Kleurentelevisie Colour television FL4822SMART Télévision en couleur De handleiding Owner’s manual Manuel d'utilisateur
Contents Safety Information.................................................32 Markings on the Product.......................................33 Environmental Information....................................33 Features................................................................34 Accessories Included............................................34 Standby Notifications.............................................34 TV Control Switch & Operation.............................
• Ensure that no open flame sources, such as lit candles, are placed on top of the TV. • To prevent injuries, this TV must be securely attached to a wall by carefully following the instructions (if the option is available). • Occasionally, a few non-active pixels may appear on the screen as a fixed blue, green or red point. Please note that this does not affect the performance of your product. Take care not to scratch the screen with fingernails or other hard objects.
will be off in 15 seconds.” message will be displayed on the screen. Select Proceed and press OK to turn the screen off immediately. If you don’t press any button, the screen will be off in 15 seconds. Press any button on the remote or on the TV to turn the screen on again. Note: Screen Off option is not available if the Mode is set to Game. When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce energy consumption.
to select a menu tab and press OK to enter. Use the directional buttons again to select or set an item. Press Return/Back or Menu button to quit a menu screen. Information for Users on Disposal of Old Equipment and Batteries Input Selection Once you have connected external systems to your TV, you can switch to different input sources. Press the Source button on your remote control consecutively to select the different sources.
Remote Control 1. Standby: Switches On / Off the TV 2. TV: Displays channel list / Switches to TV Source 3. Volume +/- 4. Menu: Displays TV menu 5. OK: Confirms user selections, holds the page (in TXT mode), views channel list (DTV mode) 6. Back/Return: Returns to previous screen, opens index page (in TXT mode) Internet: Opens the portal page, where you can reach many web based applications 7. TV 8. My button 1 (*) 9. Source: Shows all available broadcast and content sources 10.
Connections Connector Type Cables Device Scart Connection (back) VGA Connection (back) SIDE AV PC/YPbPr Audio Connection (side) YPbPr/PC Audio Cable (not supplied) HDMI Connection (back) SPDIF SIDE AV SPDIF (Optical Out) Connection (back) Side AV (Audio/Video) Connection (side) HEADPHONE Headphone Connection (side) YPBPR YPbPr Video Connection (back) AV Cable (not supplied) PC to YPbPr Connection Cable (not supplied) NOTE: When connecting a device via the YPbPr or Side AV input, you must use
channels of it will be listed on the top of the Channel List. When finished, press OK to continue. Switching On/Off To Switch the TV On Connect the power cord to a power source such as a wall socket (220-240V AC, 50 Hz). To switch on the TV from standby mode either: • Press the Standby button, Programme +/- or a numeric button on the remote control. • Press the side function switch on the TV until the TV comes on from standby.
Wait a little while before each plugging and unplugging as the player may still be reading files. Failure to do so may cause physical damage to the USB player and the USB device itself. Do not pull out your drive while playing a file. You can use USB hubs with your TV’s USB inputs. External power supplied USB hubs are recommended in such a case. It is recommended to use the TV’s USB input(s) directly, if you are going to connect a USB hard disk.
selection) during the First Time Installation use the PIN that you have defined. IMPORTANT: Formatting your USB drive will erase ALL the data on it and it’s file system will be converted to FAT32. In most cases operation errors will be fixed after a format but you will lose ALL your data. If “USB disk writing speed too slow to record” message is displayed on the screen while starting a recording, try restarting the recording.
TV Menu Contents System - Picture Menu Contents Mode You can change the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: Cinema, Game(optional), Sports, Dynamic and Natural. Contrast Adjusts the light and dark values on the screen. Brightness Adjusts the brightness values on the screen. Sharpness Sets the sharpness value for the objects displayed on the screen. Colour Sets the colour value, adjusting the colours.
System - Sound Menu Contents Volume Adjusts the volume level. Equalizer Selects the equalizer mode. Custom settings can be made only when in User mode. Balance Adjusts whether the sound comes from the left or right speaker. Headphone Sets headphone volume. Please ensure before using headphones that the headphone volume is set to a low level, to prevent damage to your hearing. Sound Mode You can select a sound mode (If the viewed channel supports).
Menu Timeout Changes timeout duration for menu screens. Software Upgrade Ensures that your TV has the latest firmware. Press OK to see the menu options. Application Version Displays current software version. Subtitle Mode This option is used to select which subtitle mode will be on the screen (DVB subtitle / Teletext subtitle) if both is available. Default value is DVB subtitle. This feature is available only for the country option of Norway.
Internet Lock: If this option is set to ON, the open browser application in the portal will be disabled. Set to OFF to release the application again. General TV Operation Using the Channel List The TV sorts all stored stations in the Channel List. You can edit this channel list, set favourites or set active stations to be listed by using the Channel List options. Press the OK/TV button to open the Channel List.
Event Details (Info button): Displays detailed information about selected events. Filter (Text button): Views filtering options. Next Time Slice (Green button): Displays the events of next time slice. Options (OK button): Displays event options. Rec./Stop (Record button): The TV will start to record the selected event. You can press again to stop the recording. IMPORTANT: Connect a USB disk to your TV while the TV is switched off. You should then switch on the TV to enable the recording feature.
Remote control - no operation Software Upgrade Your TV is capable of finding and updating the firmware automatically via the broadcast signal or via Internet. • The batteries may be exhausted. Replace the batteries. Software upgrade search via user interface Input sources - can not be selected On the main menu select System>Settings and then More. Navigate to Software upgrade and press the OK button.
PC Input Typical Display Modes AV and HDMI Signal Compatibility The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions.
Supported Video File Formats for USB Mode Extension Video Codec .dat, vob MPEG1/2 MPEG1/2, MPEG4 MPEG1/2, H.264, AVS, MVC .mpg, .mpeg .ts, .trp, .tp SPEC (Resolution) & Bit Rate .mp4, .mov, .3gpp, .3gp MPEG1/2, MPEG4, H.263, H.264, Motion JPEG .avi MPEG1/2, MPEG4, Sorenson H.263, H.263, H.264, WMV3, Motion JPEG .mkv MPEG1/2, MPEG4, H.263, H.264, WMV3, Motion JPEG .asf Sorenson H.263, H.264, WMV3, Motion JPEG .flv .swf .wmv WMV3 RV30/RV40 1080P@30fps - 40 Mbps H.264: 1080Px2@30fps - 62.
Supported Audio File Formats for USB Mode Extension .mp3, .avi .asf .mkv, .mka .ts, .trp, .tp, .dat, .vob, .mpg, .
Extension .wav .3gpp, .3gp, .mp4, .mov, .m4a .flv .ac3 .swf .ec3 .rm, .rmvb, .ra .wma, .wmv .webm Audio Codec Bit Rate Sample rate MPEG1/2 Layer1 MPEG1/2 Layer2 MPEG1/2 Layer3 LPCM IMA-ADPCM, MS-ADPCM G711 A/mu-law MPEG1/2 Layer3 AC3 EAC3 AAC, HEAAC VORBIS LPCM IMA-ADPCM, MS-ADPCM G711 A/mu-law MPEG1/2 Layer3 AAC, HEAAC AC3 AAC, HEAAC MPEG1/2 Layer3 EAC3 AAC, HEAAC 32Kbps ~ 448Kbps 8Kbps ~ 384Kbps 8Kbps ~ 320Kbps 64Kbps ~ 1.
Supported DVI Resolutions When connecting devices to your TV’s connectors by using DVI converter cable(DVI to HDMI cable - not supplied), you can refer to the following resolution information.
Connectivity network wall socket Wired Connectivity To Connect to a Wired Network • You must have a modem/router connected to an active broadband connection. • Ensure that Nero Media Home software is installed to your PC (for Audio Video Sharing function). See “Nero Media Home Installation” section. • Connect your PC to your modem/router. This can be a wired or wireless connection. • Connect your TV to your modem/router via an ethernet cable. There is a LAN port at the rear (back) of your TV.
If the selected network is protected with a password, please enter the correct key by using the virtual keyboard. You can use this keyboard via the directional buttons and the OK button on the remote control. Broadband ISP connection Wait until the IP address is shown on the screen. This means that the connection is now established. To disconnect from a wireless network, highlight Network Type and press Left or Right buttons to set as Disabled. A Wireless-N router (IEEE 802.
Then press the Source button on the remote and switch to Wireless Display source. A screen appears stating that the TV is ready for connection. Open the sharing application on your mobile device. These applications are named differently for each brand, please refer to the instruction manual of your mobile device for detailed information. Scan for devices. After you select your TV and connect, the screen of your device will be displayed on your TV.
If you select the media type as Videos and choose a device from the selection menu. Then select the folder with video files in it on the next screen and all the available video files will be listed. To play other media types from this screen, you can go back to main Media Browser screen and select the media type as desired and then perform the network selection again. Or press the Blue button to switch to next media type quickly without changing the network.
Internet Browser To use the internet browser, please select the internet browser logo from the portal section. (*)The appearance of the browser logo may change Refresh Home Page Address Bar Add History Bookmarks Zoom Previous Next Settings App App App App App App App App App Remote control shortcuts (Zoom in-out/Back/Home) • To navigate the web browser, use the arrow buttons on the remote control. Press OK to continue.
Smart Center Smart Center is a mobile application running on iOS and Android platforms. With your tablet or phone, you can easily stream your favourite live shows and programmes from your smart TV. Also; you can launch your portal applications, use your tablet as a remote control for your TV and share media files. Note: Being able to use all functions of this application depends on the features of your TV.
FollowMe TV Feature (if available) Tap on the FOLLOW ME TV widget located at the bottom left of the screen of your mobile device to change the layout for FollowMe TV feature. Tap the play icon to start streaming of the content from the TV to your mobile device. Available if your device is in your routers operation range. Notes: Note that only digital(DVB-T/C/S) SD channels are supported. Multilanguage audio support and subtitle on/off features are not functional.