Instructions
Table Of Contents
- Getting Started Guide
- Guide d’introduction
- Erste Schritte
- Guida introduttiva
- Guia de introdução
- Guía de funcionamiento básico
- Guide de démarrage
- Symboles
- WConsignes de sécurité
- Touches
- Fonctionnalités d’affichage
- Changement des unités de longueur
- Arrêt automatique
- Tests de câble
- Utilisation du générateur de tonalités
- Détection de Power Over Ethernet (PoE)
- Changement des piles
- En savoir plus
- Coordonnées de Fluke Networks
- Caractéristiques générales
- EXCLUSION DE GARANTIE ET RESPONSABILITE LIMITEE
- Erste Schritte
- Symbole
- WSicherheitshinweise
- Tasten
- Display-Funktionen
- Ändern der Längeneinheit
- Automatische Abschaltung
- Testen von Kabeln
- Verwenden des Toners
- PoE-Erkennung (Power over Ethernet)
- Ersetzen der Batterien
- Erfahren Sie mehr
- Kontaktinformationen von Fluke Networks
- Allgemeine Spezifikationen
- BESCHRÄNKTE GARANTIE UND HAFTUNGSBEGRENZUNG
- Guida introduttiva
- Simboli
- WInformazioni sulla sicurezza
- Tasti
- Funzioni del display
- Modifica dell'unità di misura della lunghezza
- Spegnimento automatico
- Test dei cavi
- Utilizzo del toner
- Rilevamento di Power Over Ethernet
- Sostituzione delle batterie
- Ulteriori informazioni
- Contattare Fluke Networks
- Specifiche generali
- GARANZIA LIMITATA E LIMITAZIONE DI RESPONSABILITÀ
- Guia de introdução
- Símbolos
- WInformações de segurança
- Teclas
- Recursos de exibição
- Como mudar a unidade de comprimento
- Desligamento automático
- Testes de cabos
- Como usar o gerador de tom
- Detecção de alimentação por Ethernet (PoE – Power Over Ethernet)
- Como trocar as pilhas
- Saiba mais
- Como contatar a Fluke Networks
- Especificações gerais
- GARANTIA LIMITADA E LIMITAÇÃO DE RESPONSABILIDADE
- Руководство по началу работы
- Обозначения
- WИнформация о технике безопасности
- Кнопки
- Элементы дисплея
- Переключение между единицами измерения длины
- Автоматическое выключение тестера
- Тестирование кабеля
- Использование генератора тональных сигналов
- Обнаружение питания по Ethernet
- Замена батарей
- Подробная информация
- Контактная информация Fluke Networks
- Общие спецификации
- ОГРАНИЧЕННАЯ ГАРАНТИЯ И ОГРАНИЧЕНИЯ ОТВЕТСТВЕННОСТИ
- Guía de funcionamiento básico
- Símbolos
- WInformación de seguridad
- Teclas
- Funciones de visualización
- Cambio de las unidades de longitud
- Apagado automático
- Comprobación del cableado
- Uso del emisor de tonos
- Detección de alimentación por Ethernet
- Reemplazo de las baterías
- Aprender más
- Comuníquese con Fluke Networks
- Especificaciones generales
- GARANTÍA LIMITADA Y LÍMITES DE RESPONSABILIDAD
- スタート・ガイド
- 사용 시작 설명서
- 入门指南
4
WSafety Information
Do not use and disable the Product if it is
damaged.
Do not use the Product if it operates
incorrectly.
Batteries contain hazardous chemicals that
can cause burns or explode. If exposure to
chemicals occurs, clean with water and get
medical aid.
Remove the batteries if the Product is not
used for an extended period of time, or if
stored in temperatures above 50 °C. If the
batteries are not removed, battery leakage
can damage the Product.
The battery door must be closed and locked
before you operate the Product.
Repair the Product before use if the battery
leaks.
Replace the batteries when the low battery
indicator shows to prevent incorrect
measurements.
Turn off the Product and disconnect all test
leads, patch cords, and cables before you
replace the battery.
Be sure that the battery polarity is correct to
prevent battery leakage.
Do not disassemble or crush battery cells
and battery packs.
Do not operate the Product with covers
removed or the case open. Hazardous
voltage exposure is possible.
Remove the input signals before you clean
the Product.