1,300 94.0 1,127 25.2 :1 395 4 DFT-152M3-S/O AXIS-105 147.0 15.0 1,500 108.0 1,300 31.5:1 315 4 DFT-202M3-S/O AXIS-105 196.0 20.
Chapter 2: Specifications (Rev. 8/98) 2.5.
Chapter 2: Specifications (BLANK PAGE) Page 2-9 (Rev.
