Use and Care
Table Of Contents
- Table of contents
- Questions?
- Product Record and Registration
- Important Safety Instructions
- Cooking Recommendations
- Before Setting Surface Controls
- Radiant surface elements
- 1. Place correctly sized cookware on the radiant surface element.
- 2. Push in and turn the surface control knob in either direction (Figure 5) to the desired setting (refer to the “Suggested radiant surface element settings” table, Table 1).
- 3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.
- Suggested radiant surface element settings
- Home Canning
- Radiant surface elements
- Setting Surface Controls
- Before Setting Oven Controls
- 1. Press clock key.
- 2. Press in and hold or key until the correct time appears in the display. The UP arrow key will increase time and DOWN arrow key will decrease time.
- Operating oven light (some models)
- Setting bake
- Setting broil
- 1. Turn the oven control knob to broil. Most foods can be broiled at the broil setting. Preheat the oven if desired.
- 2. Place the insert on the broiler pan (if equipped), then place the food on the insert. Do not use the broiler pan without the insert or cover the insert with aluminum foil (Fig. 4). The exposed fat could ignite.
- 3. Place the broiler pan on the oven rack. Leave the oven door open at the broil stop position when broiling (Figure 13).
- 4. Broil on one side until food is browned; turn and broil on the second side. Season and serve.
- 5. When broiling is finished, turn the oven temp control knob to OFF
- Figure 11: Be sure to set oven control to broil.
- Figure 12: Broil rack positions and broil pan insert
- Figure 13: Open door to stop position when broiling
- Setting Oven Controls
- Figure 14: Use cleaners with caution
- Surface elements and drip bowls
- 1. Lift the edge of the drip bowl across from the terminal end. Lift the surface element and drip bowl together just enough to clear the cooktop.
- 2. While holding the drip bowl and surface element, gently pull the terminal end out from terminal plug. Do not remove the hold-down clip (if equipped) from the drip bowl.
- Figure 15: Removing coil and drip bowl
- Cleaning drip bowls
- 1. Slide the terminal end on the element through the opening in the drip bowl.
- 2. Align the element support to rest on the rim inside the drip bowl. If your drip bowl is equipped with a hold-down clip, align the element support opposite the terminal end with the slot in the hold-down clip, and snap into place.
- 3. After the element is positioned in the drip bowl, line up the terminal end with the terminal plug as shown.
- 4. Hold the surface element and drip bowl together as level as possible and firmly push the terminal end into the terminal plug. Make sure element terminal is seated properly into terminal plug. Make sure the surface element is level to reduce the ha...
- Cleaning under bake element (some models)
- Cleaning under cooktop (some models) To raise the cooktop for cleaning (some models)
- Removing and Replacing the Oven Door:
- 1. Open oven door completely, horizontal with floor (See Figure 18).
- 2. Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 19). A tool such as a small flat-blade screwdriver may be required.
- 3. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 20).
- 4. Close the door to approximately 10 degrees from the door frame (See Figure 20).
- 5. Lift the oven door hinge arms over the roller pins located on each side of the oven frame (See Figure 21).
- 1. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 20).
- 2. Holding the oven door at the same angle as the removal position, seat the hook of the hinge arm over the roller pins located on each side of the oven door frame (See Figure 20 and Figure 21). The hook of the hinge arms must be fully seated onto th...
- 3. Fully open the oven door, horizontal with floor (See Figure 18).
- 4. Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges to the locked position (See Figure 19).
- 5. Close the oven door.
- Figure 18: Door hinge location
- Figure 19: Door hinge locks
- Figure 20: Holding door for removal
- Figure 21: Replacement and location of hinge arm and roller pin
- Replacing the Oven Light
- To remove and replace storage drawer (some models)
- 1. Pull empty drawer out until it stops.
- 2. Tilt up the front of the drawer up and pull it out over the glide stop.
- 1. Insert the back of the drawer into the opening.
- 2. Lift up the drawer and line up the drawer supports with the rails. Make sure to clear the glide stop.
- 3. Push in the drawer until it stops.
- Figure 23: Parts of storage drawer
- Care and Cleaning
- Before You Call
3
Read all instructions before using this appliance.
This manual contains important safety symbols
and instructions. Please pay attention to these
symbols and follow all instructions given.
Do not attempt to install or operate your appliance
until you have read the safety precautions in this
manual. Safety items throughout this manual are
labeled with a WARNING or CAUTION statement
based on the risk type.
Warnings and important instructions appearing in
this guide are not meant to cover all possible
conditions and situations that may occur.
Common sense, caution, and care must be
exercised with installing, maintaining, or operating
your appliance.
DEFINITIONS
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol
to avoid possible injury or death.
Indicates a potentially hazardous situation
which, if not avoided, may result in death or
serious injury.
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
Indicates installation, operation, maintenance,
or valuable information that is not hazard
related.
Indicates a short, informal reference –
something written down to assist the memory or
for future reference.
WARNING
CAUTION
IMPORTANT
NOTE
WARNING
Tip Over Hazard
• A child or adult can tip
the range and be killed.
• Verify the anti-tip device
has been installed to floor
or wall.
• Ensure the anti-tip device is
re-engaged to floor or wall when the
range is moved.
• Do not operate the range without the
anti-tip device in place and engaged.
• Failure to follow these instructions can
result in death or serious burns to
children and adults.
Range
leveling
leg
Anti-tip
bracket
To check if the anti-tip bracket is installed
properly, use both arms to grasp the rear edge
of the range back. Carefully attempt to tilt
range forward. When properly installed, the
range should not tilt forward.
Refer to the anti-tip bracket installation instruc-
tions supplied with your range for proper
installation.
IMPORTANT SAFETY INSTRUCTIONS