Leg Development Attachment MPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo and, subject to change without notice. 2851.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. If you need help with product information, assembly, or replacement parts. Please contact customer service. Email us at: Service@paradigmhw.
TABLE OF CONTENT SERVICE-------------------------------------------------------------------- 2 LABEL PLACEMENT----------------------------------------------------- 3 PRODUCT SAFETY------------------------------------------------------ 4 ASSEMBLY PREPARATION-------------------------------------------- 5 OVERVIEW------------------------------------------------------------------ 6 HARDWARE PACK-------------------------------------------------------- 7 PART LIST-------------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Open Daily) by below methods: For Best Service Email: Service@paradigmhw.com Website: www.paradigmhw.
LABEL PLACEMENT 3
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your personal physician to see if this Leg Development Attachment is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommend that you have assistance during the assembly of this strength equipment. 1. Tools for assembly: General tools you may need for the assembling this strength equipment: • Metric Allen Key Set • Metric Wrench Set and Adjustable Wrench • Flat Screwdrivers • Phillips Screwdrivers • Rubber Mallet • Silicone Spray Oil 2. Insert the bolts into the frame as illustrated in the drawing of each of the steps. 3.
OVERVIEW DRAWING 6
HARDWARE PACK 7
PART LIST Part# Description Q’ty. Part# Description Q’ty. A Main Frame Post 1 101 Push Pin D8x55L 1 B Leg Development Tube 1 120 Round Cap D25.4xD65x31.5 5 C Handlebar 1 125 Round Cap D50.8x15 2 D Preacher Curl Post 1 126 Round Cap D1"x17 4 E Preacher Curl Pad 1 153 Square Cap 50x50x20L 1 F Foam Roller Tube D25.4x2.0Tx450L 2 155 Square Cap 30x70x17L 2 G Rotating Axle D12x58.5L 1 185 Buffer D35xD25.5x24 1 2 Hex Bolt M8x1.
9
STEP 1 1A. Attach Leg Development Tube (B) onto the Main Frame Post (A) by using: 2 - (2) Hex Bolt M8x1.25x20L 2 - (54) Spring Washer D15.4xD8.2x2T 2 - (53) Flat Washer D25xD8.5x2T 1 - (G) Rotating Axle D12x58.
STEP 2 13,15 mm Wrench 2PCS NO.2 Hex Bolt M8x1.25x20L 2PCS NO.53 Flat Washer D25xD8.5x2T 2PCS NO.54 Spring Washer D15.4xD8.2x2T 2PCS 12 NO.G Rotating Axle D12x58.
STEP 2 2A. Attach 2 Foam Rollers and Foam Roller Sleeve (222, 223) onto the circular tubes on Main Frame Post (A) and secure them into place with 2 Round Cap (120) using: 2 - (222) Foam Roller D23xD100x200L 2 - (223) Foam Roller Sleeve 2 - (120) Round Cap D25.4xD65x31.5 2B. Insert a Foam Roller Tube (F) into the hole at the bottom of Leg Development Tube (B). Attach a Foam Roller and Foam Roller Sleeve (222, 223) to each side of the Foam Roller Tube (F).
STEP 2 NO.120 Round Cap D25.4xD65x31.5 5 PCS NO.
STEP 3 3A. Slide Preacher Curl Post (D) into the Square tube of the Main Frame Post (A). Secure Preacher Curl Post (D) to Main Frame Post (A) with Push Pin (101). Using: 1 - (101) Push Pin D8x55L 3B. Attach Handlebar (C) to Leg Development Tube (B) with Push Pin (100). Using: 1 - (100) Push Pin D9.
STEP 3 NO.100 Push Pin D9.4x70 1PC D.
STEP 4 4A. Attach the Preacher Curl Pad (E) to the Preacher Curl Post (D) as shown in diagrams AA-1 and AA-2 using: 4 - (3) Hex Bolt M8x1.25x25L 4 - (50) Flat Washer D18xD8.5x1.2T 4 - (54) Spring Washer D15.4xD8.2x2T Note: Loosely insert all the hardware by hand first. This will allow for all the holes to be aligned prior to fastening. 4B. When all the Hex Bolt (2) have been inserted, proceed to tightening the bolts to completely secure the Preacher Curl Pad (E) to the Preacher Curl Post (D).
STEP 4 13,15 mm Wrench 1PC NO.3 Hex Bolt M8x1.25x25L 4PCS NO.54 Spring Washer D15.4xD8.2x2T 4PCS 17 NO.50 Flat Washer D18xD8.5x1.
Clip Installation Install the Standard Clip (295), please follow the steps below: A. To secure your weight plates, pinch the rubber grips of Standard Clip (295). B. Slide the Standard Clip (295) on to the post of the Leg Development Tube (B). C. Standard Clip (295) should be pushed all the way down until it makes contact with the weight plates, securing the weight plates to the backside of the weight post of the Leg Development Tube (B).
ADJUSTMENTS 1. Height Adjustment: The height of the Preacher Pad (E) can be adjusted up and down by removing the Push Pin (101) from Main Frame Post (A), and aligning the adjustment holes of Main Frame Post (A) and Preacher Curl Post (D). When the desired height is selected completely reinsert the Push Pin (101) into Main Frame Post (A) and Preacher Curl Post (D). 2. Arm Length Adjustment: Handlebar (C) has two positions setting for arm length.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness guarantees to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PART REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.
