Quick Connect Guide

ManualsBrandsFlir ManualsSecurity Cameras640 X 480 Outdoor Network Thermal Camera, 7.5mm Lens, 30HZ, NTSC

427-0089-00-28 Rev 120 July 2016

FC-Series ID Camera

Quick Connect Guide

Caution!

Except as described in this guide, do not disassemble the FC-Series ID camera.

Damage to the camera can occur as the result of careless handling or

electrostatic discharge (ESD).

Before installing the FC-Series ID camera you should read and understand the

following documents which provide details regarding mechanical dimensions

and installation safety.

• FLIR FC-Series ID Installation Manual (427-0089-00-12)

• FLIR FC-Series ID Interconnect Document (427-00XX-YY-41)

Power: Power Over Ethernet Plus (PoE+) or 11 - 32 Vdc or 18 - 32 Vac

Power terminal blocks: wire size from 16 AWG to 20 AWG

Analog Video Cable: BNC-terminated RG-59/U solid-center coax cable

Ethernet Cable: Cat5e or Cat6

Accessory I/O plugs: conductor size 22 - 24 AWG, stranded, 1.6 mm max

diameter including insulation for IDC fast connect. Otherwise, 20 - 24 AWG for

push-in spring connect, strip ends 6 mm. GPIO accessory cable.

FLIR Systems, Inc.

6769 Hollister Avenue

Goleta, CA 93117

USA

Support: http://www.flir.com/security/display/?id=71083

Corporate Headquarters

27700 SW Parkway Ave.

Wilsonville, OR 97070

USA

Items Included in Kit

3 mm hex

Slotted

screwdriver

key

427-0089-00-28 v120 FC-Series Quick Connect.fm Page 1 Thursday, July 7, 2016 7:38 AM

Summary of content (4 pages)

PAGE 1
427-0089-00-28 v120 FC-Series Quick Connect.fm Page 1 Thursday, July 7, 2016 7:38 AM FC-Series ID Camera Quick Connect Guide Slotted screwdriver 3 mm hex key Items Included in Kit Caution! Except as described in this guide, do not disassemble the FC-Series ID camera. Damage to the camera can occur as the result of careless handling or electrostatic discharge (ESD).
PAGE 2
427-0089-00-28 v120 FC-Series Quick Connect.fm Page 2 Thursday, July 7, 2016 7:38 AM Step 1 Remove cover: Using 3 mm hex key, loosen four captive screws. Access screws through slots in sunshield. Removing the sunshield is not necessary. Step 2 Install cables through sealing gland: Gland nut Video coax Accessory Fill any unused hole with orange plug. Re-tighten gland nut after installation is completed.
PAGE 3
427-0089-00-28 v120 FC-Series Quick Connect.fm Page 3 Thursday, July 7, 2016 7:38 AM Step 4 Connect a ground wire between the ground stud on the back of the camera and the nearest earth-grounding point. Step 5 Tighten Cable seal gland nut to ensure a watertight seal. Step 6 Replace cover: Alternately tighten the four captive screws in the cover; torque to 1.8 N-m (16.0 in-lbs). Step 7 Discover camera: Power the camera.
PAGE 4
27-0089-00-28 v120 FC-Series Quick Connect.fm Page 4 Thursday, July 7, 2016 7:38 AM d. To create an Area, Tripwire, or Masking Area, click the select from the Type drop-down list. d. e. Define the Area, Tripwire, or Masking Area by clicking vertex locations on the screen. f. icon and f. g. Click Finish. g. In the Regions pane select the tripwire. h. h. In the Properties pane, set the direction of the detection from the Direction drop-down list. i. i.