Manualshelf

Frameless Cabinetry Installation Guide

ManualsBrandsFisher & Paykel ManualsBuilt-In Bottom Freezer RefrigeratorsFisher & Paykel Panel Ready Built-In Bottom Freezer Refrigerator
31323334353637383940
30
!9 ATTACH BOTTOM GRILLES
For custom toe tick greater than 4” (102mm)
1
Measure the required height for the bottom grille. On a board, carefully score/cut
theun-required vanes from the bottom of the kickstrip grille and discard (refer to A).
2
Drill Ø5/32” (4mm) holes into the dimples of the grille (refer toB).
Repeat this process for all dimples.
2
Align the air flow divider underneath the grille tabs indicator and clip onto the vanes of the
bottom grille (refer to B).
3
With the grille tabs facing upwards, align the grille to the bottom of the plinth where the
screw holes are located and secure with screws x3 (#8 x 5/8” pan head screws) (refer to C).
4
Align the air flow divider underneath the grille tabs indicator and clip onto the vanes of the
bottom grille (refer to D).
For toe kick installation at 4” (102mm)
1
With the grille tabs facing upwards, align the grille clips to the bottom of the plinth’s slots,
then firmly push grille onto the plinth (refer to A).
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
B
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
Grille tabs
A
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
D
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
A
Cut un-required vanes from the bottom of the grille
B
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
Grille tabs
Front right view
DETAIL B
SCALE 2 : 5
C