Installation Manual

ManualsBrandsFluke ManualsElectrical TestersTest Lead Set, 2 Pieces, Use With Electrical Tester

713 English Instruction Sheet

Page

713

Pressure Calibrator

Instruction Sheet

Introduction

Fluke Model 713 30G and 713 100G Pressure Calibrators

(hereafter called “calibrator”) calibrate P/I (pressure to current)

transmitters, or measure pressure or current. The calibrator

simultaneously displays pressure and current measurements.

Full scale pressure input is as follows:

• Model 713 30G: 30 psi (206.85 kPa, 2.0685 bar)

• Model 713 100G: 100 psi (689.5 kPa, 6.895 bar)

The calibrator measures and displays current up to 24 mA, and

the pressure applied to the 1/8-inch NPT pressure fitting. The

calibrator measures pressure in the units shown in the next table.

Your calibrator is supplied with a Flex-Stand holster, an

installed 9 V alkaline battery, one set of TL75 test leads, one set

of AC70A alligator clips, and this instruction sheet.

If the calibrator is damaged or something is missing, contact the

place of purchase immediately. Contact your Fluke distributor for

information about accessories. See “How to Contact Fluke.” To

order replacement parts or spares, see “Replacement Parts.”

PN 650298 August 1997 Rev. 1, 10/97

All product names are trademarks of their respective companies.

Summary of content (16 pages)

PAGE 1
713 English Instruction Sheet Page 1 ® 713 Pressure Calibrator Instruction Sheet Introduction Fluke Model 713 30G and 713 100G Pressure Calibrators (hereafter called “calibrator”) calibrate P/I (pressure to current) transmitters, or measure pressure or current. The calibrator simultaneously displays pressure and current measurements. Full scale pressure input is as follows: • Model 713 30G: 30 psi (206.85 kPa, 2.0685 bar) • Model 713 100G: 100 psi (689.5 kPa, 6.
PAGE 2
713 English Instruction Sheet Page 2 Pressure Range and Resolution Displayed Pressure Units Model 713 30G Range and Resolution Model 713 100G Range and Resolution psi 30.000 psi 100.00 psi inH2O at 4°C 830.4 inH2O 2768.0 inH2O inH2O at 20°C 831.9 inH2O 2772.9 inH2O cmH2O at 4°C, 2109.0 cmH2O 7030 cmH2O cmH2O at 20°C 2113.0 cmH2O 7043 cmH2O bar 2.0685 bar 6.895 bar mbar 2068.5 mbar 6895 mbar kPa 206.85 kPa 689.5 kPa inHg 61.080 inHg 203.6 inHg mmHg 1551.3 mmHg 2 2 kg/cm 2.
PAGE 3
713 English Instruction Sheet Page 3 • Remove the test leads from the calibrator before you open the battery door. • Make sure the battery door is closed and latched before you operate the calibrator. • Do not operate the calibrator if it is damaged. • Do not operate the calibrator around explosive gas, vapor, or dust.
PAGE 4
713 English Instruction Sheet Page 4 Hold in fixed position kf01f.eps Explanation of International Symbols The symbols in the table below are used on the calibrator or in this instruction sheet. International Symbols Symbol J Meaning Earth ground I Fuse M Battery W Refer to this instruction sheet for information about this feature. T Double insulated Conforms to relevant Canadian Standards Association directives.
PAGE 5
713 English Instruction Sheet Page 5 Getting Acquainted with the Calibrator Press the green O pushbutton to turn the calibrator on and off. The calibrator displays pressure and current measurements simultaneously. See the figure below. The upper part of the display shows the gage pressure applied to the pressure fitting. Press U to select a different pressure unit. When you cycle the power off and on, the calibrator retains the pressure unit you last used.
PAGE 6
713 English Instruction Sheet Page 6 Pushbutton Functions Pushbutton Function U Selects a different pressure unit. D Turns pressure reading damping on and off. With damping on, the display does not update as quickly. Z Press this to zero the pressure display. Vent the pressure fitting on the calibrator to atmosphere before you press this pushbutton. m Press and hold to read the minimum pressure and current readings since the power was turned on or c was pressed.
PAGE 7
13 English Instruction Sheet Page 7 S I G N A L + – T E S T 713 100G PRESSURE CALIBRATOR UNITS DAMP MIN CLR MAX HOLD ZERO kf02f.
PAGE 8
713 English Instruction Sheet Page 8 Maintenance For maintenance procedures not described in this instruction sheet, or if the calibrator needs repair, contact a Fluke Service Center. In Case of Difficulty • Check the battery, test leads, and pressure tubing. Replace as necessary. • Review this instruction sheet to make sure you are using the calibrator correctly. If the calibrator needs repair, and the calibrator is under warranty, see the warranty statement for terms.
PAGE 9
713 English Instruction Sheet Page 9 Replacing the Battery When the Bsymbol appears on the display, replace the battery with a 9 V alkaline battery. S I G N A L + – T E S T 713 100G UNITS PRESSURE CALIBRATOR DAMP MIN CLR MAX HOLD ZERO it07f.
PAGE 10
713 English Instruction Sheet Page 10 Replacing the Fuse ! Warning To avoid personal injury or damage to the calibrator, use only a 0.125A 250V fast fuse, Littelfuse 2AG. Fuse F1 is probably blown if the mA measurement display reading does not respond to current applied to the current (mA) inputs. Replace the fuse as follows: 1. Remove the test leads and turn the calibrator off. 2. Remove the battery door. 3. Remove the three Phillips-head screws from the case bottom and turn the case over. 4.
PAGE 11
713 English Instruction Sheet Page 11 R O ZE M AX M IN H O LD U N IT S C LR D AM P F1 Snaps kf03f.
PAGE 12
713 English Instruction Sheet Page 12 Replacement Parts and Accessories Replacement Parts Item Description Part or model no. Qty.
PAGE 13
713 English Instruction Sheet Page 13 MP85 S1 F1 OR1 SP1 BT1 MP86 H2, 3, 4 MP89, 90 H5, 6 MP92 Instruction Sheet AC70A Alligator Clips TL75 Test Lead Set Holster kf04c.
PAGE 14
713 English Instruction Sheet Page 14 Specifications Specifications are based on a one year calibration cycle and apply for ambient temperature from +18 °C to +28 °C unless stated otherwise. “Counts” are the number of increments or decrements of the least significant digit. Pressure Input, 713 30G Range Accuracy 30 psi (206.85 kPa) ±0.05% of range Maximum nondestructive pressure: 3X top of range (90 psi, 620 kPa, 6.2 bar) Temperature coefficient: 0.
PAGE 15
713 English Instruction Sheet Page 15 General Specifications Maximum voltage applied between either mA terminal and earth ground or between the mA terminals: 30 V Storage temperature: -40°C to 60°C Operating temperature: -10°C to 55°C Operating altitude: 3000 meters maximum Relative humidity: 95% up to 30°C, 75% up to 40°C, 45% up to 50°C, and 35% up to 55°C Vibration: Random 2 g, 5 Hz to 500 Hz Shock: 1 meter drop test Safety: Certified as compliant to CAN/CSA C22.2 No. 1010.1:1992.
PAGE 16
713 English Instruction Sheet Page 16 How to Contact Fluke To order accessories, receive operating assistance, or get the location of the nearest Fluke distributor or Service Center, call: 1-800-44FLUKE (1-800-443-5853) in U.S.A. and Canada +31-402-678-200 in Europe +1-425-356-5500 from other countries Address correspondence to: Fluke Corporation P.O. Box 9090, Everett, WA 98206-9090 USA Fluke Europe B.V. P.O. Box 1186, 5602 BD Eindhoven The Netherlands Visit us on the World Wide Web at: www.fluke.