Wiring Diagram

NOTICE - This service data sheet is intended for use by persons having electrical
and mechanical training and a level of knowledge of these subjects generally
considered acceptable in the appliance repair trade. The manufacturer cannot
be responsible, nor assume any liability for injury or damage of any kind arising
from the use of this data sheet.
SAFE SERVICING PRACTICES
To avoid the possibility of personal injury and/or property damage, it is important
that safe servicing practices be observed. The following are examples, but without
limitation, of such practices.
1. Before servicing or moving an appliance remove power cord from electrical outlet,
trip circuit breaker to OFF, or remove fuse.
2. Never interfere with the proper installation of any safety device.
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
p/n A00498604 Rev B (1603)
3. GROUNDING: The standard color coding for safety ground wires is GREEN or
GREEN WITH YELLOW STRIPES. Ground leads are not to be used as current
carrying conductors. It is extremely important that the service technician
reestablish all safety grounds prior to completion of service. Failure to do
so will create a potential safety hazard.
4. Prior to returning the product to service, ensure that:
 •Allelectricconnectionsarecorrectandsecure.
 •Allelectricalleadsareproperlydressedandsecuredawayfromsharpedges,
high-temperature components, and moving parts.
 •Alluninsulatedelectricalterminals,connectors,heaters,etc.areadequately
spaced away from all metal parts and panels.
 •Allsafetygrounds(bothinternalandexternal)arecorrectlyandsecurely
reassembled.
Indicated % Power Notes
0 0 Off
Lo 7 Keep Warm
1.5 9 -
2 12 -
2.5 15 -
3 17 -
3.5 18 -
4 19 -
4.5 20 -
5 21 -
5.5 25 -
6 31 -
6.5 38 -
7 45 -
7.5 50
8 54 -
8.5 59
9 64 -
9.5 80
Hi 100
Pb 138-152 PowerBoost
Electronic Surface Element Control (ESEC)
ThiscooktopisequippedwithanElectronicSurfaceElement
Control(ESEC),whichpreciselycontrolsthesmoothtopcooking
elements at multiple settings. For the user, the elements are
operated by the knobs. The control settings are shown in 2-digit
displays.
Hot Surface display message - If any of the induction elements
arehot,thehotsurfacemessage(HE)willdisplayandremain
ON until the cooktop cools.
Replacing an induction element
Whenever replacing any induction element use only the screws
supplied with the range to secure the element to the mounting
panel. Never use any other type of screw to attach the induction
element.
* Please note: Electronic boards are very sensitive to static
electricity. Static electricity can permanently damage electronic
boards. Before handling these parts, be sure to drain static elec-
tricity from your body by properly grounding yourself.
BC3 TO USER INTERFACE BOARD
Á PLAQUETTE D'INTERFACE DE UTILISATEUR
THERMAL CUT-OUT
COUPE-CIRCUIT THERMIQUE
GENERATOR/POWERBOARD-LEFT (1)
CARTE GENERATEUR-GAUCHE (1)
GENERATOR/POWERBOARD-CENTER (2)
CARTE GENERATEUR-CENTRE (2)
BC3
B81 BC4 B71
TAB1 TAB2
BC1
TAB102 TAB101
BC5
BPL1 BPL2 BPN2 BPN1
BPE03
BC3 B81 BC4 B71
TAB1 TAB2
BC1
TAB102 TAB101
BC5
BPL1 BPL2 BPN2 BPN1
BPE03
THERMAL CUT-OUT
COUPE-CIRCUIT THERMIQUE
THERMAL CUT-OUT
COUPE-CIRCUIT THERMIQU
E
GENERATOR/POWERBOARD-RIGHT (3)
CARTE GENERATEUR-DROIT (3)
BC3
B81 BC4 B71
TAB1 TAB2
BC1
TAB102 TAB101
BC5
BPL1 BPL2 BPN2 BPN1
BPE03
ID JUMPER: ADDRESS 1
DO NOT CONNECT BC1
IDENTIFICATEUR: ADRESSE 2
NE PAS BRANCHER BC1
ID JUMPER: ADDRESS 2 DO NOT CON-
NECT BLACK JUMPER TO BC5 OR BC1
IDENTIFICATEUR: ADRESSE 2
NE PAS BRANCHEZ EN UTILISANT
FAISCEAU-FIL NOIR BC5 OU BC1
ID JUMPER: ADDRESS 3
CONNECT RED JUMPER TO BC1
IDENTIFICATEUR: ADRESSE 2
BRANCHEZ EN UTILISANT
FAISCEAU-FIL ROUGE BC1
SERVICE DATA SHEET
36” INDUCTION COOKTOP