Data Sheet

3
I-2017, www.findernet.com
I
15
SERIES
15 SERIES
Dimmers
“Master + Slave” system for dimming multiple
lighting loads of either single or mixed lamp
technologies
Type 15.10 “Master“ - accepts input from a
controlling push-button and outputs a dimming
signal to a maximum of 32x15.11 slave dimmers,
or other drivers or luminaires accepting a
standardised 0-10V/1-10V signal
- Use with 4 wire connection
- “Soft” On and Off transitions
- Linear dimming
- Selectable operating modes with or without
previous light level memory
- Staircase timer function
Type 15.11 “Slave“ - accepts 1-10V input from a
15.10 or other 0-10V/1-10V output device to dim
a wide variety of lamps of different technology
- Selector switch for incandescent and halogen
lighting loads (with or without transformer or
electronic driver)
- Compatible with energy saving dimmable
CFL or LED lamps and with all types of
electromagnetic transformers
- Thermal protection against overload, thermo-
fuse for extreme or short-circuit protection
Screw terminal
15.10 15.11
“Master” dimmer
• 0-10V/1-10V output to drive
up to 32x15.11 slave dimmers
or other similar devices
• Multi-function (with or without
memory, including special “CFL
with memory” function)
• Linear dimming
• Dimming speed setting
• Staircase timer function, with
switch-off "early warning”
signalled by lamps dimming
• 230VAC supply, 50/60Hz with
automatic adjustment for
frequency
• 6A output relay contact*
• 17.5mm wide, modular,
35mm rail mount
“Slave” dimmer
• 1-10V input, driven by 15.10 or
by other 0-10V/1-10V output
devices
• Maximum lamp load 400W
• 100W load with energy saving
dimmable lamps (LED and CFL)
• Leading and trailing edge
dimming methods
• “Transformer” function (for
use with electromagnetic
transformers)
• Minimum dimming level
setting
• 17.5mm wide, modular, 35mm
rail mount
* Maximum peak current of the contact
30A 230VAC. Use a contactor or power relay to
switch loads exceeding this value
For outline drawing see page 11
“Master Dimmer” output specifications
Driving signal (Output mode automatically
configures to match input mode of the
connected Driver)
0-10V, +35mA max
(Active current sourcing mode)
—
1-10V, –35mA max
(Passive current sinking mode)
—
Contact configuration A 1 NO (6A/230VAC)* —
“Slave Dimmer” output specifications
Power max. W — 400
Power min. W — 3
Nominal lamp ratings:
230V incandescent or halogen W
— 400
(1)
Toroidal electromagnetic transformers
for LV halogen W — 400
(2)
E-core electromagnetic transformers
for LV halogen W — 400
(2)
Electronic transformers (or ballasts)
for LV halogen W — 400
(1)
Dimmable compact fluorescent (CFL) W — 100
(3)
Dimmable 230V LED W — 100
(3) or (1)
Dimmable electronic transformers
for LV LED W — 100
(1)
Supply specification
Nominal voltage (U
N
) VAC (50/60Hz) 110…230 230
Operating range (0.8…1.1)U
N
(0.8…1.1)U
N
Stand-by power consumption W 0.5 0.5
Dimming operating modes
—
Trailing edge (
)
Leading edge ( ) and ( )
Technical data
Dimming speed (total dimming time) s 1.5…10 —
Delay setting (staircase function) min 0.5…20 —
Max no. of illuminated push-button (≤1mA) 15 —
Ambient temperature range °C –10…+50 –10…+50
(4)
Protection category IP 20 IP 20
Approvals (according to type)
Note
(1)
Select “trailing edge” ( ) position on the front selector.
(2)
Select “transformer” ( ) position on the front selector. Preferably, no more than 2 transformers.
(3)
Select “leading edge” ( ) position on the front selector, and set the appropriate minimum dimming value (dependent on lamp type).
(4)
With lamp load >300W (>75W for CFL or LED lamps), adequate ventilation must be provided - a gap of 9mm on both side of the dimmer is
suggested. Use the plastic separator type 022.09.