Instructions
Table Of Contents
- Getting Started Guide
- Guide d’introduction
- Erste Schritte
- Guida introduttiva
- Guia de introdução
- Guía de funcionamiento básico
- Guide de démarrage
- Symboles
- WConsignes de sécurité
- Touches
- Fonctionnalités d’affichage
- Changement des unités de longueur
- Arrêt automatique
- Tests de câble
- Utilisation du générateur de tonalités
- Détection de Power Over Ethernet (PoE)
- Changement des piles
- En savoir plus
- Coordonnées de Fluke Networks
- Caractéristiques générales
- EXCLUSION DE GARANTIE ET RESPONSABILITE LIMITEE
- Erste Schritte
- Symbole
- WSicherheitshinweise
- Tasten
- Display-Funktionen
- Ändern der Längeneinheit
- Automatische Abschaltung
- Testen von Kabeln
- Verwenden des Toners
- PoE-Erkennung (Power over Ethernet)
- Ersetzen der Batterien
- Erfahren Sie mehr
- Kontaktinformationen von Fluke Networks
- Allgemeine Spezifikationen
- BESCHRÄNKTE GARANTIE UND HAFTUNGSBEGRENZUNG
- Guida introduttiva
- Simboli
- WInformazioni sulla sicurezza
- Tasti
- Funzioni del display
- Modifica dell'unità di misura della lunghezza
- Spegnimento automatico
- Test dei cavi
- Utilizzo del toner
- Rilevamento di Power Over Ethernet
- Sostituzione delle batterie
- Ulteriori informazioni
- Contattare Fluke Networks
- Specifiche generali
- GARANZIA LIMITATA E LIMITAZIONE DI RESPONSABILITÀ
- Guia de introdução
- Símbolos
- WInformações de segurança
- Teclas
- Recursos de exibição
- Como mudar a unidade de comprimento
- Desligamento automático
- Testes de cabos
- Como usar o gerador de tom
- Detecção de alimentação por Ethernet (PoE – Power Over Ethernet)
- Como trocar as pilhas
- Saiba mais
- Como contatar a Fluke Networks
- Especificações gerais
- GARANTIA LIMITADA E LIMITAÇÃO DE RESPONSABILIDADE
- Руководство по началу работы
- Обозначения
- WИнформация о технике безопасности
- Кнопки
- Элементы дисплея
- Переключение между единицами измерения длины
- Автоматическое выключение тестера
- Тестирование кабеля
- Использование генератора тональных сигналов
- Обнаружение питания по Ethernet
- Замена батарей
- Подробная информация
- Контактная информация Fluke Networks
- Общие спецификации
- ОГРАНИЧЕННАЯ ГАРАНТИЯ И ОГРАНИЧЕНИЯ ОТВЕТСТВЕННОСТИ
- Guía de funcionamiento básico
- Símbolos
- WInformación de seguridad
- Teclas
- Funciones de visualización
- Cambio de las unidades de longitud
- Apagado automático
- Comprobación del cableado
- Uso del emisor de tonos
- Detección de alimentación por Ethernet
- Reemplazo de las baterías
- Aprender más
- Comuníquese con Fluke Networks
- Especificaciones generales
- GARANTÍA LIMITADA Y LÍMITES DE RESPONSABILIDAD
- スタート・ガイド
- 사용 시작 설명서
- 入门指南
3
WSafety Information
Carefully read all instructions.
Do not open the case. You cannot repair or
replace parts in the case.
Do not modify the Product.
Use only replacement parts that are
approved by Fluke Networks.
Do not touch voltages > 30 V AC rms, 42 V
AC peak, or 60 V DC.
The tester is not intended to be connected
to active telephone inputs, systems, or
equipment, including ISDN devices.
Exposure to the voltages applied by these
interfaces may damage the tester and create
a potential shock hazard. The tester shows a
warning symbol (
W) and other indicators
when it detects high voltage. See the Users
Manual for examples of these displays.
Disconnect the tester if it detects high voltage.
Do not use the Product around explosive
gas, vapor, or in damp or wet environments.
Use this Product indoors only.
Do not connect the Product to voltages that
are higher than the maximum voltage rating
for the Product.
For Products that have multiple connectors
for different types of tests on copper
cabling, disconnect unused test leads from
the connectors before you do a test.
Use the Product only as specified, or the
protection supplied by the Product can be
compromised.