Installation Instructions

INSTALLATION OVERVIEW
C1. Attach Moun tin g Plate to Wall
C2. Prepare Top Cabinet
C4.
C5.
Mount the Microwave Oven
IMPORTANT NOTES:
• Make sure th e screws for th e blower motor and blower
plate are securely tighten ed when th ey are rein stalled.
This will help to prevent excessive vibration.
• Make sure th e motor wiring has been properly routed
and secured, and that the wires are n ot pinch ed.
Installation Instructions
Place the mounting plate against the wall and
insert the toggle wings into the h oles in th e wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure th e bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
cen tered un der th e cabinet.
CAUTION: Be careful to avoid pinch in g fingers
between the back of the mounting plate and th e wall.
Tigh ten all bolts. Pull the plate away from th e wall
to h elp tighten th e bolts.
4
3
ATTACH THE MOUNTING
PLATE TO THE WALL
C1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the moun tin g plate through
the holes designated to go in to drywall and
reattach the toggle win gs to
3
⁄4″ (19 mm) onto
each bolt.
1
Wall
M ounting
Plate
Spacing for Toggles
M ore Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
RECIRCULATING (Non-Vented Ductless)
C
Install or change Charcoal Filter
C3. Check Blower Plate
NOTE:
CabinetCabinet
If the cabinet depth including the cabinet doors
is more than 13""'' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/ intake.
o
EN-20
3/8"T
OE
DGE
%#76+
10
Ä

+(
':*#
756

#&#261
4+52
1
5
+6+10'
&1
765
+&'
4
'%
1//'0
&'
&
&+/'0
5
+1
0)
4'#5'Ä.
#&
'
0#+4
9+..




&+5
%*#4
)
'
+06
1*1
7
5
'

5647%674'

/+0+/7/9
+&6*4
'37+
4'&
4'#49#..6'/2.#6'
NOTE:IT IS VERY IMP
OR
TANT T
O
READ AN
D FOLLOWTHE DIRECTIONS
IN
THE INST
ALLAT
ION
I
NS
TRUCTIONS
B
E
F
O
R
E PROCEEDING
W
IT
H T
HIS
RE
AR W
A
LL TEMPL
A
T
E
.
Th
is RearWall
Te
mp
late se
rves toposi
tion
th
e bo
tto
m
mounting
plateand to
lo
cateth
e
horiz
ont
al
exhaust
o
utle
t.
1.Usea level t
o
c
he
ck tha
t t
he
te
mp
la
te is
p
ositioned
accurately.
2.
L
o
ca
te a
n
d mark
a
t
least o
nestud on
th
e left o
r
r
ig
ht
si
de
ofthecenterline
.
016
'

It
is
i
mportantto u
se at l
e
astone
w
ood
screwmo
u
nted firm
ly in
a
stud
tosu
pp
ort t
he
weight
of t
he
microwave.Marktwo a
dditio
n
a
l,
e
ve
n
lyspaced
lo
cationsfo
r the supp
li
ed
to
gg
le b
o
lts.
3.
Dri
ll h
oles in
th
e
marke
d lo
ca
tions.Where thereis
a s
tu
d
,d
rill
a
3
/16"h
ol
efor
wo
od
screws.
Fo
r
holes
th
a
tdo no
t
lin
e up
with a
stud
, d
rill5
/8"ho
le
s
for
tog
g
le bo
lt
s.
016
'

DO N
O
TINS
TALL THEMOUNTING
PL
A
TE
ATTH
IS TIME.
4. Rem
ove the template
from
t
he
re
a
r wall.
5. Re
view
th
e Insta
lla
tion
In
st
ru
ction
b
ook fo
r
yo
ur
in
st
allation
situa
tion.
Loc
a
teand
ma
rk holes to al
ign with holes in th
e
mount
i
ng pl
ate.
I
MPORTANT:
LOCA
T
E AT
LEAST ONESTUD ON E
ITHER SIDEOF
T
HE
CENTE
RL
I
NE.
MARK T
HELOCA
T
ION FOR2
ADDITIONAL,
EVEN
LY
SPACE
D TO
G
GLE BO
LTS
IN TH
E
MO
UN
T
ING
PLATE
AREA.
Loc
a
te andmark holes t
o
al
i
gn
wi
t
h
hol
es
inthe
m
oun
tin
g p
late.
IMPOR
TA
NT
:
LO
CAT
E
AT LE
A
ST
O
NEST
UD
ON EITHE
R SIDE O
F
T
HE
CE
NT
E
RLIN
E.
MARK T
H
E
LOCATION F
O
R2 A
D
DIT
IONAL
, EVENLY
SPA
CED TOGGLE BO
LTSIN
TH
E
MOUNT
INGPLATE
A
REA.
T
rim the rear w
a
ll t
em
p
late alon
g
t
he dott
edline.
Trim th
e rear w
alltem
plate a
l
ong
t
hed
otted
line.
%
(%76176(14*
14+<106#.
1765+&'':*#756
%76
*1
.
'
6*4
17
)
*
4'
#
49#..
(14'
:*#756#&#
2
6
1
4
1
2
"
4
"
Da
r
levuel
ta
a
laho
ja
paraconsu
ltar
la
v
e
r
sióne
n
Es
pa
ño
l.
IMPORTANT :Do not remove the cardboard
etween the heat shield and door.spacers b