G2579 Instructions TELESCOPE & PROJECTOR Please keep this instruction sheet for future reference, as it contains important information. Requires four “C” (LR14) alkaline batteries for operation (not included). Requires one KPR113 Krypton light bulb (included). Tool required for battery installation and light bulb replacement: Phillips screwdriver (not included). www. f is e pri c her- .
Battery Installation 1.5V x 4 “C” (LR14) Shown Actual Size • Locate the battery compartment door on the top of the toy. • Loosen the screw in the battery compartment door with a Phillips screwdriver. Lift the battery compartment. • Insert four “C” (LR14) alkaline batteries. Hint: We recommend the use of alkaline batteries for longer battery life. • Replace the battery compartment door and tighten the screw with a Phillips screwdriver. Do not over-tighten.
Assembly Hole Threaded Bar Plastic Screw Tripod • • • • • Place the projector/telescope upside-down on a flat surface. Position the tripod with the rib side facing down. Insert the tripod into the center slot on the projector/telescope. Align the holes in the projector/telescope with the hole in the tripod. Push the threaded bar through the holes in the projector/telescope and the tripod. • Place the plastic screw on the end of the threaded bar and tighten. Do not over-tighten.
Using the Telescope WARNING Never point the telescope at or near the sun. Viewing the sun can cause instant, permanent eye damage. Cushioned Eyepiece Telescope Focus Knob Angle Adjustment Knob Tripod Helpful Hints: This product has been designed for use with children. We do, however, recommend that you help them set up the product for telescope or projector use and teach them how to use it. Remove ViewMaster® reel from the projector before using the telescope.
Telescope Tips STOP POTS Actual Image Image Viewed Through Telescope • This telescope has a magnification power of 17.5X. This means that objects seen through the telescope look 17.5 times larger than with the eyes alone. • This telescope is a refracting telescope. When you look at an object with this telescope, the object will appear backwards. For example, if you look at a STOP sign, you will see the word backwards (refer to the picture above).
Using the Projector Slot Advance Lever Reel Storage Compartment Projector Focus Knob On/Off Switch Tripod On/Off Switch • • • • • • You can use the projector to send bright, clear images from any View-Master® reel onto walls, ceilings or just about anywhere. Unfold the tripod into the open position. Stand the projector on its legs on a hard, flat surface. Point the projector at the desired viewing area. Tighten the angle adjustment knob. Do not over-tighten.
Advance Lever Projector Focus Knob Advance • To focus the image: Adjust the Lever projector focus knob until the image is clear. Projector Focus Knob • To see the next picture: Press the advance lever. Helpful Hint: Since you cannot rewind to a favorite picture, continue to press the advance lever to find a desired picture. Projector Tips • For the steadiest picture show, place the projector on a hard, flat surface. • Make sure the play area is completely dark for maximum picture clarity.
Storage Reels Reel Storage Compartment • Store ViewMaster® reels in the reel storage compartment. • Loosen the angle adjustment knob. • Fold the tripod legs up. • Tighten the angle adjustment knob to lock tripod legs in place. Do not over-tighten. • Carry this product using the convenient carrying handle.
Light Bulb (Glass Bulb) Replacement IMPORTANT! Should the light bulb become non-functional, you are advised to remove or replace it. This should be carried out away from the child’s play area. Notch 1 Light Bulb Compartment Door Keyhole Tab Screw • Using a Phillips screwdriver, turn the keyhole clockwise. Note: Make sure the tab aligns with the notch. • Loosen the screw on the light bulb compartment door with a Phillips screwdriver. • Lift the light bulb compartment door to open.
3 Keyhole • Close the light bulb compartment door and tighten the screw with a Phillips screwdriver. Do not over-tighten. • Using a Phillips screwdriver, turn the keyhole counterclockwise. • Turn the projector on without a reel in place. • Using a Phillips screwdriver, turn the keyhole clockwise and counter-clockwise to adjust the bulb brightness. Helpful Hint: Point the projector at a white wall or surface to help determine bulb brightness.