Instructions
Table Of Contents
- Getting Started Guide
- Guide d’introduction
- Erste Schritte
- Guida introduttiva
- Guia de introdução
- Guía de funcionamiento básico
- Guide de démarrage
- Symboles
- WConsignes de sécurité
- Touches
- Fonctionnalités d’affichage
- Changement des unités de longueur
- Arrêt automatique
- Tests de câble
- Utilisation du générateur de tonalités
- Détection de Power Over Ethernet (PoE)
- Changement des piles
- En savoir plus
- Coordonnées de Fluke Networks
- Caractéristiques générales
- EXCLUSION DE GARANTIE ET RESPONSABILITE LIMITEE
- Erste Schritte
- Symbole
- WSicherheitshinweise
- Tasten
- Display-Funktionen
- Ändern der Längeneinheit
- Automatische Abschaltung
- Testen von Kabeln
- Verwenden des Toners
- PoE-Erkennung (Power over Ethernet)
- Ersetzen der Batterien
- Erfahren Sie mehr
- Kontaktinformationen von Fluke Networks
- Allgemeine Spezifikationen
- BESCHRÄNKTE GARANTIE UND HAFTUNGSBEGRENZUNG
- Guida introduttiva
- Simboli
- WInformazioni sulla sicurezza
- Tasti
- Funzioni del display
- Modifica dell'unità di misura della lunghezza
- Spegnimento automatico
- Test dei cavi
- Utilizzo del toner
- Rilevamento di Power Over Ethernet
- Sostituzione delle batterie
- Ulteriori informazioni
- Contattare Fluke Networks
- Specifiche generali
- GARANZIA LIMITATA E LIMITAZIONE DI RESPONSABILITÀ
- Guia de introdução
- Símbolos
- WInformações de segurança
- Teclas
- Recursos de exibição
- Como mudar a unidade de comprimento
- Desligamento automático
- Testes de cabos
- Como usar o gerador de tom
- Detecção de alimentação por Ethernet (PoE – Power Over Ethernet)
- Como trocar as pilhas
- Saiba mais
- Como contatar a Fluke Networks
- Especificações gerais
- GARANTIA LIMITADA E LIMITAÇÃO DE RESPONSABILIDADE
- Руководство по началу работы
- Обозначения
- WИнформация о технике безопасности
- Кнопки
- Элементы дисплея
- Переключение между единицами измерения длины
- Автоматическое выключение тестера
- Тестирование кабеля
- Использование генератора тональных сигналов
- Обнаружение питания по Ethernet
- Замена батарей
- Подробная информация
- Контактная информация Fluke Networks
- Общие спецификации
- ОГРАНИЧЕННАЯ ГАРАНТИЯ И ОГРАНИЧЕНИЯ ОТВЕТСТВЕННОСТИ
- Guía de funcionamiento básico
- Símbolos
- WInformación de seguridad
- Teclas
- Funciones de visualización
- Cambio de las unidades de longitud
- Apagado automático
- Comprobación del cableado
- Uso del emisor de tonos
- Detección de alimentación por Ethernet
- Reemplazo de las baterías
- Aprender más
- Comuníquese con Fluke Networks
- Especificaciones generales
- GARANTÍA LIMITADA Y LÍMITES DE RESPONSABILIDAD
- スタート・ガイド
- 사용 시작 설명서
- 入门指南
12
Replacing the Batteries
To select PoE mode, press or until PoE
appears on the display. In PoE mode, the tester
solicits PoE power on pairs 1,2-3,6 and 4,5-7,8.
The tester may activate a PoE source and will
not be damaged by PoE power.
If PoE power is detected,
appears above
the powered pairs. The
may blink as the
PoE source turns the power on and off.
In twisted pair test mode, a flashing PoE mode
indicator means that PoE power may be
available. To verify the presence of a PoE
source, switch the tester to PoE mode.
Replacing the Batteries
The batteries last for about 20 hours of typical
use.
EGS28.EPS