2016 ESCAPE Owner’s Manual 2016 ESCAPE Owner’s Manual owner.ford.com ford.ca May 2015 First Printing Owner’s Manual Escape Litho in U.S.A.
The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2015 All rights reserved.
I nf or mat i onPr ovi dedby:
Table of Contents Driver and Passenger Airbags...................36 Front Passenger Sensing System.............37 Side Airbags.....................................................39 Driver Knee Airbag.........................................40 Safety Canopy™............................................40 Crash Sensors and Airbag Indicator........42 Airbag Disposal...............................................43 Introduction About This Manual...........................................7 Symbols Glossary.....
Table of Contents Information Display Control......................69 Heated Steering Wheel...............................69 Hints on Controlling the Interior Climate.........................................................103 Heated Windows and Mirrors..................106 Cabin Air Filter................................................107 Remote Start..................................................107 Wipers and Washers Windshield Wipers.........................................70 Autowipers...........
Table of Contents Refueling..........................................................132 Fuel Consumption........................................134 Emission Control System..........................135 Eco Mode.........................................................167 Steering............................................................168 Load Carrying Transmission Four-Wheel Drive Rear Under Floor Storage..........................170 Luggage Covers.............................................
Table of Contents Ordering Additional Owner's Literature....................................................200 Reporting Safety Defects (U.S. Only)............................................................200 Reporting Safety Defects (Canada Only).............................................................201 Vehicle Care General Information...................................234 Cleaning Products.......................................234 Cleaning the Exterior..................................
Table of Contents Capacities and Specifications - 2.5L....282 Appendices End User License Agreement.................365 Audio System General Information...................................286 Audio Unit - Vehicles With: AM/FM/ CD..................................................................287 Audio Unit - Vehicles With: AM/FM/CD/ SYNC............................................................289 Audio Unit - Vehicles With: AM/FM/CD/ SYNC/Satellite Radio.............................
I nf or mat i onPr ovi dedby: 6 Escape/Kuga (TM2), enUSA, First Printing
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about your vehicle, the greater the safety and pleasure you will get from driving it. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Introduction Brake system Front airbag Cabin air filter Front fog lamps Check fuel cap Fuel pump reset Child safety door lock or unlock Fuse compartment Child seat lower anchor Hazard warning flashers Child seat tether anchor Heated rear window Cruise control Heated windshield Do not open when hot Interior luggage compartment release Engine air filter Jack Engine coolant Keep out of reach of children E71340 E161353 Engine coolant temperature Lighting control Engine oil Low tire pres
Introduction facilities may access or share among them vehicle diagnostic information received through a direct connection to your vehicle when diagnosing or servicing your vehicle. Additionally, when your vehicle is in for service or repair, Ford Motor Company, Ford of Canada, and service and repair facilities may access or share among them data for vehicle improvement purposes. For U.S.
Introduction This data can help provide a better understanding of the circumstances in which crashes and injuries occur.
Introduction REPLACEMENT PARTS RECOMMENDATION CALIFORNIA PROPOSITION 65 WARNING Your vehicle has been built to the highest standards using quality parts. We recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair. You can clearly identify genuine Ford and Motorcraft parts by looking for the Ford, FoMoCo or Motorcraft branding on the parts or their packaging.
Introduction Warranty on Replacement Parts remote insurance company monitoring, remote vehicle diagnostics, telematics or engine reprogramming, may cause interference or damage to vehicle systems. We do not recommend or endorse the use of any non-Ford-approved aftermarket OBD plug-in devices. The vehicle Warranty may not cover damage caused by any non-Ford-approved aftermarket OBD plug-in device.
Introduction are unique to your vehicle. This Owner’s Manual is written primarily for the U.S. and Canadian Markets. Features or equipment listed as standard may be different on units built for Export. Refer to this Owner’s Manual for all other required information and warnings. MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs.
Environment PROTECTING THE ENVIRONMENT You must play your part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim.
Child Safety GENERAL INFORMATION WARNINGS is compatible with and properly installed in your vehicle. To locate a child seat fitting station and CPST, contact the NHTSA toll free at 1-888-327-4236 or go to http://www.nhtsa.dot.gov. In Canada, check with your local St. John Ambulance office for referral to a CPST or for further information, contact your provincial ministry of transportation, locate your local St. John Ambulance office by searching for St.
Child Safety Recommendations for Safety Restraints for Children Child Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger). Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat). Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 ft. 9 in. (1.
Child Safety • Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers, or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). • Using Lap and Shoulder Belts Place the vehicle seat upon which the child seat will be installed in the upright position. Put the safety belt in the automatic locking mode. See Step 5. This vehicle does not require the use of a locking clip.
Child Safety 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. E142875 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. Note: The automatic locking mode is available on the front passenger and rear seats. E142530 3.
Child Safety Using Lower Anchors and Tethers for CHildren (LATCH) 8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle.
Child Safety Use of Inboard Lower Anchors from the Outboard Seating Positions (Center Seating Use) WARNING The standardized spacing for LATCH lower anchors is 11 inches (28 centimeters) center to center. Do not use LATCH lower anchors for the center seating position unless the child seat manufacturer's instructions permit and specify using anchors spaced at least as far apart as those in this vehicle.
Child Safety Combining Safety Belt and LATCH Lower Anchors for Attaching Child Safety Seats Perform the following steps to install a child safety seat with tether anchors: Note: If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off your vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Child Safety recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms). Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat: E142539 3. Clip the tether strap to the anchor as shown. 4.
Child Safety Types of Booster Seats E70710 • E68924 • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child's head (as measured at the tops of the ears) above the top of the seat.
Child Safety E142597 WARNINGS warnings provided by your vehicle manufacturer. A safety seat that is improperly installed or utilized, is inappropriate for your child's height, age, or weight or does not properly fit the child may increase the risk of serious injury or death. If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Child Safety Recommendations for attaching child safety restraints for children Use any attachment method as indicated below by X Restraint Type Combined weight of child and child seat LATCH (lower anchors and top tether anchor) LATCH (lower anchors only) Rear facing Up to 65 lb child seat (29.5 kg) Safety belt Safety belt Safety belt and LATCH only and top (lower tether anchors anchor and top tether anchor) X X Rear facing Over 65 lb child seat (29.
Child Safety The childproof locks are located on the rear edge of each rear door and must be set separately for each door. Left-Hand Side Turn counterclockwise to lock and clockwise to unlock. Right-Hand Side Turn clockwise to lock and counterclockwise to unlock.
Safety Belts PRINCIPLE OF OPERATION WARNINGS Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. WARNINGS Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained.
Safety Belts The safety belt pretensioners are designed to activate in frontal, near-frontal and side crashes, and in rollovers. The safety belt pretensioners on the retractor and anchor at the front seating positions are designed to tighten the safety belts firmly against the occupant's body when activated. This helps increase the effectiveness of the safety belts.
Safety Belts All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first type of locking mode, and the front outboard passenger and rear seat safety belts have both types of locking modes described as follows: Vehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Safety Belts How to Use the Automatic Locking Mode 3. Return the seatback to its desired upright position. For vehicles with rear seats that do not recline or are locked with the seat in its full rear recline position: 1. 2. 3. E142591 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out. 4. 5. Grasp the safety belt webbing at the top of the seatback. Pull the safety belt webbing forward, firmly.
Safety Belts To adjust the shoulder belt height, squeeze the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place. SAFETY BELT HEIGHT ADJUSTMENT WARNING Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt correctly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash.
Safety Belts The system uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the Belt-Minder feature for objects you place in the front passenger seat, only the front seat passengers receive warnings as determined by the front passenger sensing system.
Safety Belts Deactivating and Activating the Belt-Minder Feature 4. While the safety belt warning light is on, buckle and then unbuckle the safety belt. After Step 4, the safety belt warning light flashes for confirmation. • This will switch the feature off for that seating position if it is currently on. • This will switch the feature on for that seating position if it is currently off.
Personal Safety System™ How Does the Personal Safety System Work? The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Supplementary Restraints System The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. PRINCIPLE OF OPERATION WARNINGS Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module.
Supplementary Restraints System Proper Driver and Front Passenger Seating Adjustment DRIVER AND PASSENGER AIRBAGS WARNING WARNINGS Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Supplementary Restraints System E145987 The indicator lamp is located in the center stack of the instrument panel. E142846 The front passenger sensing system is designed to disable (will not inflate) the front passenger frontal airbag under certain conditions: • The front passenger seat is unoccupied. • The system determines an infant is present in a child restraint. • A passenger takes their weight off the seat for a period of time.
Supplementary Restraints System • • • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the passenger airbag status indicator will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled.
Supplementary Restraints System The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above. SIDE AIRBAGS WARNINGS Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deploying airbag.
Supplementary Restraints System DRIVER KNEE AIRBAG A driver's knee airbag is located under the instrument panel. During a crash, the restraints control module may activate the driver's knee airbag based on crash severity and occupant conditions. Under certain crash and occupant conditions, the driver’s knee airbag may deploy but the driver’s front airbag may not activate. As with front and side airbags, it is important to be properly seated and restrained to reduce the risk of death or serious injury.
Supplementary Restraints System WARNINGS All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death. To reduce risk of injury, do not obstruct or place objects in the deployment path of the curtain airbag. E75004 If the curtain airbags have deployed, the curtain airbags will not function again.
Supplementary Restraints System If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash. CRASH SENSORS AND AIRBAG INDICATOR WARNING Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury.
Supplementary Restraints System AIRBAG DISPOSAL Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.
Keys and Remote Controls • • PRINCIPLE OF OPERATION The remote control allows you to: • Remotely lock or unlock the vehicle doors. • Unlock the doors without actively using a key or remote control (intelligent access only). • Remotely open the power liftgate (if equipped). • Remotely start or stop the engine and user pre-set features (if equipped). • Arm and disarm the anti-theft system. • Activate the panic alarm.
Keys and Remote Controls REMOTE CONTROL Integrated Keyhead Transmitters (If Equipped) E138616 Your intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to activate the push-button start system. E142585 Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control.
Keys and Remote Controls Replacing the Battery 3. Insert the new battery. Refer to the instructions inside the transmitter for the correct orientation of the battery. Press the battery down to make sure it is fully in the housing. 4. Snap the battery cover back onto the transmitter. Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.
Keys and Remote Controls Vehicles with automatic climate control can be configured to operate when the vehicle is remote started. See Automatic Climate Control (page 102). 4. Insert a new battery with the + facing downward. Press the battery down to make sure it is fully in the housing. 5. Snap the battery cover back onto the transmitter and install the backup key. Many states and provinces have restrictions for the use of remote start.
Keys and Remote Controls You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running vehicle. 2. Press the remote start button twice. The exterior lamps flash twice. The horn sounds if the system fails to start, unless quiet start is on. Quiet start runs the blower fan at a slower speed to reduce noise. You can switch it on or off in the information display. See (page 88).
MyKey™ Non-configurable Settings PRINCIPLE OF OPERATION The following settings cannot be changed by an admin key user: • Belt-minder. You cannot disable this feature. The audio system will mute when the safety belts are not fastened. • Early low fuel warning. The low-fuel warning activates earlier, giving the MyKey user more time to refuel.
MyKey™ • • • MyKey is successfully created. Make sure you label it so you can distinguish it from the admin keys. Vehicle speed minders. Once you select a speed, it will be shown in the display followed by an audible tone when the set vehicle speed is exceeded. Audio system maximum volume of 45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed sensitive compensated volume (automatic volume control) feature will be disabled. Always on setting.
MyKey™ To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scroll to: Message Action and Description Settings Press the OK button. MyKey Press the OK button. Clear MyKey Press and hold the OK button until the following message displays. All MyKeys Cleared Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.
MyKey™ You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 88). CHECKING MYKEY SYSTEM STATUS To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll to: Message Description Settings Press the OK button. MyKey Press the OK button. Select one of the following: MyKey Dist. Tracks the distance when drivers use a MyKey.
MyKey™ Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system. USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non MYKEY TROUBLESHOOTING Condition I cannot create a MyKey. Potential Causes • • • • I cannot program the configurable settings. • • I cannot clear the MyKeys. • • I lost the only admin key.
MyKey™ Condition Potential Causes I lost a key. Program a spare key. See Passive Anti-Theft System (page 65). MyKey distances do not accumulate. • • • No MyKey functions with the keyless entry transmitter. • • The MyKey user is not using the MyKey. An admin key holder cleared the MyKeys and created new MyKeys. The key system has been reset. An admin transmitter is present at vehicle start. No MyKeys are created. See Creating a MyKey (page 50).
Locks Press and hold both the lock and unlock buttons on the remote control for four seconds to disable or enable two-stage unlocking. Disabling two-stage unlocking allows all vehicle doors to unlock with one press of the button. The turn signals will flash twice to indicate a change to the unlocking mode. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access.
Locks Right-Hand Side Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Turn counterclockwise to lock. Opening a Rear Door from Inside Press twice within three seconds to: Pull the interior door release handle twice to unlock and open a rear door. The first pull unlocks the door and the second pull will unlatch the door. E138630 • • unlatch a manual liftgate open, close or stop the movement of a power liftgate.
Locks When you lock your vehicle using the power door lock control (with the door open, vehicle in park and ignition off), your vehicle will search for an intelligent access key in the passenger compartment after you close the door. If your vehicle finds a key, all of the doors will immediately unlock. After locking the doors with the lock sensor, there is a brief delay before you can unlock your vehicle. This delay lets you pull the handle to make sure it locked.
Locks Autounlock: Press the power door lock button then the unlock button. The horn will sound once if disabled or twice (one short and one long) if enabled.
Locks Opening the Liftgate Accessory Mode Battery Saver for Intelligent Access Keys (If Equipped) Manually If you leave the ignition on after leaving your vehicle, it will shut off 15 minutes after you close all of the doors. MANUAL LIFTGATE WARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed.
Locks POWER LIFTGATE (If Equipped) • WARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Make sure everyone in your vehicle is in a seat and properly using a safety belt. Failure to follow this warning could result in serious personal injury or death.
Locks With the Outside Control Button Opening the Liftgate 1. Unlock the liftgate with the remote control or power door unlock control. If an intelligent access key is within 3 ft (1 m) of the liftgate, the liftgate unlocks when you press the liftgate release button. E138636 Press and release the liftgate control button. Stopping the Liftgate Movement You can stop the liftgate movement by doing any of the following: • Pressing the liftgate control button.
Locks Hands-Free Feature (If Equipped) 3. Press and hold the liftgate control button on the liftgate until a tone sounds, indicating programming is complete. Note: You can only use the liftgate control button to program the height. Make sure you have an intelligent access transmitter within 3 ft (1 m) of the liftgate. 2 Note: You cannot program the height if the liftgate position is too low. The new open liftgate height is recalled when the power liftgate is opened.
Locks 1. Enter the factory-set code. 2. Press 1·2 on the keypad within five seconds. 3. Enter your personal five-digit code. You must enter each number within five seconds of each other. 4. Press 1·2 on the keypad to save personal code 1. KEYLESS ENTRY (If Equipped) SECURICODE™ KEYLESS ENTRY KEYPAD The keypad is located near the driver window. It is invisible until touched and then it lights up so you can see and touch the appropriate buttons.
Locks The anti-scan feature will turn off after: • one minute of keypad inactivity • pressing the unlock button on the remote control • switching the ignition on • unlocking the vehicle using intelligent access. Unlocking and Locking the Doors To Unlock the Driver Door Enter the factory-set five-digit code or your personal code. You must press each number within five seconds of each other. The interior lamps will illuminate. Note: All doors will unlock if the two-stage unlocking feature is disabled.
Security Replacement Keys PASSIVE ANTI-THEFT SYSTEM Note: Your vehicle comes equipped with two integrated keyhead transmitters or two intelligent access keys. Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote control.
Security You must have two previously programmed coded keys and the new unprogrammed key readily accessible. See your authorized dealer to have the spare key programmed if two previously programmed coded keys are not available. Programming a Spare Intelligent Access Key See your authorized dealer to have additional keys programmed to your vehicle. Read and understand the entire procedure before you begin. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 108). 2 3 E95179 3. Lock the steering column. AUDIO CONTROL (If Equipped) 1 Select the required source on the audio unit. 2 E95178 1. Unlock the steering column. 2. Adjust the steering wheel to the desired position.
Steering Wheel You can operate the following functions with the control: VOICE CONTROL (If Equipped) A B D E186192 Press the control to select or deselect voice control. See SYNC supplement. C CRUISE CONTROL E159789 A Volume up. B Seek up, next or end call. C Volume down. D Seek down, previous or accept call. Seek, Next or Previous Press the seek button to: • Tune the radio to the next or previous stored preset. • Play the next or the previous track. E142437 See Cruise Control (page 161).
Steering Wheel INFORMATION DISPLAY CONTROL E130248 See Information Displays (page 88). HEATED STEERING WHEEL (If Equipped) Press the button to switch the heated steering wheel on and off. Note: You can locate the heated steering wheel control under the climate controls.
Wipers and Washers Intermittent Wipe WINDSHIELD WIPERS Note: Fully defrost the windshield before you switch the windshield wipers on. Note: Make sure you switch the windshield wipers and vehicle power off before using an automatic car wash. Note: If streaks or smears appear on the windshield, clean the windshield and the wiper blades. See Checking the Wiper Blades (page 223). If that does not resolve the issue, install new wiper blades. See Changing the Wiper Blades (page 223).
Wipers and Washers Use the rotary control to adjust the sensitivity of the rain sensor: • Rotate the control down to low sensitivity, and the wipers turn on when the rain sensor detects a large amount of moisture on the windshield. • When you move the wiper lever up to the first position and the autowiper system is on, the autowiper sensitivity setting adjusts the wiper speed according to the moisture on the windshield only. • When you lower the sensitivity, the wipers remain in their ready position only.
Wipers and Washers Note: If you switch autolamps on in conjunction with autowipers, your low beam headlamps turn on automatically when the rain sensor activates the windshield wipers continuously. See Autolamps (page 74). Keep the outside of the windshield clean. The rain sensor is very sensitive. If the area around the mirror is dirty, then the wipers may operate if dirt, mist or insects hit the windshield.
Wipers and Washers When you switch on the front wipers and move the gearshift lever to reverse (R), rear intermittent wipe automatically turns on. Rear Window Washer E197529 Push the lever away from you to operate the rear window washer. When you release the lever, wiping continues for a short period of time.
Lighting Headlamp Flasher LIGHTING CONTROL E162680 E142449 Pull the lever toward you slightly and release it to flash the headlamps. A Off B Parking lamps, instrument panel lamps, license plate lamps and tail lamps C AUTOLAMPS (If Equipped) Headlamps WARNING The autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog. Always ensure that your headlamps are switched to auto or on, as appropriate, during all low visibility conditions.
Lighting If equipped, the following also activate when the lighting control is in the autolamps position and you switch them on in the information display: • Configurable daytime running lamps. • Automatic high beam control. • Adaptive headlamp control. INSTRUMENT LIGHTING DIMMER The headlamps remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps remain on. See Information Displays (page 88).
Lighting 3. The transmission is not in park (P) for vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions. 4. The lighting control is in the autolamps position. 5. The headlamps are off. DAYTIME RUNNING LAMPS (If Equipped) WARNING The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting during low visibility driving conditions.
Lighting Rear Interior Lamp (If Equipped) DIRECTION INDICATORS A E142455 E162681 You can switch individual map lamps on independently by pressing switch A. Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. INTERIOR LAMPS The lamps will switch on when: • • You open any door. You press a remote control button. Front Interior Lamp E181171 A. Left-hand lamp. B. Right-hand lamp.
Windows and Mirrors One-Touch Up (If Equipped) POWER WINDOWS Lift the control fully and release it. Press or lift it again to stop the window. WARNINGS Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. Window Lock When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings.
Windows and Mirrors Accessory Delay (If Equipped) 1. Close the window twice until it reaches the point of resistance and let it reverse. 2. Close the window a third time to the point of resistance. You disabled the bounce-back feature and you can now close the window manually. The window travels past the point of resistance and you can close it fully. You can use the window controls for several minutes after switching off the ignition or until opening either front door.
Windows and Mirrors Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 106). C Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Memory Function (page 113).
Windows and Mirrors SUN VISORS INTERIOR MIRROR WARNING Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. E138666 Rotate the sun visor toward the side window and extend it rearward for extra shade.
Windows and Mirrors Press and release the rear of the control to open the moonroof. If it is closed, the sunscreen will automatically open before the moonroof opens. The moonroof will stop short of the fully opened position. WARNINGS When closing the moonroof, you should verify that it is free of obstructions and make sure that children and pets are not in the proximity of the roof opening. Note: This position helps to reduce wind noise or rumbling which may happen with the moonroof fully open.
Instrument Cluster GAUGES E171213 A Information display B Speedometer C Engine coolant temperature gauge D Fuel gauge E Tachometer Use the diagram to determine your magnetic zone. Information Display Compass (If Equipped) Displays the vehicle’s heading direction. To calibrate and set the compass zone use the information display menu. See Information Displays (page 88).
Instrument Cluster Fuel Gauge 3 2 Note: The fuel gauge level may vary slightly when your vehicle is moving or when driving on a slope. 15 1 4 Switch the ignition on. The fuel gauge will indicate approximately how much fuel is in the fuel tank. The arrow next to the fuel pump symbol shows the fuel filler door side of your vehicle. 14 13 5 12 6 E142800 The needle will move toward full when you refuel your vehicle. If the needle still points to empty after adding fuel, have your vehicle repaired.
Instrument Cluster Blind Spot Monitor (If Equipped) Note: The low fuel warning and distance-to-empty warning can appear at different fuel gauge positions depending on fuel economy conditions. This variation is normal. It will illuminate when you switch this feature off or in conjunction E124823 with a message. See Blind Spot Information System (page 162). See Information Messages (page 91).
Instrument Cluster Engine Oil Low Fuel Level If it illuminates with the engine running or when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 217). It will illuminate when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as possible. Note: Do not resume your journey if it illuminates despite the level being correct.
Instrument Cluster AUDIBLE WARNINGS AND INDICATORS WARNING Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Have an authorized dealer service your vehicle immediately. Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition.
Information Displays • GENERAL INFORMATION WARNING • Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible.
Information Displays 1 Trip 1 and 2 Distance to E Trip Odometer Trip Timer Inst Fuel Econ Average Fuel Anticipation 2 Ford EcoMode Speed Average Speed Digital Speedo All Value - Distance to E, Trip Odometer, Instantaneous Fuel and Average Fuel 1 See Trip Computer (page 91). 2 See Eco Mode (page 167). Information Seatbelt Intelligent 4WD MyKey Dist.
Information Displays Settings Daytime Running Light On or Off Navigation info On or Off Language Choose your applicable setting Distance Choose your applicable setting Temperature Choose your applicable setting Chimes Park Slot On or Off Convenience Auto engine off On or Off Compass Display On or Off Remote Start Climate Control Heater – A/C / Auto or Last Settings Display Front Defrost / Auto or Off Rear Defrost / Auto or Off Duration (5, 10 or 15 minutes) Quiet Start On/Off Res
Information Displays System Check All Value All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/down arrow buttons to scroll through the list. Indicates all the respective remaining fuel, distance, time and average fuel information. INFORMATION MESSAGES Note: Depending on your vehicle options and instrument cluster type, not all of the messages display or are available.
Information Displays A system specific symbol with a message indicator may supplement some messages. Airbag Message Message Indicator Action Airbag fault Service now Amber Displays when the system requires service due to a malfunction. Contact your authorized dealer. Message Message Indicator Action Alarm activated Check Vehicle Amber Displays when the alarm has been triggered due to unauthorized entry. See Anti-Theft Alarm (page 66).
Information Displays Battery and Charging System Message Message Indicator Action Electrical system overvoltage Stop safely Red Stop your vehicle as soon as it is safe to do so and switch off the ignition. Contact your authorized dealer. Battery low See manual Amber Displays to warn of a low battery condition. Turn off all unneeded electrical accessories. Contact your authorized dealer.
Information Displays Doors Message Message Indicator Action X door open Red Displays when the door(s) listed is not completely closed and the vehicle is moving. - Displays when the door(s) listed is not completely closed. Red Displays when the luggage compartment is not completely closed and the vehicle is moving. - Displays when the luggage compartment is not completely closed. Red Displays when the hood is not completely closed and the vehicle is moving.
Information Displays Hill Start Assist Message Message Indicator Action Hill start assist not available Amber Displays when hill start assist is not available. Contact your authorized dealer. Message Message Indicator Action Ford KeyFree Key inside vehicle Amber Displays to remind you that the key is in the trunk. See Keyless Starting (page 124). Ford KeyFree No key detected - Displayed if the key is not detected by the system. See Keyless Starting (page 124). Switch ign.
Information Displays Lighting Message Message Indicator Action Brake lamp Bulb fault - Displays when the brake lamp bulb has burned out. Contact your authorized dealer. Low beam Bulb fault - Displays when the low beam headlamp bulb has burned out. Contact your authorized dealer. Headlamp fault Service required Amber Displays when an electrical system problem occurs with the headlamp system. Contact your authorized dealer.
Information Displays Message Message Indicator Action MyKey Check Speed Drive Safely - Displays when MyKey is active. MyKey Buckle Up to Unmute Audio - Displays when a MyKey is in use and BeltMinder is activated. MyKey Park aid cannot be deactivated - Displays when a MyKey is in use and park aid is activated. Key is Already a MyKey - Displays when trying to create a MyKey with a key already designated as a MyKey.
Information Displays Power Steering Message Message Indicator Action Steering loss Stop safely Red The power steering system is not working. Stop the vehicle a safe place. Contact your authorized dealer. Steering assist fault Service required Amber The power steering system is not working. Stop the vehicle a safe place. Contact your authorized dealer.
Information Displays Message Message Indicator Action Transmission Hot Wait ... - Transmission is hot. Wait as needed to let it cool. 4WD fault Service required Amber The system is not functioning correctly and defaulted to front-wheel drive. See your authorized dealer. See Using Four-Wheel Drive (page 141). 4WD Off Amber Displays when the system disables automatically and enters front-wheel drive only mode to protect driveline components. See Using FourWheel Drive (page 141).
Information Displays Tire Pressure Monitoring System Message Message Indicator Action Low Tire Pressure Amber Displays when one or more tires on your vehicle have low tire pressure. See Tire Pressure Monitoring System (page 258). Tire Pressure Monitor Fault Amber Displays when the tire pressure monitoring system is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer. See Tire Pressure Monitoring System (page 258).
Climate Control MANUAL CLIMATE CONTROL A B C D E E141421 A Fan speed control: Adjust the volume of air circulated in the vehicle. B Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle.
Climate Control AUTOMATIC CLIMATE CONTROL E141422 A AUTO: Press the button to switch on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature. B Fan speed control: Adjust the volume of air circulated in the vehicle. C Power: Press the button to switch the system on and off.
Climate Control Note: Recirculated air may turn off automatically (or be prevented from turning on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated air may also turn on and off automatically in Panel or Panel and Floor airflow modes during hot weather in order to improve cooling efficiency. G Air distribution control: Adjust the control to turn airflow from the windshield, instrument panel, or footwell vents on or off.
Climate Control Note: To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on. Automatic Climate Control Note: Adjusting the settings when your vehicle interior is extremely hot or cold is not necessary. The system automatically adjusts to heat or cool the cabin to your selected temperature as quickly as possible. For the system to function efficiently, the instrument panel and side air vents should be fully open.
Climate Control Cooling the Interior Quickly Vehicle with manual climate control 1 Adjust the fan speed to the highest speed setting. 2 Adjust the temperature control to the MAX A/C position. 3 Adjust the air distribution control to the instrument panel air vents position. Vehicle with automatic climate control Press the MAX A/C button. Recommended Settings for Cooling Vehicle with manual climate control Vehicle with automatic climate control 1 Adjust the fan speed to the second speed setting.
Climate Control Side Window Defogging in Cold Weather Vehicle with manual climate control Vehicle with automatic climate control 1 Adjust the air distribution control to the Press the windshield defrosting and instrument panel and floor air vents defogging button. positions. 2 Press the A/C button. 3 Adjust the temperature control to the desired setting. 4 Adjust the fan speed to the highest setting. 5 Direct the instrument panel side air vents toward the side windows.
Climate Control Automatic Settings CABIN AIR FILTER You can set the climate control to operate in AUTO mode through the information display setting: Remote Start > Climate Control > Heater-A/C > Auto. The climate control system automatically sets the interior temperature to 72°F (22°C). Your vehicle is equipped with a cabin air filter, which gives you and your passengers the following benefits: • It improves your driving comfort by reducing particle concentration.
Seats We recommend that you follow these guidelines: • Sit in an upright position with the base of your spine as far back as possible. • Do not recline the seatback more than 30 degrees. • Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. • Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 in (25 cm) between your breastbone and the airbag cover.
Seats The head restraints consist of: WARNINGS Install the head restraint properly to help minimize the risk of neck injury in the event of a crash. Note: Adjust the seatback to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position.
Seats Removing the Head Restraint MANUAL SEATS 1. Pull the head restraint up until it reaches its highest position. 2. Press and hold buttons C and D. 3. Pull the head restraint up. WARNING Do not adjust the driver seat or seatback when your vehicle is moving. Installing the Head Restraint Moving the Seat Backward and Forward Align the steel stems into the guide sleeves and push the head restraint down until it locks. Folding the Head Restraint 1. Press and hold button E. 2. Pull it back up to reset.
Seats Adjusting the Height of the Driver Seat WARNING Do not place cargo or any objects behind the seatback before returning it to the original position. Pull on the seatback to make sure that it has fully latched after returning the seatback to its original position. An unlatched seat may become dangerous if you stop suddenly or have a crash. POWER SEATS (If Equipped) WARNINGS Do not adjust the driver's seat or seatback when your vehicle is moving.
Seats E138647 I nf or mat i onPr ovi dedby: 112 Escape/Kuga (TM2), enUSA, First Printing
Seats Power Lumbar (If Equipped) E142554 Saving a PreSet Position 1. Switch the ignition on. 2. Adjust the seat and exterior mirrors to your desired position. 3. Press and hold the desired memory button until you hear a single tone. E138648 MEMORY FUNCTION (If Equipped) Recalling a Pre-Set Position WARNINGS Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts.
Seats REAR SEATS HEATED SEATS (If Equipped) WARNING People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
Seats REAR SEAT ARMREST (If Equipped) E138656 Fold the armrest down to use the armrest and cupholder.
Universal Garage Door Opener (If Equipped) HomeLink Wireless Control System WARNINGS Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. E142657 Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).
Universal Garage Door Opener (If Equipped) To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com, www.youtube.com/HomeLinkGentex or 1-800-355-3515. Programming Your Garage Door Opener Motor E142658 1. With your vehicle parked outside of the garage, turn your ignition to the on position, but do not start your vehicle. 2. Hold your hand-held garage door transmitter 2–6 in (5–14 cm) away from the HomeLink button you want to program. 3.
Universal Garage Door Opener (If Equipped) Gate Operator / Canadian Programming 1. Press and hold the outer two function buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly. 2. When the indicator lights flash, release the buttons. The codes for all buttons are erased.
Universal Garage Door Opener (If Equipped) 1. Press and hold the previously programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green. 2. Press the same button twice to confirm the change. If done correctly the indicator light will turn green. A Programming HomeLink to the Genie Intellicode Garage Door Opener Motor B Note: You may need a ladder to access the garage door opener motor. E142661 A. Red indicator light B.
Universal Garage Door Opener (If Equipped) 5. Press and hold the previously programmed button on the visor for 2 seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete. Clearing a HomeLink Device To erase programming from the three HomeLink buttons press and hold the two outer HomeLink buttons until the indicator light begins to flash. The indicator light will begin flashing in 10 to 20 seconds, at which time both buttons should be released.
Auxiliary Power Points 12 Volt DC Power Point Locations WARNINGS Do not plug optional electrical accessories into the cigar lighter socket. Incorrect use of the cigar lighter can cause damage not covered by the vehicle warranty, and can result in fire or serious injury. Power points may be in the following locations: • On the front of the center console. • Inside the center console. • On the rear of the center console. • Inside the luggage compartment.
Auxiliary Power Points When the indicator light on the power point is: • On: The power point is working, the ignition is on and a device is plugged in. • Off: The power point is off, the ignition is off or no device is plugged in. • Flashing: The power point is in fault mode. The power outlet temporarily turns off power when in fault mode if the device exceeds the 150 watt limit. Unplug your device and switch the ignition off. Switch the ignition back on, but do not plug your device back in.
Storage Compartments Press near the rear edge of the door to open it. CENTER CONSOLE Stow items in the cup holder carefully as items may become loose during hard braking, acceleration or crashes, including hot drinks which may spill. Available console features include: A B C E142433 A Cup holder. B Storage compartment with auxiliary power point, auxiliary input jack, USB port and media hub. C Auxiliary power point.
Starting and Stopping the Engine GENERAL INFORMATION IGNITION SWITCH (If Equipped) WARNINGS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, creating the risk of fire. E72128 0 (off) - The ignition is off.
Starting and Stopping the Engine Ignition Modes Before starting the engine check the following: • Make sure all occupants have fastened their safety belts. • Make sure the headlamps and electrical accessories are off. • Make sure the parking brake is on. • Move the transmission selector lever to position P. • Turn the ignition key to position II. If your vehicle is equipped with a keyless ignition, see the following instructions. Vehicles with an Ignition Key Note: Do not touch the accelerator pedal.
Starting and Stopping the Engine 3-button remote Within 20 seconds of switching the engine off, press the brake pedal and press the button. After 20 seconds have expired, you can no longer restart the engine without the key present inside your vehicle. Once the engine has started, it remains running until you press the button, even if the system does not detect a valid key. If you open and close a door while the engine is running, the system searches for a valid key.
Starting and Stopping the Engine Stopping the Engine When Your Vehicle is Moving You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: • You can reset the timer by interacting with your vehicle (such as pressing the brake pedal or accelerator pedal). • You can temporarily switch off the shutdown feature any time the ignition is on (for the current ignition cycle only). Use the information display to do so.
Starting and Stopping the Engine Guarding Against Exhaust Fumes The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source. WARNING If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately.
Starting and Stopping the Engine • • Make sure the system is unplugged and properly stowed before starting and driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use. Make sure the heater system is checked for proper operation before winter. Using the Engine Block Heater Make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.
Fuel and Refueling • SAFETY PRECAUTIONS WARNINGS Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. • Automotive fuels can cause serious injury or death if misused or mishandled.
Fuel and Refueling • FUEL QUALITY Choosing the Right Fuel • The use of fuels with metallic compounds such as methylcyclopentadienyl manganese tricarbonyl (commonly known as MMT), which is a manganese-based fuel additive, will impair engine performance and affect the emission control system. E161513 Do not be concerned if the engine sometimes knocks lightly.
Fuel and Refueling Filling a Portable Fuel Container 1. Fully open the fuel tank filler door until it engages and remove the fuel tank filler cap. Note: Capless fuel systems do not have a fuel tank filler cap. Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Only use an approved fuel container to transfer fuel to your vehicle. Place the container on the ground when filling it.
Fuel and Refueling Easy Fuel™ Capless Fuel System WARNINGS When refueling always shut the engine off and never allow sparks or open flames near the fuel tank filler valve. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes. WARNING The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops.
Fuel and Refueling If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after 4 or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. FUEL CONSUMPTION E154765 4. Remove the fuel filler nozzle and fully close the fuel tank filler door.
Fuel and Refueling Calculating Fuel Economy WARNINGS Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Fuel and Refueling An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. • • You can correct these temporary malfunctions by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out.
Fuel and Refueling Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, your vehicle is not ready for I/M testing.
Transmission Park (P) AUTOMATIC TRANSMISSION This position locks the transmission and prevents the wheels from turning. WARNINGS Always set the parking brake fully and make sure the gearshift is latched in park (P). Turn the ignition to the off position and remove the key whenever you leave your vehicle. Reverse (R) With the gearshift lever in reverse (R), your vehicle will move backward. Always come to a complete stop before shifting into and out of reverse (R).
Transmission To use SelectShift, move the gearshift lever into sport (S). Use the +/- buttons on the side of your gearshift lever to manually change gears. • • WARNINGS When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure. Use wheel chocks if appropriate. Press the (+) button to upshift. Press the (-) button to downshift.
Transmission 5. While holding the white lever in the rear position, move the shifter from the park position. 6. Press the shifter bezel back into the top finish panel until it snaps back into position. 7. Apply the brake pedal, start the vehicle and release the parking brake. Note: See your authorized dealer as soon as possible if this procedure is used.
Four-Wheel Drive (If Equipped) Note: It is recommended that you reinstall the repaired tire or replace the tire as soon as possible. Major dissimilar tire sizes between the front and rear axles could cause system damage or default the system to front-wheel drive. PRINCIPLE OF OPERATION This system is a proactive system. It has the ability to anticipate wheel slip and transfer torque to the rear wheels before slip occurs.
Four-Wheel Drive (If Equipped) When driving at slow speeds off road under high load conditions, use a low gear when possible. Low gear operation will maximize the engine and transmission cooling capability. in loss of vehicle control. Apply smooth pressure to the accelerator pedal or brake pedal when changes in vehicle speed are required. Avoid abrupt steering, acceleration and braking. This could result in an increased risk of vehicle roll over, loss of vehicle control and personal injury.
Four-Wheel Drive (If Equipped) Avoid driving at excessive speeds, this causes vehicle momentum to work against you and your vehicle could become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Driving on Hilly or Sloping Terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down.
Four-Wheel Drive (If Equipped) Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral. Disengage overdrive or move the transmission selector lever to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. The front wheels have to be turning in order to steer your vehicle. Avoid sudden braking.
Four-Wheel Drive (If Equipped) We recommend that you use caution when your vehicle has either a high load or device (i.e. ladder or luggage racks). Any modifications to your vehicle that raise the center of gravity may cause your vehicle to roll over when there is a loss of vehicle control. Failure to maintain your vehicle correctly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect you and your passenger's safety.
Brakes Emergency Brake Assist GENERAL INFORMATION Emergency brake assist detects when you brake heavily by measuring the rate at which you press the brake pedal. It provides maximum braking efficiency as long as you press the pedal. Emergency brake assist can reduce stopping distances in critical situations. Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and an authorized dealer should check them.
Brakes PARKING BRAKE WARNINGS During all times, you are responsible for controlling your vehicle, supervising the system and intervening, if required. WARNING Always set the parking brake fully and make sure you shift the gearshift lever to park (P). Switch the ignition off and remove the key whenever you leave your vehicle. If the engine is revved excessively, or if a malfunction is detected, the system will be deactivated.
Brakes 2. If the sensors detect that your vehicle is on a slope, the system will activate automatically. 3. When you remove your foot from the brake pedal, your vehicle will remain on the slope without rolling away for about two or three seconds. This hold time will automatically be extended if you are in the process of driving off. 4. Drive off in the normal manner. The brakes will release automatically.
Traction Control Using the Information Display Controls PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. You can switch this feature off or on in the information display. See General Information (page 88). If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time.
Stability Control If a driving condition activates either the stability control or the traction control system you may experience the following conditions: PRINCIPLE OF OPERATION WARNINGS Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel and tire size may change the handling characteristics of your vehicle and may adversely affect the performance of the electronic stability control system.
Stability Control B B B A A B A E72903 A Vehicle without stability control skidding off its intended route. B Vehicle with stability control maintaining control on a slippery surface. USING STABILITY CONTROL AdvanceTrac® with Roll Stability Control™ (RSC®) The system automatically activates when you start your vehicle.
Parking Aids Note: The sensing system cannot be turned off when a MyKey is present. See (page 49). PRINCIPLE OF OPERATION WARNINGS To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving on a flat surface at parking speeds.
Parking Aids E187330 Coverage area of up to 28 in (70 cm) from the front bumper. The coverage area decreases at the outer corners. E130178 Coverage area of up to 6 ft (1.8 m) from the rear bumper. There may be decreased coverage area at the outer corners of the bumper. When your vehicle approaches an object, a warning tone sounds. When your vehicle moves closer to an object, the warning tone repeat rate increases.
Parking Aids Note: The sensors may not detect objects with surfaces that absorb ultrasonic waves or cause ultrasonic interference (motorcycle exhaust, truck air brakes or horns). ACTIVE PARK ASSIST (If Equipped) WARNING Designed to be a supplementary park aid, this system may not work in all conditions. This system cannot replace the driver’s attention and judgment. The driver is responsible for avoiding hazards and maintaining a safe distance and speed, even when the system is in use.
Parking Aids A E130107 Note: If driven above approximately 22 mph (35 km/h), the touchscreen shows a message to alert you to reduce your vehicle speed. When the system finds a suitable space, the touchscreen displays a message and a tone sounds. Slow down, continue moving forward and stop when another tone sounds and a message displays on the touchscreen (at approximately position A), then follow the instructions on the touchscreen.
Parking Aids E130108 • When you think your vehicle has enough space in front and behind it, or you hear a solid tone from the parking aid (accompanied by a touchscreen display message and a chime), bring your vehicle to a complete stop. • • When automatic steering is finished, the touch screen displays a message and a tone sounds, indicating that the active park assist process is done.
Parking Aids The system does not offer a particular space Something may be contacting the front bumper or side sensors There is not enough room on both sides of your vehicle in order to park There is not enough space for the parking maneuver on the opposite side of the parking space The parking space is farther than 4.9 ft (1.5 m) or closer than 15.7 in (0.4 m) away.
Parking Aids REAR VIEW CAMERA (If Equipped) WARNINGS The rear view camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the interior and exterior mirrors for maximum coverage. Objects that are close to either corner of the bumper or under the bumper, might not be seen on the screen due to the limited coverage of the camera system. E142435 The camera is located on the luggage compartment door.
Parking Aids Note: When towing, the camera only sees what you are towing. This might not provide adequate coverage as it usually provides in normal operation and some objects might not be seen. In some vehicles, the guidelines may disappear when you connect the trailer tow connector. A B C D E The camera may not operate correctly under the following conditions: • Nighttime or dark areas if one or both reverse lamps are not operating. • Mud, water or debris obstructs the camera's view.
Parking Aids The fixed and active guidelines fade in and out depending on the steering wheel position. The active guidelines do not display when the steering wheel position is straight. Main Menu Settings Vehicle Always use caution while reversing. Objects in the red zone are closest to your vehicle and objects in the green zone are farther away. Objects are getting closer to your vehicle as they move from the green zone to the yellow or red zones.
Cruise Control Switching Cruise Control On PRINCIPLE OF OPERATION Press and release ON. Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h). The indicator will display in the instrument cluster. E71340 Setting a Speed 1. Accelerate to the desired speed. 2. Press and release SET+. 3. Take your foot off the accelerator pedal.
Driving Aids Note: When a vehicle passes quickly through the blind spot zone, typically fewer than two seconds, the system does not trigger. BLIND SPOT INFORMATION SYSTEM WARNING Using the System To help avoid injuries, NEVER use the Blind Spot Information System as a replacement for using the interior and exterior mirrors or looking over your shoulder before changing lanes. The Blind Spot Information System is not a replacement for careful driving.
Driving Aids The Blind Spot Information System illuminates an amber alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from. When the Blind Spot Information System is alerting on a vehicle and the corresponding turn signal is ON, the Blind Spot Information System alert indicator flashes as an increased warning level. The alert indicator dims when the system detects nighttime darkness.
Driving Aids Switching the System Off and On If the system detects a degraded performance condition, a message warning of a blocked sensor will appear in the information display. Also the BLIS alert indicators will remain ON and BLIS will no longer provide any vehicle warnings. You can clear the information display warning but the alert indicators will remain illuminated. You can temporarily switch the Blind Spot Information System off in the information display. See General Information (page 88).
Driving Aids fully obstructed. Reversing slowly helps increase the coverage area and effectiveness. Cross Traffic Alert is designed to detect vehicles that approach with a speed up to 37 mph (60 km/h). Coverage decreases when the sensors are partially, mostly or E142440 In this first example, the left sensor is only partially obstructed; zone coverage to the right is nearly maximized.
Driving Aids Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited. System Lights, Messages and Audible Alerts E142442 The Cross Traffic Alert illuminates an amber alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from.
Driving Aids Note: The Cross Traffic Alert switches on whenever the ignition is switched on and ready to provide appropriate alerts when the transmission is in reverse (R). Cross Traffic Alert will not remember the last selected on or off setting. The following are other situations that may limit the Cross Traffic Alert performance: • Adjacently parked vehicles or objects obstructing the sensors. • Approaching vehicles passing at speeds greater than 37 mph (60 km/h).
Driving Aids Type 1 STEERING Electric Power Steering WARNINGS The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation. When a system error is detected a steering message will appear in the information display. A E142444 A Anticipation B Efficient speed The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation of the electronic system.
Driving Aids system. If this should occur, you will neither lose the ability to steer the vehicle manually nor will it cause permanent damage. Typical steering and driving maneuvers will allow the system to cool and steering assist will return to normal.
Load Carrying LUGGAGE COVERS REAR UNDER FLOOR STORAGE WARNINGS Make sure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is not securely installed. Cargo Management System (If Equipped) Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of your vehicle in a sudden stop or crash. Use the cargo shade to cover items in the cargo area of your vehicle.
Load Carrying Adjusting the Crossbar (If Equipped) ROOF RACKS AND LOAD CARRIERS Note: For less wind noise and better aerodynamics, only install the crossbars when you need them for carrying cargo. If you prefer to keep the crossbars installed, the front crossbar has two positions. The front position is quieter for wind noise. The rear position may help to reduce wind noise from an open moonroof. Follow the steps to reposition or remove the front crossbar.
Load Carrying vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label: Base Curb Weight - is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment.
Load Carrying authorized-dealer installed equipment on the vehicle, you must subtract the weight of the equipment from the payload listed on the Tire Label in order to determine the new payload. Example only: WARNING The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry).
Load Carrying Cargo Weight - includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) - is the total weight placed on each axle (front and rear) including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) - is the maximum allowable weight that can be carried by a single axle (front or rear).
Load Carrying Example only: E198828 WARNING Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.
Load Carrying Tongue Load or Fifth Wheel King Pin Weight - refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5000 pound (2268 kilogram) conventional trailer, multiply 5000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 pounds (227 to 340 kilograms). For an 11500 pound (5216 kilogram) fifth wheel trailer, multiply by 0.15 and 0.25 to obtain a proper king pin load range of 1725 to 2875 pounds (782 to 1304 kilograms).
Load Carrying 1. Locate the statement "The combined weight of occupants and cargo should never exceed XXX kg or XXX lb." on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lb. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb.
Load Carrying be: 635 kilograms - (2 x 99 kilograms) - (12 x 45 kilograms) = 635 - 198 - 540 = -103 kilograms. You will need to reduce the load weight by at least 240 pounds (104 kilograms). If you remove three 100-pound (45-kilogram) cement bags, then the load calculation would be: 1400 - (2 x 220) - (9 x 100) = 1400 - 440 900 = 60 pounds. Now you have the load capacity to transport the cement and your friend home.
Towing TOWING A TRAILER Load Placement WARNINGS Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest to the trailer floor.
Towing RV & Trailer Towing Guide Online Website http://www.fleet.ford.com/towing-guides/ RECOMMENDED TOWING WEIGHTS TRAILER SWAY CONTROL (If Equipped) Note: Do not exceed the trailer weight for your vehicle configuration listed in the chart below. Note: Be sure to take into consideration trailer frontal area. 2 Do not exceed 20 feet (1.86 2 meters ) if your vehicle is not equipped with a towing package or 2 2 30 feet (2.79 meters ) if your vehicle is equipped with a towing package.
Towing Your vehicle may tow a trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your vehicle configuration on the following chart. Maximum GCWR Maximum trailer 1 weight 2.5L 2WD 5351 lb (2427 kg) 1500 lb (681 kg) 1.
Towing ESSENTIAL TOWING CHECKS Weight-distributing Hitches Follow these guidelines for safe towing: • Do not tow a trailer until you drive your vehicle at least 1000 miles (1600 kilometers). • Consult your local motor vehicle laws for towing a trailer. • See the instructions included with towing accessories for the proper installation and adjustment specifications. • Service your vehicle more frequently if you tow a trailer. See your scheduled maintenance information.
Towing Trailer Brakes 6. Check that the trailer is level or slightly nose down toward your vehicle. If not, adjust the ball height accordingly and repeat Steps 2-6. When the trailer is level or slightly nose down toward the vehicle: • Lock the bar tension adjuster in place. • Check that the trailer tongue securely attaches and locks onto the hitch. • Install safety chains, lighting, and trailer brake controls as required by law or the trailer manufacturer.
Towing Trailer Lamps • When stopped in congested or heavy traffic during hot weather, place the gearshift in position P to aid engine and transmission cooling and to help A/C performance. • Turn off the speed control with heavy loads or in hilly terrain. The speed control may turn off automatically when you are towing on long, steep grades. • Shift to a lower gear when driving down a long or steep hill. Do not apply the brakes continuously, as they may overheat and become less effective.
Towing 4. Place wheel chocks in front and back of the trailer wheels. (Chocks not included with vehicle.) TOWING POINTS Due to local market requirements in some countries, some vehicles may be equipped with a recovery hook. Launching or Retrieving a Boat or Personal Watercraft (PWC) Recovery Hook Location If your vehicle is equipped with a screw-in recovery hook, it is located in the luggage compartment under the floor cover.
Towing Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. Braking and steering efforts are high if the engine is not running. Maintain increased stopping distances. TRANSPORTING THE VEHICLE It is acceptable to have your front-wheel drive vehicle towed from the front if using proper wheel lift equipment to raise the front wheels off the ground.
Towing WARNING If your vehicle has a steering wheel lock make sure the ignition is in the accessory or on position when being towed. Recreational Towing Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. See Climate Control (page 101). Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome.
Driving Hints Avoid these actions; they reduce your fuel economy: • Sudden accelerations or hard accelerations. • Revving the engine before turning it off. • Idle for periods longer than one minute. • Warm up your vehicle on cold mornings. • Use the air conditioner or front defroster. • Use the speed control in hilly terrain. • Rest your foot on the brake pedal while driving. • Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.
Driving Hints • • • • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. Close the windows for high-speed driving. • • • Lightly press the brake pedal to dry the brakes and to check that they work. Check that the horn works. Check that the exterior lights work. Turn the steering wheel to check that the steering power assist works.
Driving Hints WARNINGS Check attachment of floor mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning or replacement. Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects that are loose can become trapped under the pedals causing a loss of vehicle control.
Roadside Emergencies authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km). ROADSIDE ASSISTANCE Vehicles Sold in the United States: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please refer to the coverage section of your warranty guide, call us in Canada at 1-800-665-2006, or visit our website at www.ford.ca. The hazard warning button is located on the instrument panel. Use it when your vehicle is creating a safety hazard for other motorists. • Sykes Assistance Services Corporation administers the Roadside Assistance program.
Roadside Emergencies Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle's electrical system. 3. Remove your foot from the brake pedal and press the START/STOP button to switch off the ignition. 4. You can either attempt to start the engine by pressing the brake pedal and the START/STOP button, or switch on the ignition only by pressing the START/STOP button without pressing the brake pedal. Both ways re-enable the fuel system.
Roadside Emergencies 1 3 E152134 4 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle's engine, or connect the negative (-) cable to the ground connection point, if available. 2 WARNING Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. E142664 1.
Roadside Emergencies POST-CRASH ALERT SYSTEM The system flashes the direction indicators and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag (front, side, side curtain or Safety Canopy) or the safety belt pretensioners. 4 2 The horn and indicators will turn off when: • You press the hazard control button. • You press the panic button on the remote entry transmitter (if equipped). • Your vehicle runs out of power. 1 3 E142665 1.
Customer Assistance These are some of the items that can be found online: • U.S. dealer locator by Dealer Name, City/State or Zip Code. • Owner Manuals. • Maintenance Schedules. • Recalls. • Ford Extended Service Plans. • Ford Genuine Accessories. • Service specials and promotions. GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer.
Customer Assistance In order to help us serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. • Your telephone number (home and business). • The name of the authorized dealer and city where located. • The vehicle’s current odometer reading. California Civil Code Section 1793.
Customer Assistance already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.
Customer Assistance In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada.
Customer Assistance FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Or to order a free publication catalog, call toll free: 1-800-782-4356 Ford: 80004443673 Lincoln: 80004441067 If calling from the UAE: 80004441066 If calling from the Kingdom of Saudi Arabia: 8008443673 If calling from Kuwait: 22280384 www.helminc.com Monday-Friday 8:00 a.m. - 6:00 p.m.
Customer Assistance If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.
Fuses FUSE SPECIFICATION CHART WARNINGS To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. Pre-Fuse Box The pre-fuse box is in the engine compartment attached to the positive battery post. This box contains several high current fuses. If you need to replace one of these high current fuses, see an authorized dealer. The power distribution box is in the engine compartment.
Fuses Fuse or relay number Fuse amp rating Protected components F7 50A** Anti-lock brake system and electronic stability program pump. F8 30A** Electronic stability program valve. F9 — F10 40A** F11 — F12 30A** Powertrain control module relay. F13 30A** Starter relay. F14 25A** Rear power window (without door control unit). F15 20A** Front cigar lighter or power outlet. F16 25A** Front power window (without door control unit). F17 20A** Rear power outlet.
Fuses Fuse or relay number Fuse amp rating Protected components F30 15A* F31 — F32 15A* Vehicle power. Heated mirror (less door control unit). Heated wiper park. Not used. F33 10A* Vehicle power 2. F34 10A* Vehicle power 3. F35 15A* Vehicle power 4. F36 5A* Active grill shutters. F37 10A* Occupant classification sensor. Passenger airbag deactivation indicator. F38 5A* Engine control module and transmission control module ignition feed.
Fuses Fuse or relay number Fuse amp rating Protected components R5 — Not used. R6 — Not used. R7 — Not used. R8 Power relay R9 — R10 Mini relay R11 Micro relay Air conditioner clutch. Cooling fan. Delayed accessory relay. Not used. Starter relay. R12 Power relay R13 Mini relay Heater blower. R14 Mini relay Engine control relay. R15 Power relay Heated rear window. R16 Power relay Ignition 15.
Fuses E129926 Fuse or relay number Fuse amp rating F56 20A Protected components F57 — Not used. F58 5A Not used (spare). Fuel pump supply, Air mass meter. F59 5A Passive anti-theft transceiver. F60 10A Interior light. Driver door switch pack. Glove box light. Overhead console switch bank.
Fuses Fuse or relay number Fuse amp rating Protected components F61 20A F62 5A Rain sensor module. Auto-dimming mirror. F63 10A Not used (spare). F64 — Cigar lighter. Power point. Not used. F65 10A Liftgate release. F66 20A Driver door unlock. F67 7.5A SYNC. Multifunction display. Global positioning system module. F68 — Not used. F69 5A Instrument cluster. F70 20A Central lock and unlock supply. F71 7.5A Heating control head (manual air conditioner).
Fuses Fuse or relay number Fuse amp rating Protected components F81 5A F82 20A Washer pump. F83 20A Central locking. Radio frequency receiver. F84 20A Drive door unlock. F85 7.5A Electronic 15 feed. F86 10A Air bag module. Occupant classification system. Passenger air bag deactivation indicator. F87 15A Not used (spare). F88 25A Supply for F67, F69, F71 and F79. F89 — Not used.
Fuses Fuse or relay number Fuse amp rating Protected components F1 5A Hands-free liftgate entry module. F2 10A Keyless vehicle module. F3 5A Keyless vehicle door handles. F4 25A Door control unit front left. F5 25A Door control unit front right. F6 25A Door control unit rear left. F7 25A Door control unit rear right. F8 25A Passenger seat. F9 25A Driver seat. F10 5A Driver seat memory module logic feed. F11 5A Rear ignition coil feed. F12 — Not used. F13 — Not used.
Fuses Fuse or relay number Fuse amp rating Protected components F27 20A F28 — Not used. F29 5A Blind spot detection system. Rear view camera with park assist. F30 5A Parking aid module. F31 — Not used. F32 5A DC/AC power converter. F33 — Not used. F34 — Not used. Luggage compartment power outlet. F35 — Not used. F36 — Not used. F37 — Not used. F38 — Not used. F39 — Not used. F40 — Not used. F41 — Not used. F42 — Not used. F43 — Not used.
Fuses CHANGING A FUSE Fuses WARNING You must replace a failed fuse with one that has the specified amperage rating. If you use a fuse with a higher amperage rating, you may cause severe wire damage and may start a fire. E142430 A fuse may fail if electrical components in the vehicle are not properly working. A broken wire inside the fuse indicates a failed fuse. Check the appropriate fuses before replacing any electrical components.
Maintenance Working with the Engine Off GENERAL INFORMATION 1. Set the parking brake and shift to park (P). 2. Switch off the engine. 3. Block the wheels. Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of authorized dealers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly.
Maintenance E142458 3. Move the catch to the right to release the hood. E87786 4. Open the hood and support it with the hood strut. Closing the Hood 1. Remove the hood strut from the catch and secure it correctly in the clip. 2. Lower the hood and allow it to drop under its own weight for the last 8-12 in (20-30 cm). Note: Make sure that the hood is correctly closed.
Maintenance UNDER HOOD OVERVIEW - 1.
Maintenance UNDER HOOD OVERVIEW - 2.
Maintenance UNDER HOOD OVERVIEW - 2.
Maintenance 2. Check the oil level before starting the engine, or switch the engine off and wait 15 minutes for the oil to drain into the oil pan. 3. Remove the dipstick and wipe it with a clean, lint free cloth. Replace the dipstick and remove it again to check the oil level. ENGINE OIL DIPSTICK - 1.6L ECOBOOST™ A B If the oil level is at the minimum mark, add oil immediately. See Capacities and Specifications (page 268). E188072 A Minimum. B Maximum.
Maintenance Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers. WARNINGS Do not put engine coolant in the windshield washer fluid container.
Maintenance • Note: Coolant expands when it is hot. The level may extend beyond the MAX mark. Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately. See Adding Engine Coolant in this chapter. • The coolant concentration should be maintained within 48% to 50%, which equates to a freeze point between -30°F (-34°C) and -34°F (-37°C). Unscrew the cap slowly. Any pressure will escape as you unscrew the cap.
Maintenance Severe Climates The service engine soon indicator will light. If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%. • A coolant concentration of 60% will provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance You have limited engine power when in the fail-safe mode, so drive your vehicle with caution. Your vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid.
Maintenance Note: If your vehicle's battery has a cover or shield, make sure it is reinstalled after the battery has been cleaned or replaced. FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. Note: See an authorized dealer for low voltage battery access, testing, or replacement.
Maintenance Note: If you do not allow the engine to relearn the idle and fuel trim strategy, the idle quality of your vehicle may be adversely affected until the engine computer eventually relearns the idle trim and fuel trim strategy. Because your vehicle’s engine is electronically-controlled by a computer, some engine control settings are maintained by power from the low voltage battery.
Maintenance 2. Install in the reverse order. Note: Make sure that the wiper blade locks into place. 1 ADJUSTING THE HEADLAMPS Vertical Aim Adjustment 1 E129990 The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer. 2 1. Press the locking buttons together. 2. Remove the wiper blade. 3. Install in the reverse order. Note: Make sure that the wiper blade locks into place.
Maintenance Note: To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 5. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver, turn the adjuster either clockwise or counterclockwise in order to aim the headlamp. The horizontal edge of the brighter light should touch the horizontal reference line. 6. Close the hood and turn off the lamps. 3.
Maintenance 4. There is a distinct cut-off (change from light to dark) in the left portion of the beam pattern. The top edge of this cut-off should be positioned two inches (5 centimeters) below the horizontal reference line. 1. Switch all of the lamps and the ignition off. 2. Remove the screws that secure the lamp assembly. 3. Pull the headlamp toward the front of your vehicle to disengage it from its locating points and then lift the headlamp up. 4. Disconnect the electrical connector.
Maintenance Replacing Headlamp Bulbs 2 WARNING 4 Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb by only its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. E142470 1. 2. 3. 4. Headlamp: A B C Remove the headlamp. Remove service cap.
Maintenance Replacing Fog, Park and Turn Signal Bulbs Install the new bulbs in reverse order from the steps above. Be sure that the spring clip is not damaged or detached from the headlamp assembly during the replacement procedure. A B C Replacing HID Headlamp Bulbs (If Equipped) The low beam headlamps on your vehicle use a high intensity discharge source. These lamps operate at a high voltage.
Maintenance 1. Make sure the headlamp control is in the off position and open the liftgate. 2. Remove the two bolt covers using a standard flat tip screwdriver. 3. Remove the two bolts from the lamp assembly. 4. Gently pull the lamp assembly away from the vehicle. E142799 2. Remove the bulb holder from the lamp assembly by turning it counterclockwise. 3. Disconnect the electrical connector. 4. Remove the bulb from the bulb holder by pulling it straight out.
Maintenance Replacing License Plate Lamp Bulb Replacing High-Mount Brake Lamp Bulb Your vehicle is equipped with an LED center high-mount stop lamp located in the spoiler. It is designed to last the life of the vehicle. If replacement is required, see your authorized dealer. 2 1 3 BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.
Maintenance Function Trade number * High-mount brake lamp LED * Interior lamps LED * To replace these lamps - see your authorized dealer.
Maintenance 1. Loosen the four fasteners and remove the air cleaner assembly lid. 2. Remove the air filter element from the air filter housing. 3. Wipe any dirt or debris from the air cleaner assembly to make sure no dirt gets in the engine and to make sure you have a good seal. CHANGING THE ENGINE AIR FILTER WARNING To reduce the risk of vehicle damage and personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running.
Maintenance Note: Make sure you align the tab in the air filter element with the fork in the air cleaner assembly tray. 5. Install the air cleaner assembly lid and tighten the four fasteners. 2.5L Engine E142711 1. 2. 3. 4. 5. 6. Detach the 2 clips that secure the air filter cover to the housing. Carefully remove the air filter cover from the housing. Do not detach any connections or tubes from the cover. Remove the air cleaner from the housing.
Vehicle Care GENERAL INFORMATION CLEANING THE EXTERIOR Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, we recommend Motorcraft Detail Wash.
Vehicle Care Note: Never use abrasive materials, for example steel wool or plastic pads as they can scratch the chrome surface. • Note: Do not use chrome cleaner, metal cleaner or polish on wheels or wheel covers. Exterior Plastic Parts For routine cleaning we recommend Motorcraft Detail Wash. If tar or grease spots are present, we recommend Motorcraft Bug and Tar Remover.
Vehicle Care • • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations. Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine. CLEANING THE INTERIOR WARNINGS Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents.
Vehicle Care 1. CLEANING THE INSTRUMENT PANEL AND INSTRUMENT CLUSTER LENS 2. WARNING Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. 3. Note: Follow the same procedure as cleaning leather seats for cleaning leather instrument panels and leather interior trim surfaces. See Cleaning Leather Seats (page 237). 4.
Vehicle Care Note: Industrial-strength or heavy-duty cleaners in combination with brush agitation to remove brake dust and dirt, could wear away the clear coat finish over a period time. You should: • Remove dust and loose dirt with a vacuum cleaner. • Clean and treat spills and stains as soon as possible. Note: Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergents.
Vehicle Care General • • • • Store all vehicles in a dry, ventilated place. Protect from sunlight, if possible. If vehicles are stored outside, they require regular maintenance to protect against rust and damage. • Fuel system • Body • • • • • • • Wash your vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and the underside of front fenders. Periodically wash your vehicle if it is stored in exposed locations.
Vehicle Care Miscellaneous • • Make sure all linkages, cables, levers and pins under your vehicle are covered with grease to prevent rust. Move vehicles at least 25 ft (7.5 m) every 15 days to lubricate working parts and prevent corrosion. Removing Vehicle From Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on window surfaces. • Check windshield wipers for any deterioration.
Wheels and Tires Notice to utility vehicle and truck owners GENERAL INFORMATION Use only approved wheel and tire sizes, using other sizes could damage your vehicle. If you change the diameter of the tires from that fitted at the factory, the speedometer may not display the correct speed. Take your vehicle to an authorized Ford dealer to have the system reprogrammed. If you intend to change the size of the wheels from that fitted by the manufacturer, you can check the suitability with an authorized dealer.
Wheels and Tires On some four-wheel drive vehicles, the initial shift from two-wheel to four-wheel drive while the vehicle is moving can cause a momentary clunk and ratcheting sound. These sounds are normal and are not cause for concern. Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Wheels and Tires E168583 E145299 • • • Higher - to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components. Shorter - to give it the capability to approach inclines and drive over the crest of a hill without getting hung up or damaging underbody components. All other things held equal, a shorter wheelbase may make your vehicle quicker to respond to steering inputs than a vehicle with a longer wheelbase.
Wheels and Tires U.S. Department of Transportation Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. TIRE CARE Information About Uniform Tire Quality Grading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Wheels and Tires Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Wheels and Tires Information Contained on the Tire Sidewall *kPa: Kilopascal, a metric unit of air pressure. *PSI: Pounds per square inch, a standard unit of air pressure. *Cold tire pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mi (1.6 km).
Wheels and Tires G. H: Indicates the tire's speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h). These ratings are listed in the following chart.
Wheels and Tires Letter rating Speed rating W 168 mph (270 km/h) J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire.
Wheels and Tires *Traction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Wheels and Tires C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual, defined as four tires on the rear axle (a total of six or more tires on the vehicle). D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single, defined as two tires (total) on the rear axle. B A C D E Information on T Type Tires T145/80D16 is an example of a tire size.
Wheels and Tires C. 80: Indicates the aspect ratio which gives the tire's ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D. D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.
Wheels and Tires Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. You will find a Tire Label containing the Ford recommended tire inflation pressure by the tire size and other important information located on the B-Pillar or the edge of the driver’s door.
Wheels and Tires When the tire tread wears down to the same height as these wear bars, the tire is worn out and must be replaced. Age WARNING Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflation pressure) the tires experience throughout their lives. Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall).
Wheels and Tires This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000, the numbers go to four digits. For example, 2501 means the 25th week of 2001.
Wheels and Tires The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the tire pressure monitoring system indicator is flashing, your system is malfunctioning. Your replacement tire might be incompatible with your tire pressure monitoring system, or some component of the system may be damaged. WARNINGS 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again. 3.
Wheels and Tires Highway Hazards Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front-wheel drive vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear.
Wheels and Tires Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. Sometimes irregular tire wear can be corrected by rotating the tires. Vehicles equipped with directional tires Front-wheel drive vehicles E70415 USING SNOW CHAINS WARNING Snow tires must be the same size, load index, speed rating as those originally provided by Ford.
Wheels and Tires • • • • • • • • • • If possible, avoid fully loading your vehicle Purchase chains or cables from a manufacturer that clearly labels body to tire dimension restrictions. Use 10 mm cables or chains only on front axle with 235/55R17 tires. Not all S-class snow chains or cables meet these restrictions. Chains of this size restriction will include a tensioning device. The snow chains or cables must be mounted in pairs on the front axle.
Wheels and Tires Changing Tires With a Tire Pressure Monitoring System Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
Wheels and Tires When Your Temporary Spare Tire is Installed When You Believe Your System is Not Operating Properly When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle. The main function of the tire pressure monitoring system is to warn you when your tires need air.
Wheels and Tires Low tire pressure warning light Possible cause Customer action required Solid warning light Tire(s) under-inflated Make sure tires are at the proper pressure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off.
Wheels and Tires How Temperature Affects Your Tire Pressure Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. The tire pressure monitoring system monitors tire pressure in each pneumatic tire.
Wheels and Tires • 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. • 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY. The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking performance. • Comfort and noise.
Wheels and Tires 5. Remove the jack from the foam holder. The lug wrench is located in the left side storage foam next to the spare tire. Remove the flat tire retainer strap from the jack base. WARNINGS Never get underneath a vehicle that is supported only by a jack. If the vehicle slips off the jack, you or someone else could be seriously injured. Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Wheels and Tires 13. Remove the jack and fully tighten the lug nuts in the order shown. See Technical Specifications (page 266). Stowing the flat tire 1. Put the jack and lug wrench away. Make sure the jack is fastened so it does not rattle when you drive. 2. Unblock the wheels. 3. Stow the flat tire on the floor in the cargo area. Secure with the flat tire retainer strap by following the next steps: E162190 10. Remove the lug nuts with the lug wrench.
Wheels and Tires 5. Weave the retainer strap through the wheel openings. 6. Locate the front cargo tie-down at the opposite corner of the cargo area to the tie-down used in Step 4. Thread the retainer strap through the tie-down and pull tight. 7. Secure by tying a 2-half hitch knot.
Wheels and Tires E145950 A Wheel pilot bore Inspect the wheel pilot bore and mounting surface prior to installation. Remove any visible corrosion or loose particles.
Capacities and Specifications ENGINE SPECIFICATIONS - 1.6L ECOBOOST™ Engine Component 1.6L EcoBoost Engine Cubic inches 98 Required fuel Minimum 87 octane Compression ratio 10.0:1 Spark plug gap 0.027 - 0.031 in. (0.70 - 0.80 mm) Drivebelt Routing 1.6L Ecoboost engine E161372 ENGINE SPECIFICATIONS - 2.0L ECOBOOST™ Engine Component 2.0L EcoBoost Engine Cubic inches 122 Required fuel Minimum 87 octane Compression ratio 9.3:1 Spark plug gap 0.027 - 0.031 in. (0.70 - 0.
Capacities and Specifications Drivebelt Routing A A. The long drivebelt is on the first pulley groove closest to the engine. B. The short drivebelt is on the second pulley groove farthest from engine. B E161383 ENGINE SPECIFICATIONS - 2.5L Engine Component 2.5L Engine Cubic inches 152 Required fuel Minimum 87 octane Compression ratio 9.7:1 Spark plug gap 0.049 - 0.053 in. (1.25 - 1.
Capacities and Specifications Drivebelt Routing A A. The long drivebelt is on the first pulley groove closest to the engine. B. The short drivebelt is on the second pulley groove farthest from the engine. B E161383 MOTORCRAFT PARTS - 1.6L ECOBOOST™ Component 1.
Capacities and Specifications MOTORCRAFT PARTS - 2.0L ECOBOOST™ Component 2.0L EcoBoost Engine Air filter element FA-1908 Oil filter FL-910-S Battery BXT-96R-590 Spark plugs SP-537 Cabin air filter FP-70 Windshield wiper blade WW-2750 (driver side) WW-2705 (passenger side) WW-1106 (rear window) We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance.
Capacities and Specifications MOTORCRAFT PARTS - 2.5L Component 2.5L Engine Air filter element FA-1910 Oil filter FL-910-S Battery BXT-96R-590 Spark plugs SP-530 Cabin air filter FP-70 Windshield wiper blade WW-2750 (driver side) WW-2705 (passenger side) WW-1106 (rear window) We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance. These parts meet or exceed Ford Motor Company’s specifications and are engineered for your vehicle.
Capacities and Specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. E142477 E142476 Please note that in the graphic, XXXX is representative of your vehicle identification number.
Capacities and Specifications VEHICLE CERTIFICATION LABEL TRANSMISSION CODE DESIGNATION E167469 E167814 The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
Capacities and Specifications CAPACITIES AND SPECIFICATIONS - 1.6L ECOBOOST™ Capacities WARNING The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Only qualified personnel should service the air conditioning refrigerant system. Opening the air conditioning refrigerant system can cause personal injury. Item Capacity Engine oil 4.3 qt (4.1 L) Engine coolant 11.1 qt (10.5 L) Brake fluid Between MIN/MAX on brake fluid reservoir Rear differential fluid 2.4 pt (1.
Capacities and Specifications Name Specification MXO-5W20-QSP Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-20 Full Synthetic Motor Oil XO-5W20-QFS WSS-M2C945-A Optional motor oil (Canada): Motorcraft SAE 5W-20 Synthetic Motor Oil CXO-5W20-LFS12 WSS-M2C945-A Engine coolant (U.S.
Capacities and Specifications Name Specification CXT-10-LV12 Windshield washer fluid (U.S. and Mexico): WSS-M14P19-A Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2 Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) WSS-M14P19-A A/C refrigerant (U.S.
Capacities and Specifications If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. • Longer engine cranking periods. • Increased emission levels. • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance.
Capacities and Specifications Item Capacity Engine oil 5.7 qt (5.4 L) Engine coolant 9.7 qt (9.2 L) Brake fluid Between MIN/MAX on brake fluid reservoir Rear differential fluid 2.4 pt (1.15L) Power Transfer Unit (PTU) fluid 17.9 fl oz (0.53 L) Automatic transmission fluid 9.0 qt (8.5 L) Windshield washer fluid Fill as required Fuel tank 15.5 gal (58.7 L) A/C refrigerant 27 oz (0.76 kg) A/C refrigerant compressor oil * * 4.5 fl oz (133 ml) Approximate dry fill capacity.
Capacities and Specifications Name Specification Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B WSS-M97B44-D2 Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B WSS-M97B44-D2 Brake fluid: WSS-M6C65-A2 Motorcraft DOT 4 Low Viscosity (LV) High Performance Motor Vehicle Brake Fluid PM-20 Rear differential fluid (U.S.
Capacities and Specifications Name Specification A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19 WSH-M17B19-A A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R WSH-M17B19-A A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19 WSH-M17B19-A A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D WSH-M1C231-B Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5 ESB-M1C93-B Lock cylinders (U.S.
Capacities and Specifications Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty. Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry.
Capacities and Specifications Item Capacity A/C refrigerant 24 oz (0.68 kg) A/C refrigerant compressor oil * 4.5 fl oz (133 ml) Approximate dry fill capacity. Actual amount may vary during fluid changes. Specifications Materials Name Specification Recommended motor oil (U.S.
Capacities and Specifications Name Specification XT-10-QLVC Automatic transmission fluid (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12 WSS-M2C938-A MERCON LV Windshield washer fluid (U.S. and Mexico): WSS-M14P19-A Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2 Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) WSS-M14P19-A A/C refrigerant (U.S.
Capacities and Specifications Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure.
Audio System AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: • AM: 530, 540-1700, 1710 kHz • FM: 87.9-107.7, 107.9 MHz GENERAL INFORMATION Radio Frequencies and Reception Factors Radio Reception Factors Distance and strength The further you travel from an AM or FM station, the weaker the signal and the weaker the reception.
Audio System • • MP3 folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 tracks on the disc (noted by the .mp3 file extension) and all folders containing MP3 files, from F001 (folder) T001 (track) to F253 T255. Creating discs with only one level of folders helps with navigation through the disc files. In track mode, the system displays and plays the structure as if it were only one level deep (all .
Audio System E172881 A Eject: Press to eject a CD. B Cursor arrows: Press to scroll through on-screen audio system choices, menus or other on-screen functions. C CD slot: Insert a CD. D OK: Press to confirm menu selections. E Clock: Press to set the time. Use the cursor arrows to set the hours and minutes. Press OK to confirm the time. You can also set the clock by pressing MENU and scrolling to Clock Settings. F TUNE: Press to manually search the frequency band.
Audio System H Seek forward: Press and release the right side of the control to go to the next preset radio station or disc track. Press and hold this side of the control to fast forward to the next strong radio station, memory preset or through the current disc track. I ON/OFF: Press to switch the system on and off. Turn to adjust the volume. J Seek reverse: Press and release the left side of the control to go to the previous preset radio station or disc track.
Audio System A B C D E O N F M L K G H H J E162867 I A Eject: Press this button to eject a CD. B Cursor arrows: Press these buttons to scroll through on-screen audio system choices. C OK: Press this button to confirm menu selections. D INFO: Press this button to access any available radio or CD information. E TUNE: Press these buttons to manually search the frequency band. F Number block: In radio mode, store your favorite radio stations.
Audio System J ON/OFF/Volume: Press this button to switch the system off and on. Adjust the control to adjust the volume. K MENU: Press this button to access different audio system features. See Menu Structure later in this section. L SOUND: Press this button to access settings for Treble, Middle, Bass, Fade and Balance. Use the up and down arrow buttons to select the various settings. When you make your selection, press the left and right arrow buttons to change the settings.
Audio System A B C D E P O F N M L G H H K E162869 J I A Eject: Press this button to eject a CD. B Cursor arrows: Press these buttons to scroll through on-screen audio system choices. C OK: Press this button to confirm menu selections. D INFO: Press this button to access any available radio or CD information. E TUNE - and TUNE +: Press these buttons to manually search the frequency band. F Number block: In radio mode, store your favorite radio stations.
Audio System I Sound: Press this button to access settings for Treble, Middle, Bass, Fade and Balance. Use the up and down arrow buttons to select the various settings. When you make your selection, press the left and right arrow buttons to change the settings. Press OK to set or press MENU to exit. Sound settings can be set for each audio source independently. J Seek: Press and release these buttons to go to the previous or next preset radio station or disc track.
Audio System E143843 A TUNE: Press this button to manually search through the radio frequency band. B ON/OFF and VOL: Press this button to switch the audio system off and on. Turn to adjust the volume. C Eject: Press this button to eject a CD. D SEEK: Press this button to go to the next station up or down the radio frequency band or the next or previous track on a CD. E SOUND: Press this button to adjust the sound settings for Bass, Treble, Balance and Fade.
Audio System Note: The CD slot is directly above the touchscreen. AUDIO UNIT - VEHICLES WITH: SONY AM/FM/CD Note: The touchscreen system controls most of the audio features. See SYNC Supplement. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Audio System C Seek, Reverse and Fast Forward: In radio mode, select a frequency band and press these buttons. The system stops at the first station it finds in that direction. In SIRIUS mode, press these buttons to select the previous or next channel. If a specific category is selected (such as Jazz, Rock or News), use these buttons to find the previous or next channel in the selected category. In CD mode, press these buttons to select the previous or next track.
Audio System SIRIUS Scan Select for a brief sampling of all available channels. Show ESN Select to view your satellite radio electronic serial number (ESN). You will need this number when communicating with Sirius to activate, modify or track your account. Channel Guide Select to view available satellite radio channels. Press OK to open a list of the following options for this channel: Tune Channel, Skip Channel or Lock Channel.
Audio System CD Settings Scan All Select to scan all disc selections. Scan Folder Select to scan all music in the current MP3 folder. CD Compression Select to bring soft and loud passages together for a more consistent listening level. Clock Settings Set Time Select to set the time. Set Date Select to set the calendar date. 24h Mode Select to view clock time in a 12-hour mode or 24-hour mode. Display Settings Dimming Select to change display brightness.
Audio System The multicast indicator appears in FM mode (only) if the current station is broadcasting multiple digital broadcasts. The highlighted numbers signify available digital channels where new or different content is available. HD1 signifies the main programming status and is available in analog and digital broadcasts. Other multicast stations (HD2 through HD7) are only available digitally.
Audio System In order to provide the best possible experience, use the contact form to report any station issues found while listening to a station broadcasting with HD Radio technology. Independent entities own and operate each station. These stations are responsible for ensuring all audio streams and data fields are accurate. Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required.
Audio System HD Radio Technology manufactured under license from iBiquity Digital Corp. U.S. and foreign patents. HD Radio and the HD and HD Radio logos are proprietary trademarks of iBiquity Digital Corp. Ford Motor Company and iBiquity Digital Corp. are not responsible for the content sent using HD Radio technology. Content may be changed, added or deleted at any time at the station owner's discretion.
Audio System SIRIUS satellite radio is a subscription-based satellite radio service that broadcasts a variety of music, sports, news, weather, traffic and entertainment programming. Your factory-installed SIRIUS satellite radio system includes hardware and a limited subscription term, which begins on the date of sale or lease of your vehicle. See an authorized dealer for availability.
Audio System Message Questions? Call 1-888-539-7474 None found Check Channel Guide Subscription Updated Condition Action Your satellite service is no longer available. Contact SIRIUS at 1-888539-7474 to resolve subscription issues. All the channels in the Use the channel guide to selected category are either turn off the Lock or Skip skipped or locked. function on that station. SIRIUS has updated the channels available for your vehicle. No action required.
SYNC™ (If Equipped) GENERAL INFORMATION E198355 • SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist and applications, such as Pandora and Stitcher, via SYNC * AppLink. • • • Use the advanced voice recognition system. Charge your USB device (if your device supports this).
SYNC™ (If Equipped) Sunday, 10:30am-7:30pm EST. When using SYNC: • Do not operate playing devices if the power cords or cables are broken, split or damaged. Place cords and cables out of the way, so they do not interfere with the operation of pedals, seats, compartments or safe driving abilities. • Do not leave playing devices in your vehicle during extreme conditions as it could cause them damage. See your device's manual for further information. • Do not attempt to service or repair the system.
SYNC™ (If Equipped) System data cannot be accessed without special equipment and access to the vehicle's SYNC module. Ford Motor Company and Ford of Canada will not access the system data for any purpose other than as described absent consent, a court order, or where required by law enforcement, other government authorities, or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
SYNC™ (If Equipped) System Interaction and Feedback The default setting is to a higher level of interaction in order to help you learn to use the system. You can change these settings at any time. The system provides feedback through audible tones, prompts, questions and spoken confirmations depending on the situation and the chosen level of interaction. You can customize the voice recognition system to provide more or less instruction and feedback. Adjusting the Interaction Level Press the voice button.
SYNC™ (If Equipped) To adjust this setting press the voice button, when prompted say: Voice Command Action and Description voice settings Then any of the following: phone confirmation on When enabled, this feature will prompt you to confirm any voice initiated call command prior to the call being placed. phone confirmation off The system will make a best guess; you may still occasionally be asked to confirm settings.
SYNC™ (If Equipped) 1. Make sure to switch on your phone's Bluetooth feature before starting the search. See your device's manual if necessary. 2. Press the PHONE button. When the audio display indicates there is no paired phone, select the option to add. 3. When a message to begin pairing appears in the audio display, search for SYNC on your phone to start the pairing process. 4. Confirm that the six-digit PIN appearing on your phone matches the six-digit PIN that displays on the SYNC screen.
SYNC™ (If Equipped) 5. Select the option to add. This starts the pairing process. 6. When a message to begin pairing appears in the audio display, search for SYNC on your device. 7. Confirm that the six-digit PIN appearing on your phone matches the six-digit PIN that displays on the SYNC screen. Once you have confirmed the PIN, the display indicates when the pairing is successful..
SYNC™ (If Equipped) Voice Commands Menu Item Plus Hear it Pound (#) Making Calls Star (*) Note: To exit dial mode, press and hold the phone button or press any button on the audio system. E142599 Press the voice button.
SYNC™ (If Equipped) To use the screen to accept a call select: To use the screen to reject a call select: Menu Item Menu Item Reject Accept Ignore the call by doing nothing. Rejecting Calls Phone Options during an Active Call When receiving a call, you can reject the call by pressing the reject call button on the steering wheel or use the screen. During an active call, you have more menu features that become available, such as putting a call on hold or joining calls.
SYNC™ (If Equipped) Menu Item Description and action 4. Press the OK button again when the desired contact appears in the audio display. 5. Press the OK button or dial button to call the selection. Call History Access your call history log. 1. Select the More option. 2. Scroll to the option for call history and press the OK button. 3. Scroll through your call history options (incoming, outgoing or missed). 4. Press the OK button again when the desired selection appears in the audio display. 5.
SYNC™ (If Equipped) Display Description and action Text messaging Send, download and delete text messages. BT Devices Access the option for Bluetooth Device menu listings (add, connect, set as primary, on or off, delete). Phone settings View various settings and features on your phone. Note: This is a speed-dependent feature and is only available when your vehicle is traveling at 3.1 mph (5 km/h) or less. Text Messaging Note: This is a phone-dependent feature.
SYNC™ (If Equipped) Menu Item Description and action Reply to sender Press the OK button to access, and then scroll through a list of pre-defined messages to send. Call sender Press the OK button to call the sender of the message. Forward msg. Press the OK button to forward the message to anyone in your phonebook or call history. You can also choose to enter a number. 2. Select the text messaging option, and then press the OK button. Sending, Downloading and Deleting Your Text Messages 1.
SYNC™ (If Equipped) Accessing Your Phone Settings phonebook, and set up automatic download. These are phone-dependent features. Your phone settings allow you to access and adjust features such as your ring tone and text message notification, modify your 1. Press the PHONE button. 2. Scroll until the phone settings option appears, and then press the OK button.
SYNC™ (If Equipped) Menu Item Phonebook preferences Add contacts Push the desired contacts on your cellular phone. See your device's manual on how to push contacts. Press the OK button to add more contacts from your phonebook. Delete When a message asking you to delete appears, select the option to confirm. Press the OK button to delete the current phonebook and call history. The system takes you back to the menu for phone settings.
SYNC™ (If Equipped) Menu Item Phonebook preferences 4. When the option to set the phone as primary appears, select either yes or no. 5. Depending on the functionality of your phone, the system may prompt you with questions (such as if you want to download your phonebook). Select either yes or no to confirm your responses. Delete Select the delete option and confirm when the system asks to delete the selected device.
SYNC™ (If Equipped) Scroll to select from the following options: Display Description and action Bluetooth on Check or uncheck this option to switch the system's Bluetooth interface off or on. Select this option, and then press the OK button to change the option's status. Set defaults Return to the factory default settings without erasing your indexed information (such as phonebook, call history, text messages and paired devices). Select this option and confirm when prompted in the audio display.
SYNC™ (If Equipped) SYNC™ APPLICATIONS AND SERVICES (If Equipped) Note: The SYNC 911 Assist feature must be set on before the incident. In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone's compatibility, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • 911 Assist: Can alert 911 in the event of an emergency.
SYNC™ (If Equipped) Setting 911 Assist On or Off • Press the phone button to enter the phone menu then select: • Menu Item Action and Description 911 Assist Press OK to confirm and enter the 911 Assist menu. In the Event of a Crash Not all crashes deploy an airbag or activate the fuel pump shut-off (the triggers for 911 Assist).
SYNC™ (If Equipped) 911 Assist Privacy Notice Note: Make sure you have an active account for the app that you have downloaded. Some apps work automatically with no setup. Other apps want you to configure your personal settings and personalize your experience by creating stations or favorites. We recommend you do this at home or outside of your vehicle.
SYNC™ (If Equipped) To Access Using Voice Commands Press the voice button then when prompted say: Menu Item Action and Description Say the name of the application after the tone. The app should start. When an app is running through SYNC, you can press the voice button and speak commands specific to the app, for example "Play Playlist Road Trip". mobile (apps | applications) Help Use this command to discover the available voice commands.
SYNC™ (If Equipped) • • To allow your vehicle to provide location information, including: GPS and speed. To allow the app to send push notifications using the vehicle display and voice capabilities while running in a background state. Push notifications may be particularly useful for news or location based apps. Note: You only need to grant permissions the first time you use an app with SYNC.
SYNC™ (If Equipped) There are three possible statuses: Menu Item Action and Description Update Needed The system has detected a new app requiring authorization or a general permissions update is required. Up-To-Date No update is required. Updating... The system is trying to receive an update. Update settings Menu Item Action and Description Request Update Select this option from the settings menu to manually preform a needed update.
SYNC™ (If Equipped) To Connect Using Voice Commands To Connect Using the System Menu Plug the device into your vehicle's USB port. 1. Plug the device into your vehicle's USB port. 2. Press the AUX button until an "initializing" message appears in the display. Depending on how many media files are on your connected device, an indexing message may appear in the display. When indexing is complete, the screen returns to the playback menu.
SYNC™ (If Equipped) Voice Command Description and Action (USB [stick] | iPod | MP3 You can now play music by saying any of the appropriate [player]) voice commands. You can say any of the voice commands that appear within open and close brackets that are separated by |. For example, where; (what's | what is) appears you say; what's or what is. You must say any of the voice commands that appear outside of open and close brackets.
SYNC™ (If Equipped) Command Description and Action shuffle [all] [on] Plays the current playlist in a random order. (Not all devices support this command.) shuffle off ((who's | who is) this | who plays this | (what's | what is) playing [now] | (what | which) (song | track | artist) is this | (who's | who is) playing | (what's | what is) this) At any time during playback, you can press the voice button and ask the system what is playing.
SYNC™ (If Equipped) Media Menu Features shuffle or repeat), find similar music or reset the index of your USB devices. The media menu allows you to select how to play your music (such as by artist, genre, Message Options Press AUX to select USB playback. Description and Action This will enter the media menu. Then any of the following: Message Description and Action Shuffle Choose to shuffle or repeat your music. Once you make your choice, it remains on until you switch it off.
SYNC™ (If Equipped) If there are media files, you have the following options: Display Play all Description and Action Play all indexed media files from your device one at a time * in numerical order. Press the OK button to select. The first track title appears in the display. Playlists Access your playlists (from formats like ASX, M3U, WPL, * or MTP). 1. Press the OK button to select. 2. Scroll to select the desired playlist, and then press the OK button.
SYNC™ (If Equipped) Display Description and Action 2. Scroll to browse indexed media files on the device, and then press the OK button. Reset USB Resets the USB index. After the new indexing is complete, you can choose what to play from the USB song library. * You can use the buttons at the bottom of the audio display to jump to a certain alphabetical category quickly. You can also use the letters on the audio system's numeric keypad to jump in the list.
SYNC™ (If Equipped) Voice Commands for Audio Sources Voice Command ((who's | who is) this | who plays this | (what's | what is) playing [now] | (what | which) (song | track | artist) is this | (who's | who is) playing | (what's | what is) this) Your voice system allows you to change audio sources with a simple voice command. Help E142599 * Press the voice button and when prompted say: If equipped.
SYNC™ (If Equipped) Voice Command Voice Commands [tune [to]] FM 2 [tune [to]] SAT 3 preset ___ [tune [to]] (FM ___ | ___ [FM]) tune [to] [Sirius] [tune [to]] FM preset ___ Help FM ___ HD ___ [tune [to]] Sirius [channel] ___ [tune [to]] FM 2 preset ___ HD ___ You can say the channel number (0233) to listen to that Sirius station. [tune [to]] preset ___ CD Voice Commands Tune If you are listening to a CD, press the voice button, and then say E142599 any of the commands in the following table.
SYNC™ (If Equipped) SYNC™ TROUBLESHOOTING Voice Command (shuffle | random | mix) (CD [player] | disc) [on] Your SYNC system is easy to use. However, should questions arise, see the tables below. (shuffle | random | mix) folder [on] Use the website at any time to check your phone's compatibility, register your account and set preferences as well as access a customer representative via an online chat (during certain hours). Visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.
SYNC™ (If Equipped) Phone issues Issue Possible cause(s) Possible solution(s) If the missing contacts are stored on your SIM card, try moving them to the device memory. Remove any pictures or special ring tones associated with the missing contact. Depending upon your phone, you may have to grant SYNC permission to access your phonebook contacts. Make sure to confirm when prompted by your phone during the phonebook download. Go to the website to review your phone's compatibility.
SYNC™ (If Equipped) Phone issues Issue Possible cause(s) Possible solution(s) Turn off the Auto phonebook download setting. Text messaging is not working on SYNC. This is a phone-dependent feature. Go to the website to review your phone's compatibility. This may be a possible phone malfunction. Try turning off the device, resetting the device or removing the device's battery, then trying again.
SYNC™ (If Equipped) USB and media issues Issue Possible cause(s) Possible solution(s) The device is not connected. Make sure you correctly connect the device to SYNC, and that you have pressed play on your device. Your music files may not contain the correct artist, song title, album or genre information. SYNC does not recognize music that is on my device. Make sure that all song details are populated. The file may be corrupted. The song may have copyright protection, which does not allow it to play.
SYNC™ (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) You may be saying the name differently than the way you saved it. Say the song or artist exactly as listed. If you say "Play Artist Prince", the system does not play music by Prince and the Revolution or Prince and the New Power Generation. Make sure you are saying the complete title, such as "California remix featuring Jennifer Nettles". If the song titles are in all CAPS, you have to spell them.
SYNC™ (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) The system may not be reading the name the same way you are saying it. The system works better if you list full names, such as "Joe Wilson" rather than "Joe". Contacts in your phonebook Do not use special characters, such as 123 or ICE, as may be very short and similar, or they may contain the system does not recognize them. special characters. Your phonebook contacts may be in CAPS.
SYNC™ (If Equipped) AppLink issues Issue Possible cause(s) Possible solution(s) login on the app on the phone before using them with AppLink. Also, some may have a "Ford SYNC" setting, so check the app's settings menu on the phone. Closing and restarting apps may help SYNC find the application if you cannot discover it inside the vehicle. On an Android device, if apps have an "Exit' or 'Quit' option, select that then restart the app.
SYNC™ (If Equipped) AppLink issues Issue Possible cause(s) Possible solution(s) Unplug the USB cable from the phone, wait a moment, and plug the USB cable My iPhone phone is back in to the phone. After a connected, my app is The USB connection to few seconds, the app should running, I restarted the app SYNC may need to be reset. appear in SYNC's Mobile but I still cannot find it on Apps Menu. If not, "Force SYNC. Close" the application and restart it. I have an Android phone.
Accessories Lifestyle For a complete listing of the accessories that are available for your vehicle, please contact your authorized dealer or visit the online store web site: • • • • • • • • • • • Web Address (United States) www.Accessories.Ford.com Web Address (Canada) www.Accessories.Ford.
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label). Ask an authorized dealer for specific weight information.
Extended Service Plan (ESP) PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRS WITH A FORD EXTENDED SERVICE PLAN. That means you get: • Reliable, quality service at any Ford or Lincoln dealership • Repairs performed by factory trained technicians, using genuine parts SERVICE PLANS (U.S. Only) More than 32 million Ford owners have discovered the powerful protection of Ford Extended Service Plan.
Extended Service Plan (ESP) SERVICE PLANS (CANADA ONLY) Avoid the Rising Cost of Properly Maintaining Your Vehicle! You can get more protection for your vehicle by purchasing a Ford Extended Service Plan. Ford Extended Service Plan is the only service contract backed by Ford Motor Company of Canada, Limited.
Scheduled Maintenance Genuine Ford and Motorcraft® Replacement Parts GENERAL MAINTENANCE INFORMATION Dealerships stock Ford, Motorcraft and Ford-authorized branded re-manufactured replacement parts. These parts meet or exceed our specifications. Parts installed at your dealership carry a nationwide 24-month or unlimited mile (kilometer) parts and labor limited warranty.
Scheduled Maintenance When the oil change message appears in the information display, it is time for an oil change. Make sure you perform the oil change within two weeks or 500 miles (800 kilometers) of the message appearing. Make sure you reset the Intelligent Oil-Life Monitor after each oil change. See (page 88). Additives and Chemicals This owner's manual and the Ford Workshop Manual list the recommended additives and chemicals for your vehicle.
Scheduled Maintenance Check every month Engine oil level. Function of all interior and exterior lights. Tires (including spare) for wear and proper pressure. Windshield washer fluid level. Check every six months Battery connections. Clean if necessary. Body and door drain holes for obstructions. Clean if necessary. Cooling system fluid level and coolant strength. Door weatherstrips for wear. Lubricate if necessary. Hinges, latches and outside locks for proper operation. Lubricate if necessary.
Scheduled Maintenance Multi-Point inspection Accessory drive belt(s) Hazard warning system operation Battery performance Horn operation Engine air filter Radiator, cooler, heater and air conditioning hoses Exhaust system Suspension components for leaks or damage Exterior lamps operation Steering and linkage Tires (including spare) for wear and proper * Fluid levels ; fill if necessary pressure * ** For oil and fluid leaks Windshield for cracks, chips or pits Half-shaft dust boots Washer
Scheduled Maintenance When to expect the message prompting you to change your oil Interval Vehicle use and example Normal Normal commuting with highway driving No, or moderate, load or towing Flat to moderately hilly roads No extended idling 7500-10000 miles (12000-16000 km) Severe Moderate to heavy load or towing Mountainous or off-road conditions Extended idling Extended hot or cold operation 5000-7499 miles (8000-11999 km) Extreme 3000-4999 miles (4800-7999 km) Maximum load or towing Extreme hot
Scheduled Maintenance At every oil change interval as indicated by the information display * Inspect the tires, tire wear and measure the tread depth. Inspect the wheels and related components for abnormal noise, wear, looseness or drag. * Do not exceed one year or 10000 miles (16000 kilometers) between service intervals. ** Reset the Intelligent Oil-Life Monitor after engine oil and filter changes. See Engine Oil Check (page 217).
Scheduled Maintenance Perform the services shown in the following tables when specified or within 3000 miles (4800 kilometers) of the message appearing in your information display prompting you to change your oil. • Example 1: The message comes on at 28751 miles (46270 kilometers). Perform the 30000-mile (48000-kilometer) automatic transmission fluid replacement.
Scheduled Maintenance Extensive idling or low-speed driving for long distances, as in heavy commercial use Every 30000 miles (48000 Change automatic transmission fluid. km) Every 60000 miles (96000 Replace spark plugs. km) * This is an optional feature. Operating in dusty or sandy conditions (such as unpaved or dusty roads) Inspect frequently, service as required * Replace cabin air filter. Replace engine air filter.
Scheduled Maintenance above 70°F (21°C) and at wide-open throttle for long periods above 45 mph (72 km/h), change non-synthetic rear axle fluid every 3000 miles (4800 kilometers) or three months, whichever comes first. This interval can be waived if the axle is filled with 75W140 synthetic gear fluid meeting Ford specification WSL-M2C192-A, part number F1TZ-19580-B, or equivalent. Add friction modifier XL-3 (EST-M2C118-A) or equivalent for complete refill of Traction-Lok rear axles.
Scheduled Maintenance SCHEDULED MAINTENANCE RECORD Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 355 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 356 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 357 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 358 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 359 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 360 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 361 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 362 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 363 Escape/Kuga (TM2), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I nf or mat i onPr ovi dedby: 364 Escape/Kuga (TM2), enUSA, First Printing
Appendices Description of Other Rights and Limitations END USER LICENSE AGREEMENT • VEHICLE SOFTWARE END USER LICENSE AGREEMENT (EULA) • • You (“You” or “Your” as applicable) have acquired a vehicle having several devices, including SYNC ® and various control modules, ("DEVICES") that include software licensed or owned by Ford Motor Company and its affiliates ("FORD MOTOR COMPANY").
Appendices • • • • Single EULA: The end user documentation for the DEVICES and related systems and services may contain multiple EULAs, such as multiple translations and/or multiple media versions (e.g., in the user documentation and in the software). Even if you receive multiple EULAs, you are licensed to use only one (1) copy of the SOFTWARE.
Appendices • • Links to Third Party Sites: The SOFTWARE may provide you with the ability to link to third party sites. The third party sites are not under the control of FORD MOTOR COMPANY, its affiliates and/or its designated agent.
Appendices TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, its affiliates, and third party software and service providers. General Operation • Voice Command Control: Certain functions within the SYNC® system may be accomplished using voice commands. Using voice commands while driving helps you to operate the system without removing your hands from the wheel or eyes from the road.
Appendices • • • Your Responsibilities and Assumptions of Risk • You agree to each of the following:(a) Any use of the SOFTWARE while driving an automobile or other vehicle in violation of applicable law or otherwise driving in an unsafe manner presents a significant risk of distracted driving and should not be attempted under any circumstances;(b) Use of the SOFTWARE at excessive volume poses a significant risk of hearing damage and should not be attempted under any circumstances;(c) The SOFTWARE may n
Appendices Disclaimer of Warranty CREATE A WARRANTY. SHOULD THE SOFTWARE, THIRD PARTY SOFTWARE, OR THIRD-PARTY SERVICES PROVE DEFECTIVE, YOU ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. SOME JURISDICTIONS DO NOT ALLOW THE DISCLAIMER OF IMPLIED WARRANTIES OR LIMITATIONS ON APPLICABLE STATUTORY RIGHTS OF A CONSUMER, SO THE ABOVE DISCLAIMER MAY NOT FULLY APPLY TO YOU.
Appendices the right to litigate (or participate in as a party or class member) all disputes in court before a judge or jury. Instead, all disputes will be resolved before a neutral arbitrator, whose decision will be final except for a limited right of appeal under the Federal Arbitration Act. Any court with jurisdiction over the parties may enforce the arbitrator’s award. Binding Arbitration and Class Action Waiver (a) Application.
Appendices may award the same damages to You individually as a court could. The arbitrator may award declaratory or injunctive relief only to You individually, and only to the extent required to satisfy Your individual claim. Arbitration fees and incentives. • • • (h) Claims or disputes must be filed within one year.
Appendices 3. Software License (a) observe all traffic laws and otherwise drive safely; • (b) use your own personal judgment while driving.
Appendices ii. violates any law, statute, ordinance or regulation, including but not limited to laws and regulations related to spamming, privacy, consumer and child protection, obscenity or defamation, or iii. is harmful, threatening, abusive, harassing, tortuous, defamatory, vulgar, obscene, libelous, or otherwise objectionable; and (f) lease, rent out, or otherwise permit unauthorized access by third parties to the TeleNav Software without advanced written permission of TeleNav. • 4.
Appendices REASON WHATSOEVER (INCLUDING, WITHOUT LIMITATION, ALL DAMAGES REFERENCED HEREIN AND ALL DIRECT OR GENERAL DAMAGES IN CONTRACT, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE), THE ENTIRE LIABILITY OF TELENAV AND OF ALL OF TELENAV'S SUPPLIERS SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE TELENAV SOFTWARE. SOME STATES AND/OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
Appendices 8.6 conferred by implication, statute, inducement, estoppel or otherwise, and TeleNav and its suppliers and licensors hereby reserve all of their respective rights other than the licenses explicitly granted in this Agreement. The headings in this Agreement are for convenience of reference only, will not be deemed to be a part of this Agreement, and will not be referred to in connection with the construction or interpretation of this Agreement.
Appendices HERE holds a non-exclusive license from the United States Postal Service® to publish and sell ZIP+4® information. positioning devices or any mobile or wireless-connected electronic or computer devices, including without limitation cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or PDAs. ©United States Postal Service® 2014. Prices are not established, controlled or approved by the United States Postal Service®.
Appendices Governing Law. The above terms and conditions shall be governed by the laws of the State of Illinois [insert “Netherlands” where European HERE Data is used], without giving effect to (i) its conflict of laws provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded.
Appendices If the Contracting Officer, federal government agency, or any federal official refuses to use the legend provided herein, the Contracting Officer, federal government agency, or any federal official must notify HERE prior to seeking additional or alternative rights in the Data. Gracenote Data shall also apply to such content and such content providers shall be entitled to all of the benefits and protections set forth herein that are available to Gracenote.
Appendices Gracenote uses a unique identifier to track queries for statistical purposes. The purpose of a randomly assigned numeric identifier is to allow Gracenote to count queries without knowing anything about who you are. For more information, see the web page at www.gracenote.com for the Gracenote Privacy Policy. OF THE GRACENOTE SOFTWARE OR ANY GRACENOTE SERVER.
Index 4 Audible Warnings and Indicators.............87 Automatic Transmission Warning Chime...................................................................87 Engine On Warning Chime................................87 Headlamps On Warning Chime......................87 Key in Ignition Warning Chime.........................87 Keyless Warning Alert ........................................87 Parking Brake On Warning Chime..................87 4WD See: Four-Wheel Drive.......................................
Index B Changing a Road Wheel...........................262 Dissimilar Spare Wheel and Tire Assembly Information.....................................................262 Tire Change Procedure....................................263 Blind Spot Information System..............162 Switching the System Off and On...............164 System Errors.......................................................164 Using the System................................................162 Changing the 12V Battery.................
Index Cross Traffic Alert.........................................164 Emission Control System..........................135 False Alerts............................................................167 Switching the System Off and On................167 System Errors.......................................................167 System Lights, Messages and Audible Alerts..................................................................166 System Limitations............................................
Index Exterior Mirrors................................................79 Gauges...............................................................83 Blind Spot Monitor..............................................80 Fold-Away Exterior Mirrors..............................80 Heated Exterior Mirrors......................................80 Integrated Blind Spot Mirrors..........................80 Memory Mirrors....................................................80 Power Exterior Mirrors..........................
Index Information Messages..................................91 Hints on Controlling the Interior Climate..........................................................103 Airbag........................................................................92 Alarm........................................................................92 Automatic Engine Shutdown..........................92 Battery and Charging System.........................93 Blind Spot Information and Cross Traffic Alert System.....................
Index K Manual Climate Control.............................101 Manual Liftgate..............................................59 Closing the Liftgate.............................................59 Opening the Liftgate...........................................59 Keyless Entry....................................................63 SECURICODE™ KEYLESS ENTRY KEYPAD..............................................................63 Manual Seats..................................................
Index Overhead Console........................................123 Rear View Camera P Rear Window Wiper and Washers...........72 See: Rear View Camera....................................158 Rear Window Washer.........................................73 Rear Window Wiper.............................................72 Parking Aids....................................................152 Recommended Towing Weights............180 Refueling..........................................................
Index Running Out of Fuel......................................131 Starting a Gasoline Engine........................125 Adding Fuel From a Portable Fuel Container...........................................................132 Filling a Portable Fuel Container...................132 Safety Belts.......................................................27 Automatic Engine Shutdown.........................126 Failure to Start.....................................................
Index U Tire Care..........................................................244 Glossary of Tire Terminology.........................245 Information About Uniform Tire Quality Grading.............................................................244 Information Contained on the Tire Sidewall...........................................................246 Temperature A B C............................................245 Traction AA A B C..............................................244 Treadwear.................
Index W Using Traction Control................................149 Switching the System Off...............................149 System Indicator Lights and Messages..........................................................149 Using a Switch.....................................................149 Using the Information Display Controls.............................................................149 Warning Lamps and Indicators................85 Airbag - Front...................................................