Quick Installation Guide

ManualsBrandsFlir ManualsSecurity Cameras320 X 256 Network Outdoor Thermal Imaging Camera with 18mm Lens

Table Of Contents

Quick Install Guide

427-0200-01-10 Rev 120

October 2021

This document does not contain any export-controlled information.

Saros™ PTZ

DM-Series Camera

Quick Install Guide

1 Check Contents

Make sure all of the items above are included in the camera kit.

2 Prepare to Install the Camera

2.1 Install FLIR Discovery Network Assistant

Download the FLIR Discovery Network Assistant (DNA) tool to a computer on the

same VLAN to which you will connect the camera, and then unzip the file. The

DNA tool does not require a license to use and is a free download from

www.teledyneflir.com > Products > Security > Thermal Security Cameras > Saros

DM-Series.

2.2 Perform a Bench Test (Optional)

You can test the camera or configure it for networking before mounting it. Follow

the instructions in 3.4 Connect the Camera and 4.1 Configure for Networking, and

then continue with 2.3 Select a Location.

Summary of content (7 pages)

PAGE 1
Saros™ PTZ DM-Series Camera Quick Install Guide 1 Check Contents Make sure all of the items above are included in the camera kit. 2 Prepare to Install the Camera 2.1 Install FLIR Discovery Network Assistant Download the FLIR Discovery Network Assistant (DNA) tool to a computer on the same VLAN to which you will connect the camera, and then unzip the file. The DNA tool does not require a license to use and is a free download from www.teledyneflir.
PAGE 2
.3 Select a Location Select a suitable location to mount the camera. For advice on positioning and orienting the camera, see the camera's installation and user guide. Verify that the operating temperature range is between -40° ~ 55° C (-40° ~ 131° F), 10-90% relative humidity (non-condensing). For the list of mounting accessories available for the camera, see the FLIR Security Cameras - Accessory Guide. 3 Install the Camera 3.
PAGE 3
Connector Connection 1 UPOE Attach a Cat 5e or Cat 6 cable from the network switch to the RJ45 connector for a 10/100/1000 Mbps Ethernet and PoE connection. If using PoE, use a FLIR CP-POE4P-60W-xx injector or a switch that supports Universal PoE 60W 4 pair forced mode. For more information about compatible injectors and recommended switches, contact Teledyne FLIR support. Verify that the UPOE connector LEDs are steady green and flashing yellow.
PAGE 4
DNA tool Discover camera IP address • Configure IP address, mask, and gateway • Camera's web page Configure DNS settings, MTU, and Ethernet speed • • Change user credentials • Configure more than one camera at the same time • • For more information about using a VMS to configure one or more cameras at the same time, see the VMS documentation. 4.1 Configure for Networking By default, DHCP is enabled on the camera and a DHCP server on the network assigns the camera an IP address.
PAGE 5
Click Login, wait for Ok status to appear, and then click Close. In the DNA Discover List, verify that the camera's status is Authenticated. d. Change the camera’s IP address. Right-click the camera and select IP Setup. In the DNA - IP Setup window, clear Use DHCP and specify the camera's IP address. You can also specify the Mask (default: 255.255.255.0) and Gateway. Then, click Update, wait for Ok status to appear, and then click Close.
PAGE 6
d. Click System Settings. Make sure the Network page appears. e. You can select Static and manually specify the camera's Hostname, IP address, Netmask, and Gateway. You can also specify the DNS Mode, Name Servers, MTU (maximum transmission unit), and Ethernet Speed. f. Click Save. If you have made any changes on the Network page, the camera reboots. Note For more information about configuring the camera for networking, see the camera’s installation and user guide.
PAGE 7
4.2 Attach the Camera to a Supported VMS After you have mounted the camera and discovered or defined its IP address, use VMS Discovery/Attach procedures to attach the camera to a supported VMS. 5 Camera Dimensions Following are the Saros PTZ DM-Series camera’s dimensions. Front View Side View 6 Register the Product Register the product at https://customer.flir.com. For warranty information, see https://www.flir.com/supportcenter/warranty/security/flir-security-product-warranties/.