Installation Guide

ManualsBrandsFranke ManualsKitchenAxis 20-in x 20.5-in Silk Deck and Bowl Single Bowl Drop-In or Undermount 3-Hole Commercial/Residential Kitchen Sink

Congratulations!

You have purchased a quality product designed for long lasting beauty. The following instructions will take you step-

by-step through the installation process and care of your product. We recommend reading the entire instruction

booklet before beginning.

Caution: Risk of personal injury. Metal surfaces are sharp and can cause severe cuts. Use gloves and handle

sink and tools with care.

Installing Your New Sink

Tools And Materials

Step 1: Remove existing sink

1. Leave the faucet and drain outlet in place

2. Shut off water supply valves (usually under sink).

3. Release any water that may be in the supply lines by opening faucet valves

(the same way you would normally turn your water on). Let water run until it

4. Disconnect the supply lines from the water supply valves.

6. Remove clips around underside of old sink.

Topmount Installation Instructions:

Stainless Steel Sinks

KindredINST-TOPEZT 08/19

1. Drivers

3. Silicone Sealant or

Plumber’s Putty

2. 2” Hole Saw (if installing new countertop)

4. Adjustable

Wrench

9. Measuring

Tape

6. Drill

Jigsaw

5. Pipe Wrench (if steel pipe is used)

8. Gloves

10. Work Light

11. File

Supply valves

Waste trap

Supply

line

Step 1

#2 Robertson’s Bit

1/4” Nut Driver

Flat Head

Screwdriver

Summary of content (6 pages)

PAGE 1
USA Topmount Installation Instructions: Stainless Steel Sinks Congratulations! You have purchased a quality product designed for long lasting beauty. The following instructions will take you stepby-step through the installation process and care of your product. We recommend reading the entire instruction booklet before beginning. Caution: Risk of personal injury. Metal surfaces are sharp and can cause severe cuts. Use gloves and handle sink and tools with care.
PAGE 2
. Step 2 th Length Wid Step 2: OPTION A: Prepare existing countertop 1. Make sure existing countertop cut-out opening is the proper size. Set the new sink into opening. The sink rim should rest evenly on the countertop. Slight sawing. 3. OPTION B: Prepare a new countertop using the sink as a template 1. Carefully place the sink upside down on the countertop at the desired position. Trace the outline of the sink onto the countertop. Do not cut along this line. 2.
PAGE 3
5. Do not overtighten. It is only necessary to draw the rim down snugly to the countertop. 6. Wipe excess sealant from perimeter with a wet cloth. Step 6: Final Steps 1. Connect and tighten hot and cold faucet supply lines, strainer, drain and trap assembly. Note: Depending on the the new sink installation. 2. Turn on water supply and examine all connections for leaks. If leak appears, tighten joint slightly. Do not overtighten. 3. 4.
PAGE 4
USA Instrucciones de instalación del montaje superior: Fregaderos de acero inoxidable ¡Felicitaciones! Ha comprado un producto de calidad diseñado para brindar belleza duradera y muy fácil de instalar. Las instrucciones que aparecen a continuación le van a guiar paso a paso por el proceso de instalación y cuidado de su producto. Le sugerimos que lea todo el manual de instrucciones antes de seguir adelante. Precaución: graves. Utilice guantes y manipule el fregadero y las herramientas con cuidado.
PAGE 5
Paso 2 1. Largo Anc ho inconvenientes sobre la encimera. Para realizar ajustes leves, puede utilizar una lima o sierra de vaivén. 2. Utilice la lima o la sierra de vaivén con cuidado para no fragmentar ni quebrar la encimera. 3. fregadero de plantilla 1. Con cuidado, coloque el fregadero al revés sobre la encimera en la ubicación que desee. Marque el contorno del fregadero en la encimera. No realice el corte siguiendo esta línea. 2.
PAGE 6
1. drenaje debajo del fregadero para que se adapten al fregadero nuevo. 2. Abra el suministro de agua y controle que no existan pérdidas en ninguna de las conexiones. Si hay pérdidas, ajuste la unión levemente. No ajuste excesivamente. 3. Coloque el tapón y llene el fregadero para controlar que no existan pérdidas en el área debajo del fregadero y alrededor de la brida de drenaje. 4.