Manual
16 9
d. The salt mode can be activated or turned off with the Auto
Ground button. While in the MENU, when the two-digit display
shows “SO”, the salt mode is off. Use this setting for all hunting
conditions except wet sand (beaches) with salt content and NO
black sand (magnetic soil). Press and release the Auto Ground
button to toggle the SALT mode on (display will show “S1”). Press
and release again to toggle it off. For more beach hunting tips,
see the WET SAND HUNTING section.
e. The VOLUME can be adjusted and listened to when the VOLUME
icon is ashing by using the UP and DOWN arrow buttons.
f. The NOTCH Discrimination (“no” on the two digit display in the
MENU) can be adjusted as follows:
1. The UP/DOWN arrow buttons will allow you to choose which
NOTCH category to alter.
2. Once you have chosen which category to change (FOIL,
NICKEL, TABS, or ZINC), pushing and releasing the ALL METAL/DISC
button turns the NOTCH lter ON or OFF.
- If the square next to the chosen category blinks quickly (on
more than off) that target will be accepted.
- If the square next to the chosen category blinks slowly (off
more than on) that target will be rejected.
- When in the SEARCH mode, if the square is ON, the target is
accepted; if the square is OFF, the target is rejected.
Remember, to exit the MENU mode at any time, simply press the
P/P (MEM) button to return to the SEARCH mode
4. The AUTO GROUND button enables you to achieve a precision
ground balance with one touch. Auto Ground Balance is explained
in more detail on page 15. This button also toggles the SALT mode
on or off while in MENU mode.
CONTROL PANEL
Your new Coin Strike provides you with 3 memory locations to
store your favorite control settings. These memory locations will
store the Iron DISC level, THRESHOLD level, SENSITIVITY level, and
NOTCH disc. Please note that the SALT Mode and VOLUME level
will not be stored.
At this point, we would also like to remind you that your Coin Strike
has a last-setting memory feature. This means that the unit will
maintain the control settings when it is turned OFF, saving the same
settings for you when you turn your Coin Strike back ON (except
for the salt mode; this will always default to salt mode off).
By pressing the MENU button to enter the MENU mode and then
pressing it again until the “MEM” icon begins ashing, you will be
ready to store or recall your settings. Memory address “0” always
contains your current control settings, and is not a location to store
settings for later recall.
STORING SETTINGS:
1. Set the controls (DISC, THRESH, SENS, and NOTCH) by using
the MENU button to select the control, and the UP and
DOWN arrow buttons to set to the desired levels.
2. Once the controls are set, press the MENU button until the
“MEM” icon blinks.
3. Use the UP or DOWN arrow buttons to select the MEM 1,
MEM 2, or MEM 3 storage location.
4. Then, press and hold the P/P MEM button for about 3
seconds. When the settings are stored, an audio tone will
sound and the “MEM” icon will blink twice. Release the P/P
MEM button and you are in the search mode and ready to
hunt. In addition, the settings are stored in the MEM location
you chose (1, 2, or 3).
RECALLING SETTINGS:
1. To recall a stored setting, press the MENU button to enter
the MENU mode, and then press it repeatedly until the MEM
icon is selected.
2. Using the UP or DOWN arrow buttons, select the MEM
location you want to recall.
Then, press the P/P MEM button for only 1 second and release it. A
brief audio tone will sound and the detector will enter the search
mode in the settings you recalled.
Selecting the factory preset (FP) memory setting is described on
page 11.
SETTING MEMORY CONTROL
CoinStrikeManual-8730015.indd 9 6/9/06 4:12:34 PM