Installation Instructions

Place the mounting plate against the wall and
insert the toggle wings into the h oles in th e wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure th e bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and th at the plate is properly
cen tered un der th e cabinet.
CAUTION: Be careful to avoid pinch in g fingers
between the back of the mounting plate and th e wall.
Tigh ten all bolts. Pull the plate away from th e wall
to h elp tighten th e bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
A1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the moun tin g plate
through th e holes design ated to go in to drywall
and reattach th e toggle wings to
3
⁄4″ ( 19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1. Attach Moun tin g Plate to Wall
A2. Prepare Top Cabinet
Mount Microwave O ven
A5.
Adjust Exhaust Adaptor
A6.
Wall
M ounting
Plate
Spacing for Toggles
M ore Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST (Vertical Duct)
A
IMPORTANT NOTES:
• Make sure th e screws for the
blower motor and blower plate
are securely tighten ed when
they are rein stalled. Th is will
help to preven t excessive
vibration.
• Make sure th e motor wiring has
been properly routed and secured,
and th at the wires are not pinch ed.
A7. Connect Ductwork
A3.
A4.
Check Damper O peration
Adapting Microwave Blower for
Outside Top Exhaust
EN-12
3/8"TO
EDGE
%#
76
+10Ä
+(':*#756
#&#
26
14+5215+6
+10
'&176
5+&'
4'%1/
/'0&'&&+/'05+10
)4'#
5'Ä.
#&'0#+49+..
&+5%*#
4)'+06
1*175'56
4
7%674'
/
+0+/7/9+&6*
4'37+4'&
4'#49#..6'/2.#6'
NO
TE
:
IT IS VERY I
MPORTANT TO
READ AND FO
LLOWTHE
D
IRECTIONS
IN THE INSTALLA
T
ION INSTRU
CTI
ON
S
BEFO
RE PR
O
CEEDINGWITH TH
IS
REAR WALL TEMPLA
TE.
This R
e
arWall Templ
a
te serves to po
sition th
e botto
m
mounting
pl
a
te
a
nd to loc
a
te th
e hor
izon
ta
l e
xhau
st
ou
tlet.
1
. Us
e a l
e
v
el
to
c
h
ec
k th
a
t the
t
emplate is
po
sit
ioned
ac
cura
tely.
2. L
o
c
ate
andmark a
t least o
nestud
on th
eleft or
r
ight
side of th
e c
enterl
in
e
.
016'
It is imp
o
rt
ant to use at least
one wo
od
sc
rew
mounted firmly in a s
tud
to suppor
t the w
eight
ofthe micro
w
a
ve. M
ar
k
two additional, even
lyspaced
locatio
n
s f
o
r the suppl
ied to
ggle bol
t
s.
3. Drill holes in the
marked location
s.
Where t
here is
a s
tud, drill a 3/16" hole
fo
r
wood sc
r
ews. F
or
h
oles
thatdo n
o
t lin
e up
with
a
stud, d
r
ill 5
/8" ho
les
fo
r
togg
le bolts.
016'
DO
NOT I
NSTALL THE MO
U
NTI
NG PL
ATE
AT
THIST
IME.
4. Re
move th
e te
mplate fromthe rea
r
wal
l.
5.Review the Installation Instruc
ti
on book
for y
ou
r
installatio
n situa
tion.
Locate and m
ar
k
holes to ali
gn with holes in t
he
mountingplate.
IMP
O
RTANT:
LOCA
T
E
AT LEA
ST ONE STUD
ON EI
T
HERSIDE
O
F
THE CENT
E
RLI
N
E
.
MARKT
HE LO
CATIONF
O
R 2 ADDITIONAL, EVENLY
SP
ACE
D T
OGGLE
BOLTS IN THE MOUNTING
PLATE
AREA
.
Locate and mar
k
holes to ali
gn with holes in t
he
mountingplate.
IMPORTANT
:
LO
C
A
T
E AT LEAST O
NESTUD
ON EI
THER SID
E
OF
TH
E
CENT
E
R
LIN
E
.
MARKTHE LOCATIO
N
F
O
R 2 ADDITIONAL, EV
ENL
Y
SP
ACED
TOGGLE BO
LTS IN THE MOUN
TING PLATE
AREA.
Trim the re
ar
wall tem
plat
e along
the do
tted line.
Trim the rear wall tem
plate along
the dotted line.
%
(%76176(14*14+<106#.
1765+&'':*#756
%7
6
*1.
'6
*417)*4'#49#.
.
(14
':*#756#&#26
14
12"
4"
Da
rle
vu
elt
a
ala ho
j
apar
a
co
ns
ul
t
arla
v
er
si
ó
n
e
n
Espa
ñol.
IMPORTANT :Do not remove the cardboard
etween the heat shield and door.
spacers b