OWNER’S MANUAL Model No. GZFI8146.0 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (inside tower) QUESTIONS? At FreeMotion Fitness, we are committed to providing complete customer satisfaction. If you have questions, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Visit our website at www.freemotionfitness.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ADJUSTMENT . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the strength equipment. 1. Read all instructions in this manual before using the strength equipment. Use the strength equipment only as described in this manual. the strength equipment when it is in use. 9. All users of the strength equipment should be instructed to report any injury or strength equipment irregularity to facility staff immediately. 2.
WARNING DECAL PLACEMENT The decals shown below have been placed on the strength equipment in the indicated locations. If a decal is missing or illegible, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual and order a free replacement decal. Apply the decal in the location shown. Note: The decals may not be shown at actual size.
BEFORE YOU BEGIN Thank you for selecting the FREEMOTION® EPIC™ PRONE LEG CURL strength equipment. The strength equipment’s stylish ergonomic design and never-beforeseen features improve upon traditional strength training. The innovative features and quality construction provide a reliable product for your club. And the advanced solutions to isolating individual muscle groups make the PRONE LEG CURL strength equipment a key tool for members to reach their goals.
ADJUSTMENT This section explains how to adjust the strength equipment. Make sure all parts are properly tightened each time the strength equipment is used. Replace any worn parts immediately. ADJUSTING THE RESISTANCE To change the amount of resistance for your workout, insert the weight pin into the desired weight. Make sure that the weight pin is fully inserted into the weight.
MAINTENANCE AND TROUBLESHOOTING For optimal performance of the strength equipment and to reduce the chances of injury to users, you must perform preventive maintenance on a regular basis. Instruct all personnel to perform the procedures described in this section. Personnel must also record and report any accident. To maintain the strength equipment’s warranty, use only FREEMOTION EPIC parts for repair or replacement.
Cable Guards Check the cable guards to ensure that they are not rubbing against the cables and that they are holding the cables in the grooves of the pulleys. If a cable guard is not correctly aligned, loosen the bolt slightly, readjust the cable guard as necessary, and retighten the bolt. If there is too much tension on the cables, the top weight will not rest on the second weight, and it may be difficult to insert the weight pin into the weight plates.
CABLE DIAGRAM The cable diagram shows the proper route of the cable. Use the diagram to make sure that the cable and the cable guards have been assembled correctly. If the cable has not been correctly routed, the strength equipment will not function properly and damage may occur. The numbers show the correct route of the cable. Make sure that the cable guards do not touch or bind the cable. 4 5 Torque to 85 in./lbs. (9.
WEIGHT STACK SERVICING Servicing the weight stack involves replacing the two guide bushings and weight insert in the top weight. To order these parts, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. 1. Remove the wingnuts under the tower cap and remove the tower cap from the tower. 2. Remove the guide rod nuts and washers from the top of each guide rod. 3. Lift the coupler cover and loosen the four set screws—this will release the cable. 4. Lift the guide rods out of the top of the tower.
Top Weight Adjustment Tools required: 5/32” hex key “V” Pulley Adjustment Tools required: Adjustable wrench 1. If the cable needs to be shortened 3/4 in. (2 cm) or more, follow the instructions in steps 1 and 2 on page 8; then, go to step 2 below. 1. Lift the top weight off the weight stack and insert the weight pin into the second weight and the sixth hole from the top of the weight rod. 2. Lift the coupler cover from the top weight coupler.
NOTES 12
PART LIST—Model No. GZFI8146.0 R1106A If replacement parts are needed, or if parts are missing or damaged, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 1 1 1 1 1 1 19 1 2 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1 1 1 1 2 2 2 1 1 2 1 4 1 1 2 2 1 1 Description Key No. Qty.
EXPLODED DRAWING—Model No. GZFI8146.
EXPLODED DRAWING—Model No. GZFI8146.
HOW TO CONTACT CUSTOMER CARE If you have questions after reading this manual, or if you require assistance, please contact Customer Care at the address and phone number listed below. Please be prepared to give the following information: • the MODEL NUMBER of the product (GZFI8146.