Use and Care Guide

ManualsBrandsFrigidaire ManualsAppliance partsTop Mount Refrigerator Built-In White Plastic Ice Maker Kit

P/N: 5304520541

WARNING

• To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical

power before connecting a water supply line to the refrigerator.

• Connect the ice maker to a potable water supply only.

AUTOMATIC ICE MAKER

Use & Care Manual

An authorized service technician is recommended to install the ice maker kit.

Ice Maker (IM117000) Kit Components

5304520536

Ice Maker

QTY: 1

5304520542

Shoulder

Screw QTY: 5

5304520538/5304520539

Housing with Door QTY:

5304520535

Ice Container

QTY: 1

5304520537

Bracket (30” only)

QTY: 1

Mounting Features

Parts needed for install inside the unit

Tools Needed:

• Flat head screw driver • Phillips or Quadrex driver

• ¼” Hex driver • Gloves

• Drill • Needle nose pliers

Parts needed for install on back side of the unit

5304520540

Water Valve

QTY: 1

218990901

Clip (30” only)

QTY: 2

218976923

Tube

QTY: 1

241500304

#8 screw

QTY: 2

218515401

Water Valve

Harness Clip

(30” only)

QTY: 1



NOTE

Check with your local building authority for recommendations on water lines and associated materials prior to installing your

new refrigerator. For household water line hookup from the home water supply system to the unit, Frigidaire recommends

for homes with existing valves its Smart Choice

water line kit 5304437642 (with a 6 ft. Stainless Steel Water Line) and for

homes without an existing valve, Frigidaire recommends its Smart Choice

water line kit 5304493869 (with a 6’ Polyline

Waterline). Please refer to www.frigidaire.com/Filters--Accessories/Refrigerator-Accessories for more information.

Summary of content (8 pages)

PAGE 1
AUTOMATIC ICE MAKER Use & Care Manual An authorized service technician is recommended to install the ice maker kit. WARNING • To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. • Connect the ice maker to a potable water supply only.
PAGE 2
Ice Maker Installation Instructions 5. For 30” wide refrigerator install bracket onto ice maker. Ice maker will slide onto mounting features on bracket and snap into place. The locking feature is located on the rear of the ice maker. 1. Unplug refrigerator from electrical outlet. 2. Lift the freezer shelf up and out. Set aside. 2 1 Locking Feature 3.
PAGE 3
Ice Maker Installation Instructions 7. Install ice maker housing onto shoulder screws on the top of the unit until it locks into place with a snap. 11. Install the 2 water line clips on the unit evenly spaced inside the depressed area located under the water inlet. Insert the water line tube into the clips. Water Inlet Water Line Clip 8. To install the ice bucket, the freezer shelf needs to be in the lowest position.
PAGE 4
Ice Maker Installation Instructions (with access cover) 15. Plug connector on water valve wire harness into the connector at top of appliance compartment. Install the water valve clip at the bottom right side of the unit, and route and attach the water valve harness into the clip. CAUTION Wear gloves and use extreme CAUTION when handling the access cover. 12. Remove 8 screws from access cover located at the bottom rear outside of the unit. Set aside. 16.
PAGE 5
Ice Maker Installation Instructions (without access cover) 21. Connect the valve wire harness with the AC connector. Insert the wiring in the box as shown. Close the box cover completely, ensuring all wiring is inside. 19. Remove the connector box from the unit with a Philips screwdriver. 22. Plug the water tube from the unit into the bottom outlet of the water valve. The tube should be pushed into the valve up to the black line marked in the tube. 20.
PAGE 6
Connecting Ice Maker to Water Supply Before Installing The Water Supply Line, You Will Need: WARNING • Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips screwdriver To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. • Access to a household cold water line with water pressure between 30 and 100 psi. CAUTION • A water supply line made of ¼ in. (6.
PAGE 7
Connecting Ice Maker to Water Supply To Connect Water Supply Line To Ice Maker Inlet Valve 5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown. 1. Disconnect refrigerator from electric power source. 6. Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface. 2. Place end of water supply line into sink or bucket.
PAGE 8
Ice Service If your refrigerator has an automatic ice maker, minimal ice will be produced during the first 24 hours of operation. Air in new plumbing lines may cause the ice maker to cycle 2 or 3 times before making a full tray of ice. With no usage, it will take approximately 1 to 2 days to fill the ice container. IMPORTANT To ensure proper function for your ice maker, hook up water supply immediately or turn ice maker OFF.