Installation Instructions

ManualsBrandsFire Magic ManualsBarbecue14 Inch Built-In Single Searing Station with 900-¦ Infrared Heat from 24,400 BTU Infrared Burner: Liquid Propane

SAFETY WARNINGS & CODES

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

INSTALLATION AND OPERATING

INSTRUCTIONS

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

DANGER

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid if equipped.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or ﬁ re department.

WARNING

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

2. A propane cylinder not connected for use

shall not be stored in the vicinity of this or

any other appliance.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

CODE AND SUPPLY REQUIREMENTS: This

unit must be installed in accordance with local

codes and ordinances, or, in the absence of local

codes, with either the latest National Fuel Gas

Code (ANSI Z223.1/NFPA 54), or Natural Gas

and Propane Storage and Handling Installation

Code (CSA-B149.1).

This appliance and its individual shutoff valves

must be disconnected from the gas-supply piping

system when testing the system at pressures in

excess of

psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its individual

manual shutoff valves during any pressure testing

of the gas-supply system at pressures up to and

including

psig (3.5 kPa).

All electrical outlets in the vicinity of the unit must

be properly grounded in accordance with local

codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

WARNING

Improper installation, adjustment, alteration,

service, or maintenance can cause injury or

property damage. Refer to this manual. For

assistance or additional information, consult a

qualiﬁ ed professional installer, service agency,

or the gas supplier.

Certiﬁ ed to: ANSI Z21.58-2007

CSA 1.6-2007

09-41

L-C2-380

Rev 1 - 1401131425

32874-1(P)

SEARING STATION

diamond series

Summary of content (16 pages)

PAGE 1
SEARING STATION diamond series 32874-1(P) INSTALLATION AND OPERATING INSTRUCTIONS INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference. SAFETY WARNINGS & CODES IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE. WARNING DANGER IF YOU SMELL GAS: 1. 2. 3. 4. 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2.
PAGE 2
STATION DESSÉCHANTE SÉRIE DE DIAMANT 32874-1(P) INSTALLATION ET CONSIGNES D’UTILISATION INSTALLATEUR : Laissez ces instructions avec le consommateur. CONSOMMATEUR : Maintenez pour la future référence. AVERTISSEMENTS ET CODES DE SÛRETÉ IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION DANGER: AVERTISSEMENT: S’il y a une odeur de gaz: 1. Coupez l’admission de gaz de l’appareil. 2. Éteindre toute flamme nue. 3. Ouvrir le couvercle. 4.
PAGE 3
TABLE OF CONTENTS 1 3 3 3 4 5 5 5 5 6 6 6 7 7 7 10 11 11 11 11 11 13 15 15 16 SAFETY WARNINGS & CODES TABLE OF CONTENTS CAUTION PRODUCT DATA TABLE PARTS LIST PLANNING FOR INSTALLATION OF THE SEARING STATION WHERE TO INSTALL THE SEARING STATION ENSURING PROPER COMBUSTION AIR AND COOLING AIRFLOW EXHAUST REMOVAL INSTALLATION GAS-SUPPLY PLUMBING REQUIREMENTS CHECKING FUEL AND ORIFICES CONVERTING THE REGULATOR CONNECTING THE GAS SUPPLY POWER SUPPLY FOR IGNITION AND LIGHTED KNOBS POWER SUPPLY (MULTIPLE ACCESSORY
PAGE 4
PART S L IST Item Description Part No. Qty. 1. Cover 3287-07 1 2. Stainless-steel grid 3551-S 1 3. Burner assembly with ignitor 4. Stainless-steel control panel assembly 23287-09 1 5. Valve manifold assembly 3287-22 1 6. Control knob 24182-42 1 7. Lighted bezel assembly 24182-44 1 8. Drip tray assembly with match holder 3085 1 9. Regulator PR-4 1 10. Light Switch 24182-46 1 11. Infrared burner wire 3199-71 2 12. Extension wire kit ‡ 23278-12 1 1 13.
PAGE 5
PLANNING FOR INSTALLATION OF THE SEARING STATION WHERE TO INSTALL THE SEARING STATION FOR OUTDOOR USE ONLY WARNING: The unit must have a minimum of 18" right, left, and back clearance from unprotected combustible construction such as wood, plastic, or stucco with wood framing. If installing this unit in a combustible surround, the correct R.H. Peterson insulating liner must be used. Do not install this unit under unprotected flammable surfaces.
PAGE 6
INSTALLATION GAS-SUPPLY PLUMBING REQUIREMENTS Rigid 1/2" black steel pipe is required to conduct the gas supply into the masonry opening for connection to the unit. Apply pipe joint compound (resistant to all gasses) to all male pipe fittings and tighten all joints securely. Do not use pipe joint compound to connect flare fittings. The pipe should enter the enclosure either from the bottom or from any side at least 13" below the countertop.
PAGE 7
INSTALLATION ( Co n t .) CONVERTING THE REGULATOR 1. Unscrew and remove the cap from the regulator, extracting the converter (Fig. 7-1). Regulator Note the cap on top 2. Remove the converter (the plastic stalk) by carefully pulling it away from the center of the cap (it will snap out of its seating); see Fig. 7-2. 3. Turn the converter around and replace it carefully into the center of the cap (it will snap into place).
PAGE 8
INSTALLATION ( Co n t .) c. Connect the 2 extension ground wires to the grill and power supply box ground wires AS SHOWN in Fig. 8-3. To install using the wire extension: Locate the power supply box inside of the island enclosure. Disconnect the power cord. a. Disconnect the grill (male) molex connection from the master switch harness. Disconnect the grill ground wire from the power supply box. (See Fig. 8-1) Master switch harness CONNECT Power supply box Fig. 8-3 Grill molex connection d.
PAGE 9
INSTALLATION ( Co n t .) Note: Each side of the unit has a tab just behind the control panel. These tabs prevent the control panel from moving inward. If the tabs interfere with the unit sliding in (see Fig. 9-1), use pliers to bend them inward so that they clear the enclosure sides. Leave the tabs slightly out to ensure they still keep the control panel from moving inward (see Fig. 9-2). To install using a power supply box: a.
PAGE 10
INSTALLATION ( Co n t .) POWER SUPPLY (MULTIPLE ACCESSORY UNITS) The previous section covers in detail how to individually connect this accessory unit to an Echelon grill power supply box. If multiple accessory units are to be installed, the following diagrams will assist in their installation.
PAGE 11
GENERAL INFORMATION SAFETY TIPS IN USING THE SEARING STATION Each time you use the Searing Station, ensure that: 1. The area around the unit is clear and free from flammable vapors, liquids, and other combustible materials. 2. There is no blockage of airflow around the burner. 3. When using propane gas, ensure that: a. The special ventilation openings in the enclosure are kept free and clear of debris. b. If connected to a propane cylinder, inspect the rubber hose attached to the regulator before each use.
PAGE 12
UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE IMPORTANT POUR VOTRE SÛRETÉ LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE. En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.
PAGE 13
SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS IMPORTANT FOR YOUR SAFETY READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER. When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION. CYLINDER/CONNECTOR REQUIREMENTS a. Propane-gas cylinders, valves, and hoses must be maintained in good condition and must be replaced if there is visible damage to either the cylinder or valve.
PAGE 14
ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE) Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le unité. ÉCLAIRAGE ÉLECTRONIQUE Note: ÉCLAIRAGE MANUEL Le unité doitélectronique être relié à la puissance 120VAC pour L’éclairage exige une batterie installée l’éclairage électronique. de 9 volts avec une bonne charge. RRN O SUTU TO ATTENTION: Attendez toujours cinq (5) minutes le gaz pour se dégager après que n’importe quelle 1.
PAGE 15
LIGHTING (IGNITION) INSTRUCTIONS Read all instructions before lighting, and follow these instructions each time you light the unit. ELECTRONIC LIGHTING MANUAL LIGHTING Grill must be connected to 120VAC power for Note: Electronic lighting requires an installed 9-volt electronic lighting. battery with a good charge. 1. Open lid(s) or remove cover(s) from burner(s) to be lit. CAUTION: Always wait five (5) minutes for gas to clear after any unsuccessful lighting attempt. 2.
PAGE 16
WARRANTY PETERSON FIRE MAGIC GRILLS AND ACCESSORIES LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Fire Magic® grill to be free from defects in material and workmanship. Fire Magic® cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are warranted for as long as you own your Fire Magic® grill -- LIFETIME. (Except as noted below.) Fire Magic Choice stainless steel tubular burners are warranted for TWENTY (20) YEARS.