MPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo and, subject to change without notice. 2810.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. If you need help with product information, assembly, or replacement parts. Please contact customer service. Email us at: Service@paradigmhw.
TABLE OF CONTENTS SERVICE ------------------------------------------------------------------- 2 LABLE PLACEMENT --------------------------------------------------- 3 PRODUCT SAFETY ----------------------------------------------------- 4 ASSEMBLY PREPATION----------------------------------------------- 5 OVERVIEW DRAWING ------------------------------------------------ 6 PART LIST ----------------------------------------------------------------- 7 HARDWARE PACK ------------------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Daily) by below methods: For Best Service Email: Service@paradigmhw.com Website: www.paradigmhw.
LABEL PLACEMENT 3
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your physician to see if this workout equipment is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommended that you have assistance during the assembly of the strength equipment. 1. Tools for assembly: General tools you may need for the assembling this strength equipment: • Metric Allen Key Set • Metric Wrench Set and Adjustable Wrench • Flat Screwdrivers • Phillips Screwdrivers • Rubber Mallet • Silicone Spray Oil 2. Insert bolts into the frame as illustrated in the drawing of each of the steps. 3.
OVERVIEW DRAWING 6
PART LIST Part # Description Q'ty A Base Frame 2 B Upright Frame 4 C Upper Frame 2 D Pull Up Bar 1 H Short Safety Catch 2 I Long Safety Catch 2 K Rear Cross Bar 2 L L-Bracket 8 32 Hexagon Head Bolt M10*73 40 67 Washer D10.5*D30*1.
HARDWARE PACK 8
HARDWARE PACK 9
PRODUCT DRAWING 10
STEP 1 1A. Insert a Foot End Cap (485) into each side of the Base Frame (A). 1B. Insert two Upright Frames (B) into the brackets of the Base Frame (A). Make sure the arrow stickers on the Upright Frames (B) are pointing away from the Base Frame (A). 1C. Attach the Base Frame (A) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until the unit is completely assembled.
STEP 1 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS 12
STEP 2 2A. Slide the two Upright Frames (B) into the brackets at the ends of the Upper Frame (C). 2B. Attach the Upper Frame (C) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until the unit is completely assembled.
STEP 2 13-17mm Wrench 2 PCS B (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS 14
STEP 3 3A. Insert a Foot End Cap (485) into each side of the Base Frame (A). 3B. Insert two Upright Frames (B) into the brackets of the Base Frame (A). Make sure the arrow stickers on the Upright Frames (B) are pointing away from the Base Frame (A). 3C. Attach the Base Frame (A) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until the unit is completely assembled.
STEP 3 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS 16
STEP 4 4A. Slide the two Upright Frames (B) into the brackets at the ends of the Upper Frame (C). 4B. Attach the Upper Frame (C) to the two Upright Frames (B) by using: 4 - (32) Hexagon Head Bolt 8 - (67) Washer 4 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until the unit is completely assembled.
STEP 4 13-17mm Wrench 2 PCS B (32) Hexagon Head Bolt 4PCS (67) Washer (75) Nylon Lock Nut 8PCS 4PCS 18
STEP 5 5A. Mount the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C). 5B. Attach the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C) by using: 6 - (32) Hexagon Head Bolt 12 - (67) Washer 6 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until the unit is completely assembled.
STEP 5 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 6PCS (67) Washer 12PCS 20 (75) Nylon Lock Nut 6PCS
STEP 6 6A. Mount the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C). 6B. Attach the Pull Up Bar (D) and two L-Brackets (L) to the Upper Frame (C) by using: 6 - (32) Hexagon Head Bolt 12 - (67) Washer 6 - (75) Nylon Lock Nut Do not thoroughly tighten the hardware until the unit is completely assembled. Note: Having someone to assist for this step is recommended.
STEP 6 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 6PCS (67) Washer 12PCS 22 (75) Nylon Lock Nut 6PCS
STEP 7 7A. Attach the two Rear Cross Bars (K) and four L-Brackets (L) to the Upright Frames (B) by using: 12 - (32) Hexagon Head Bolt 24 - (67) Washer 12 - (75) Nylon Lock Nut Give the cage a shake so the frame can settle and then thoroughly tighten ALL the hardware.
STEP 7 13-17mm Wrench 2 PCS (32) Hexagon Head Bolt 12PCS (67) Washer 24PCS 24 (75) Nylon Lock Nut 12PCS
STEP 8 A. The two Long Safety Catches (I) can be inserted into any of the holes along the Upright Frame (B). Place them at the same level on the left and right side of the cage and at a comfortable height that will assist you during your workout. B. The two Short Safety Catches (H) can be inserted into any of the holes along the Upright Frame (B). Place them at the same level on the left and right side of the cage and at a comfortable height that will assist you during your workout. C.
STEP 8 Fig.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PARTS REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.
