Instructions
Table Of Contents
- Getting Started Guide
- Guide d’introduction
- Erste Schritte
- Guida introduttiva
- Guia de introdução
- Guía de funcionamiento básico
- Guide de démarrage
- Symboles
- WConsignes de sécurité
- Touches
- Fonctionnalités d’affichage
- Changement des unités de longueur
- Arrêt automatique
- Tests de câble
- Utilisation du générateur de tonalités
- Détection de Power Over Ethernet (PoE)
- Changement des piles
- En savoir plus
- Coordonnées de Fluke Networks
- Caractéristiques générales
- EXCLUSION DE GARANTIE ET RESPONSABILITE LIMITEE
- Erste Schritte
- Symbole
- WSicherheitshinweise
- Tasten
- Display-Funktionen
- Ändern der Längeneinheit
- Automatische Abschaltung
- Testen von Kabeln
- Verwenden des Toners
- PoE-Erkennung (Power over Ethernet)
- Ersetzen der Batterien
- Erfahren Sie mehr
- Kontaktinformationen von Fluke Networks
- Allgemeine Spezifikationen
- BESCHRÄNKTE GARANTIE UND HAFTUNGSBEGRENZUNG
- Guida introduttiva
- Simboli
- WInformazioni sulla sicurezza
- Tasti
- Funzioni del display
- Modifica dell'unità di misura della lunghezza
- Spegnimento automatico
- Test dei cavi
- Utilizzo del toner
- Rilevamento di Power Over Ethernet
- Sostituzione delle batterie
- Ulteriori informazioni
- Contattare Fluke Networks
- Specifiche generali
- GARANZIA LIMITATA E LIMITAZIONE DI RESPONSABILITÀ
- Guia de introdução
- Símbolos
- WInformações de segurança
- Teclas
- Recursos de exibição
- Como mudar a unidade de comprimento
- Desligamento automático
- Testes de cabos
- Como usar o gerador de tom
- Detecção de alimentação por Ethernet (PoE – Power Over Ethernet)
- Como trocar as pilhas
- Saiba mais
- Como contatar a Fluke Networks
- Especificações gerais
- GARANTIA LIMITADA E LIMITAÇÃO DE RESPONSABILIDADE
- Руководство по началу работы
- Обозначения
- WИнформация о технике безопасности
- Кнопки
- Элементы дисплея
- Переключение между единицами измерения длины
- Автоматическое выключение тестера
- Тестирование кабеля
- Использование генератора тональных сигналов
- Обнаружение питания по Ethernet
- Замена батарей
- Подробная информация
- Контактная информация Fluke Networks
- Общие спецификации
- ОГРАНИЧЕННАЯ ГАРАНТИЯ И ОГРАНИЧЕНИЯ ОТВЕТСТВЕННОСТИ
- Guía de funcionamiento básico
- Símbolos
- WInformación de seguridad
- Teclas
- Funciones de visualización
- Cambio de las unidades de longitud
- Apagado automático
- Comprobación del cableado
- Uso del emisor de tonos
- Detección de alimentación por Ethernet
- Reemplazo de las baterías
- Aprender más
- Comuníquese con Fluke Networks
- Especificaciones generales
- GARANTÍA LIMITADA Y LÍMITES DE RESPONSABILIDAD
- スタート・ガイド
- 사용 시작 설명서
- 入门指南
8
Changing the Length Units
MicroScanner
2
: Indicates an ID locator is
connected to the far end of the cable.
Ethernet port indicator. The speeds of the
port show under the indicator.
Wiremap diagram. The rightmost segments
indicate the shield.
The Windicates a fault or high voltage on
the cable. SPLIT appears when the fault is a
split pair.
Changing the Length Units
1
Hold down and or and while
turning on the tester.
2
Press or to switch between meters
and feet.
Auto Shutoff
The tester turns off after 10 minutes if no keys
are pressed and nothing changes at the tester’s
connectors.
Testing Cabling
1
Press to turn on the tester.
2
MicroScanner
2
: Press to switch between
twisted pair (
) and coaxial () modes.
3
Connect as shown in the following figures.
If the PoE indicator appears, see page 11.