FREEZER FFR 100 INSTRUCTION BOOKLET 2222739-14 t
Important Safety Instructions These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation General Safety ¥ Check the appliance for transport damage. Under no circumstance should a damaged appliance be installed. In the event of damage please contact your retailer.
Servicing At the end of the Appliance Life ¥ This product should be serviced by an authorised engineer and only genuine spare parts should be used. ¥ Under no circumstances should you attempt to repair the appliance yourself. Repairs carrier out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Force Centre. ¥ When disposing of your appliance use an authorised disposal site.
Operation Before use Remove all securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5 ml to 0.5 litre of water). Do not use soap or detergent as the smell may linger. Dry thoroughly. Freezer controls 6 5 4 ➀ ➁ ➂➃ (1) Fast freeze switch (2) Fast freeze light (yellow) (3) Warning light (red) ➄ 1 2 3 ➅ (4) Pilot light (green) (5) Push button ON/OFF (6) Thermostat control knob Starting your appliance Insert the plug into the wall socket.
food to be frozen in the appliance's two top compartments; if freezing only a small amount of food, use the top compartment. Once the food is completely frozen (which could take up to 24 hours) return the fast freeze button to the ÇOFFÈ position; the yellow light (2) goes off. Distribute the frozen food packages in the other compartments, so that the top compartments can be used for a further freezing operation. Only freeze top quality, fresh and thoroughly cleaned foodstuffs.
Cold accumulator Ice making The freezer contains one cold accumulator which can be found in the top compartment. The cold accumulator increases storage times in the event of a power cut or breakdown. It must be placed on top of the food. Removal of this unit will increase the capacity of the fast freezing compartment but will reduce storage times in the event of a power cut or breakdown. Fill the ice tray 3/4 full with water to allow the ice to expand and place it in the freezer.
Defrosting The freezer compartment will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 1/4". During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out and it is advisable to carry out this operation when the appliance is empty.
Maintenance and Cleaning Warning Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Important This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Internal cleaning Periodic cleaning The appliance is equipped with a ventilation grid. Keep clean to guarantee good ventilation and good working order of the appliance.
Something not Working? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom Solution No power to appliance - Check there is power at the socket. - Check there is not a power cut by checking the household lights. - Check the fuse has not blown.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning:- 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Guarantee Conditions Standard guarantee conditions We, EHP, undertake that if within 12 months of the date of purchase this Firenzi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ¥ The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
Technical Specifications DIMENSIONS Height Width Depth 81,5 59,6 54 POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED AVERAGE DAILY UNITS ELECTRICITY (*) 220-240 V / 50 Hz 90 W 0,78 kWh GROSS CAPACITY 108 l NET CAPACITY 100 l cm cm cm STAR RATING (*)This figure is based on standard test results in accordance with European Standard EN153. Actual consumption will depend on how the appliance is used and where it is located.
Electrical Connection WARNING THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted. Remove the fuse from the cut off plug. The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13amp socket in another part of your home.
Door reversal To reverse the opening direction of the door, proceed as shown in the figures: 6 4 1 7 8 5 2 3 1 2 Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting.
Building-in instructions Before carrying out any work, remove the plug from the power socket. Building in the appliance under a worktop Grid preparation The dimensions of the recessed installation area must correspond with those indicated in the figure. Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). 60 0 5 min50 .
2. Push the appliance into place. The plug socket necessary for connection of the appliance to the electricity supply should be positioned, so that the plug is not placed in the recess. N.B. The joint cover (B) is to be assembled after having installed the appliance in the recess. 3. To adjust the height proceed as follows: - Loosen or tighten the two front feet. - The rear feet are adjusted by turning the screw in the front kick plate to the left or right. 2 596 1 B 5 55 x ma 3 - 2Li89 + 4.
6.
Fitting the plinth Important For the efficient operation of the appliance, it is important that the original ventilation grid is used. = 10 = ¥ For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. The same applies to an opening height dimension B=870 mm and a plinth height dimension b=150 mm.
922 822 673
