Product Specifications Sheet
Accessories information available
on the web at frigidaire.com
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FFGW2415Q 12/16 © 2016 Electrolux Home Products, Inc.
Specifications
subject to change.
Single Wall Ovens
FFGW2415Q S/W/B 24" Gas
Single Wall Oven Specifications
•
Product Shipping Weight (approx.) – 150 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = .60 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @ 120V = 5 Amps
•
Always consult local and national electric and gas codes.
•
Oven ships with 3/4" factory regulator.
•
LP Gas convertible.
•
Do not obstruct flow of combustion air at oven vent nor around base
or beneath lower front panel of appliance. Oven requires fresh air for
proper burner combustion.
•
Oven vent location should be a minimum 36" height above floor.
•
Minimum 21-1/4" clearance for oven door depth when open.
•
Full oven base of solid plywood or similar material required, capable
of supporting 150 Lbs.
•
Base must be level and cabinet front must be square.
•
Single Wall Oven is NOT approved to be used in side-by-side
installation.
•
Single Wall Oven is NOT approved to be used alone in under-counter
installation or in combination with any Frigidaire® Warmer Drawer or
Built-In Microwave Oven.
Alternate Installations
•
Oven can also be installed into an existing two-cavity oven cutout
opening measuring 42-1/8" H x 22-1/2" W. To accommodate opening
for smaller oven, filler strips need to be installed vertically on each
side of opening along with two standard 2 x 4s (22" minimum length),
installed upright on each side beneath oven’s side rails, flush with
cabinet front. Two height adjusters, located on bottom sides of oven
wrapper, must also be lowered to raise oven by 1". Oven’s bottom
trim will then overlap cabinet face 1/4" minimum to hide opening at
bottom.
•
To accommodate existing 37-1/2" to 39" cutout height, oven’s height
adjusters must be lowered to raise oven by 1" in addition to bottom
trim’s 1/2" overhang allowing for a 1-1/2" total height adjustment.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Alternate Installation
Oven can also be installed into an existing two-cavity oven cutout
opening measuring 42
1
/8"
H x 22
1
/2"
W. To accommodate opening
for smaller oven, filler strips need to be installed vertically on each
side of opening along with two standard 2 x 4s (22" minimum length),
installed upright on each side beneath oven’s side rails, flush with
cabinet front. Two height adjusters, located on bottom sides of oven
wrapper, must also be lowered to raise oven by 1". Oven’s bottom trim
with then overlap cabinet face
1
/4" min. to hide opening at bottom.
To accommodate existing 37
1
/2" to 39" cutout height, oven’s height
adjusters can be lowered to raise oven by 1" in addition to bottom
trim’s
1
/2" overhang allowing for a 1
1
/2" total height adjustment.
24" Single Gas Wall Ovens_1-1/2 Cell
Frigidaire Baseline (models FFGW2415Q & FFGW2425Q)
24"
min.
1
1
/2"
min.
10
"
min.
27
1
/2"
max.
37
1
/2"
min.
38"
max.
22"
24"
min.
10"
min.
27
1
/2"
max.
2"min.
20"
1
1
/2" Dia.
hole for gas
hookup
7
5
/8"
C
L
Electrical
outlet
location
Full base
required to
support
150 lbs.
Bottom cutout
edge must be
finish cut
Hole for
electrical
cord
Height
adjuster
37
3
/8"
21
11
/16"
25
3
/8"
23
3
/8"
Power
supply
location
(left
bottom
rear)
38
7
/16"
23
7
/8"
Allow at
least 21
1
/4"
clearance for door
depth when open