Product Manual

ManualsBrandsFlotec ManualsWater Pump AccessoriesVertical Pre-Charged Water System Tank — 35-Gallon Capacity, Drawdown Equivalent to an 82 Gallon Capacity Tank

OWNER’S MANUAL

Pre-Charged Pressure and

Horizontal Tanks and Fittings

NOTICE D’UTILISATION

Réservoirs horizontaux et à pression

préchargée, avec connexions

MANUAL DEL USUARIO

Tanques de presion precargada,

tanques horizontales y accesorios

P.O. Box 342, Delavan, WI 53115

Phone: 1-800-365-6832

Fax: 1-800-526-3757

E-Mail: info@flotecwater.com

Web Site: http://www.flotecwater.com

MODELS

FP7100

FP7100H

FP7110

FP7110T

FP7110TH

FP7120

FP7125

FP7130

FP7135

Installation/Operation/Parts

For further operating,

installation, or maintenance

assistance:

Call 1-800-365-6832

English..................... Pages 2-7

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

1 (800) 365-6832

Français ................ Pages 8-13

Instalación/Operación/Piezas

Para mayor información sobre

el funcionamiento, instalación

o mantenimiento de la bomba:

Llame al 1-800-365-6832

Español..............Paginas 14-19

Summary of content (7 pages)

PAGE 1
OWNER’S MANUAL ® P.O. Box 342, Delavan, WI 53115 Phone: 1-800-365-6832 Fax: 1-800-526-3757 E-Mail: info@flotecwater.com Web Site: http://www.flotecwater.
PAGE 2
Safety 2 READ AND FOLLOW SAFETY INSTRUCTIONS! This is the safety alert symbol. When you see this symbol on your pump or in this manual, look for one of the following signal words and be alert to the potential for personal injury. warns about hazards that will cause serious personal injury, death or major property damage if ignored. warns about hazards that can cause serious personal injury, death or major property damage if ignored.
PAGE 3
General Information 3 GENERAL INFORMATION OPERATING CYCLE (FIGURE 2) Tanks listed below are pre-charged, or filled with air at the factory, to 40 pounds per square inch (PSI) (276kPa). When installing tank, set tank pressure according to Chart 1. To do this, bleed air from or add air to tank through valve on top of tank. NOTICE: Always set or check tank pre-charge with NO WATER in tank or water pressure in system.
PAGE 4
Installation 4 For jet pump installation, remove AVC tube from port in pump body or jet body and plug port (see Figure 3). New pumps come with plug installed. 148 0893 Figure 3: Plug AVC Port when installing pre-charged tank on existing pumps. New pumps come with plug Installed. NOTICE: When working on submersible pumps in wells be sure safety rope is solidly connected to pump and to secure anchor at the well head at all times.
PAGE 5
Installation 5 TESTING FOR BLADDER LEAKAGE Step 1. Disconnect power to pump. Step 2. Drain water from tank bladder by opening faucet closest to tank. Step 3. Remove valve cap and release all pressure by depressing valve core. When air stops coming from valve, remove valve core to release remaining pressure. Step 4. Disconnect piping from elbow on tank cover flange. Step 5. Carefully turn tank upside down or lay on its side.
PAGE 6
Repair Parts 6 Model FP7100-08 4 1 2 2880 0797 RTL 3 Model FP7100H-08 4 1 2 3 REPAIR PARTS LIST Key No. 1 2 3† 4 Part Description Bladder - Vinyl Cover Flange Flanged Nut - 5/16 - 18 Hex. Air Valve with Cap No. Used 1 1 6 1 FP7100H-08 U20-7 U31-442P U36-202BT U212-160 FP7100-08 U20-7 U31-442P U36-202BT U212-160 † Standard hardware items, may be purchased locally.
PAGE 7
Repair Parts 7 Models FP7110-08 FP7110T-08 FP7110TH-08 FP7120-08 FP7125-08 FP7130-08 FP7135 4 1 2 2399 0496SRS 3 REPAIR PARTS LIST Key No. Part Description No. Used FP7110-08 FP7110T-08 FP7110TH-08 1 2 3 4 Bladder - Vinyl Cover Flange and Elbow Flanged Nut - 5/16 - 18 Hex Air Valve with Cap 1 1 6 1 U20-8 U31-446P U36-202BT U212-160 U20-13 U31-446P U36-202BT U212-160 U20-13 U31-446P U36-202BT U212-160 Key No. Part Description No.