AB B Hyp per Bench B h Read all instruction i ns carefully ly before using u this product. p R Retain this owner’s manual fo or future re eference. T The speciffications off this prod duct may vary v from this photo o and, subjject to cha ange without notice. 286 60.
STOP ARRÊT ALTO PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. If you need help with product information, assembly, or replacement parts. Please contact customer service. Email us at: Service@paradigmhw.
TABLE OF CONTENTS SERVICE-------------------------------------------------------------------- 2 LABEL PLACEMENT----------------------------------------------------- 3 PRODUCT SAFETY------------------------------------------------------ 4 ASSEMBLY PREPARATION-------------------------------------------- 5 OVERVIEW------------------------------------------------------------------ 6 HARDWARE PACK-------------------------------------------------------- 7 PART LIST-------------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Open Daily) by below methods: For Best Service Email: Service@paradigmhw.com* Website: www.paradigmhw.
3 UNDER PENALTY OF LAW THIS TAG NOT TO BE REMOVED EXCEPT BY THE CONSUMER ALL NEW MATERIALCONSISTING OF POLYURETHANE FOAM PAD_100% REGISTRY NO. VA25302 (CN) manufacturer that the materials in this article are described in accordance with law. NOTICE This article does not meet requirements of California Bureau of Home Furnishings technical bulletin 117. Care should be exercised burning cigaretts. Paradigm Health and Wellness, Inc. 1189 Jellick Ave.
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your personal physician to see if AB Hyper Bench is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommended that you have assistance during the assembly of this IRONMAN strength equipment. 1. Tools for assembly: General tools needed for the assembly of this IRONMAN strength equipment: Metric Allen Key Set Metric Wrench Set and Adjustable Wrench Flat Screwdrivers Phillips Screwdrivers Rubber Mallet Silicone Spray Oil 2. Insert the bolts into the frame as illustrated in the drawing of each of the steps. 3.
OVERVIEW DRAWING 6
HARDWARE PACK 7
PART LIST Part# Description Qty. Part# Description Qty. A Backrest Support Tube 1 75 Nylon Nut M10x1.5x10T 4 B Rear Support Tube 1 100 Pin D9.4x70 2 C Handle Grip Tube 1 102 Ball Knob D50xM16x22xD8 1 D Front Support Tube 1 120 Round Cap D25.4xD65x31.5 2 E Swing Tube 1 123 Round Cap D60xD67x43L 2 F Backrest Pad 900x300x60T 1 124 Round Cap D31.8x19L 2 G Support Pad 200x200x50T 2 127 ROUND CAP D60xD70x101L 2 3 Hex Bolt M8x1.
9
STEP 1 1A. Slide the Rear Support Tube (B) through the bracket of the Backrest Support Tube (A). Fasten the Rear Support Tube (B) to the Backrest Support Tube (A) using: 1 - (6) Hex Bolt M10x1.5x80L 2 - (51) Flat Washer D20xD11x2T 1 - (75) Nylon Nut M10x1.5x10T 1B. Align the adjustment holes on the Backrest Support Tube (A) with Rear Support Tube (B) and lock the two parts into place using: 1 - (100) Pin D9.4x70 Thoroughly tighten the hardware once complete Appearance upon completion of step 1.
STEP 1 17 13 Wrench 2 PCS NO. 100 PIN D9.4x70 1PC NO.6 Hex Bolt M10x1.5x80L 1PC NO. 75 Nylon Nut M10x1.5x10T 1PC 11 NO.
STEP 2 2A. Insert the Rear Support Tube (B) into the bracket of Front Support Tube (D) by aligning the two holes and fasten together using: 2 - (5) Hex Bolt M10x1.5x75L 4 - (51) Flat Washer D20xD11x2T 2 - (75) Nylon Nut M10x1.5x10T Thoroughly tighten the hardware once complete Appearance upon completion of step 2.
STEP 2 17 13 Wrench 2 PCS NO. 5 Hex Bolt M10x1.5x75L 2PCS NO.51 Flat Washer D20xD11x2T 4PCS 13 NO. 75 Nylon Nut M10x1.
STEP 3 3A. Fasten the Swing Tube (E) to hole on the underside of Front Support Tube (D) using: 1 - (6) Hex Bolt M10x1.5x80L 2 - (51) Flat Washer D20xD11x2T 1 - (75) Nylon Nut M10x1.5x10T 3B. Align the Swing Tube (E) to the adjustment holes on the front of Front Support Tube (D) and lock the two parts in place Using: 1 - (100) Pin D9.4x70 Thoroughly tighten the hardware once complete Appearance upon completion of step 3.
STEP 3 17 13 Wrench 2 PCS NO. 100 PIN D9.4x70 1PC NO. 75 Nylon Nut M10x1.5x10T 1PC NO. 6 Hex Bolt M10x1.5x80L 1PC 15 NO.
STEP 4 4A. Insert Handle Grip Tube (C) into the Square shaft of the Front Support Tube (D). Lock the Handle Grip Tube into place using the Ball Knob (102) located on the underside of the Front Support Tube (D). 4B. Mount the Foam Roller (222) with the Foam Rollers Sleeves (223) onto the posts of the Swing Bar (E).
STEP 4 4 NO.1 20 Round d Cap D2 25.4xD65x x31.
STEP 5 5A. Attach both Support Pads (G) to Handle Grip Tube (C) using: 4 - (3) Hex Bolt M8x1.25x25L 4 - (50) Flat Washer D18xD8.5x1.2T 4 - (54) Spring Washer D15.4xD8.2x2T Note: loosely install all the hardware by hand prior to tightening with tools. This will make aligning the holes easier Thoroughly tighten the hardware once complete Appearance upon completion of step 5.
STEP 5 17 13 Wrench 1PC NO.3 Hex Bolt M8*1.25*25L 4PCS NO.54 Spring Washer D15.4*D8.2*2T 4PCS 19 NO. 50 Flat Washer D18*D8.5*1.
STEP 6 6A. Attach both Backrest Pad (F) to Backrest Support Tube (A) using: 4 - (3) Hex Bolt M8x1.25x25L 4 - (50) Flat Washer D18xD8.5x1.2T 4 - (54) Spring Washer D15.4xD8.2x2T Note: loosely install all the hardware by hand prior to tightening with tools.
STEP 6 17 13 Wrench 1PC NO.3 Hex Bolt M8*1.25*25L 4PCS NO.54 Spring Washer D15.4*D8.2*2T 4PCS 21 NO. 50 Flat Washer D18*D8.5*1.
AD DJUSTMENTS age AA-1)) 1. Swing Tube Adjusttment (Ima Raise R or lo ower the Swing S Tube e (E) into tthe desired position, align the adjustment holes, and a secured s it in place with w the Pin n (100) befo fore using the t AB Hyper Benchh. 2.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness guarantees to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PART REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECEIPT OF PURCHASE TO Service@paradigmhw.