SPARC® Enterprise T5120 and T5220 Servers Installation Guide Manual Code : C120-E462-01EN Part No.
Copyright 2007 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. FUJITSU LIMITED provided technical input and review on portions of this material. Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in this document, and such products, technology and this document are protected by copyright laws, patents and other intellectual property laws and international treaties.
Copyright 2007 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, Etats-Unis. Tous droits réservés. Entrée et revue tecnical fournies par FUJITSU LIMITED sur des parties de ce matériel. Sun Microsystems, Inc. et Fujitsu Limited détiennent et contrôlent toutes deux des droits de propriété intellectuelle relatifs aux produits et technologies décrits dans ce document.
Contents Preface 1. xiii Preparing for Installation 1 Tools and Equipment Needed 3 Optional Component Installation ESD Precautions 3 4 Installation Overview 4 Cabling Notes for Both Servers 6 Port Locations for Both Servers Slide Rail Assembly Notes for Both Servers 10 Cable Management Notes for Both Servers 13 Safety Precautions 2.
Connecting the Server Cables for Both Servers Connector Locations 32 ▼ To Connect the Service Processor Serial Management Port ▼ To Connect the Service Processor Network Management Port ▼ To Connect the Ethernet Network Cables TTYA Serial Port USB Ports ▼ ▼ 35 36 36 37 37 To Connect the AC Power Cable to the Server Managing Cables With the CMA Powering On the System 38 38 Securing the Server Cables in the CMA Dismounting the Servers 3.
▼ To Perform a Normal System Initialization Booting the Solaris Operating System To Boot the Solaris Operating System ▼ To Reset the System ▼ To Power Cycle the System Updating the Firmware 61 Updating the Firmware 61 ▼ B. 57 59 59 60 To Update the Firmware Selecting a Boot Device ▼ C. 57 ▼ Verifying System Functionality A.
viii SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
Figures FIGURE 1-1 SPARC Enterprise T5120 Server 2 FIGURE 1-2 SPARC Enterprise T5220 Server 2 FIGURE 1-3 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5120 Server FIGURE 1-4 Front Panel USB Ports on the SPARC Enterprise T5120 Server FIGURE 1-5 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5220 Server FIGURE 1-6 Front Panel USB Ports on the SPARC Enterprise T5220 Server FIGURE 1-7 Sections of the Slide Rail Assembly on the SPARC Enterprise T5220 Server FIGURE
FIGURE 2-12 Unlocking the Slide Rail Assembly (Either Server) FIGURE 2-13 Rail Mounting Bracket Release Button (Either Server) FIGURE 2-14 Rear Panel Connectors on the SPARC Enterprise T5120 Server 33 FIGURE 2-15 Front Panel USB Ports on the SPARC Enterprise T5220 Server 33 FIGURE 2-16 Rear Panel Features on the SPARC Enterprise T5220 Server FIGURE 2-17 Front Panel USB Ports on the SPARC Enterprise T5220 Server FIGURE 2-18 Service Processor Serial Management Port – Rear Panel FIGURE 2-19 Se
Tables TABLE 1-1 Ethernet Connection Transfer Rates 7 TABLE 3-1 Disk Slot Numbers, Logical Device Names, and Physical Device Names TABLE 3-2 Device Identifiers and Devices 56 56 xi
xii SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
Preface The SPARC Enterprise T5120 and T5220 Servers Installation Guide provides instructions, background information, and reference material to help you install SPARC® Enterprise T5120 and T5220 servers. The installation instructions in this document assume that a system administrator is experienced with the Solaris™ Operating System (Solaris OS). Note – All internal components except hard drives must be installed by qualified service technicians only.
Structure and Contents of This Manual This manual is organized as described below: ■ CHAPTER 1 Preparing for Installation Provides an installation overview for the servers. ■ CHAPTER 2 Installing the SPARC Enterprise T5120 and T5220 Servers Provides instructions for installing the servers into a rack. ■ CHAPTER 3 Powering On the System Provides instructions for configuring and powering on the servers and for installing additional software.
Shipping Kit Inventory List for Both Servers Standard components of the SPARC Enterprise T5120 and T5220 are installed at the factory. However, if you ordered options such as PCI cards or a monitor, these are shipped to you separately. Note – Inspect the shipping cartons for evidence of physical damage. If a shipping carton appears damaged, request that the carrier’s agent be present when the carton is opened. Keep all contents and packing material for the agent’s inspection.
Related Documentation The latest versions of all the SPARC Enterprise Series manuals are available at the following Web sites: Global Site http://www.fujitsu.com/sparcenterprise/manual/ Japanese Site http://primeserver.fujitsu.
Using UNIX Commands This document might not contain information about basic UNIX® commands and procedures such as shutting down the system, booting the system, and configuring devices. Refer to the following for this information: ■ Software documentation that you received with your system ■ Solaris™ Operating System documentation, which is at: http://docs.sun.com Text Conventions This manual uses the following fonts and symbols to express specific types of information.
Prompt Notations The following prompt notations are used in this manual. Shell Prompt Notations C shell machine-name% C shell superuser machine-name# Bourne shell and Korn shell $ Bourne shell and Korn shell and Korn shell superuser # Conventions for Alert Messages This manual uses the following conventions to show alert messages, which are intended to prevent injury to the user or bystanders as well as property damage, and important messages that are useful to the user.
Alert messages in the text An alert message in the text consists of a signal indicating an alert level followed by an alert statement. Alert messages are indented to distinguish them from regular text. Also, a space of one line precedes and follows an alert statement. Caution – The following tasks regarding this product and the optional products provided from Fujitsu should only be performed by a certified service engineer. Users must not perform these tasks.
Notes on Safety Important Alert Messages This manual provides the following important alert signals: Caution – This indicates a hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This signal also indicates that damage to the product or other property may occur if the user does not perform the procedure correctly.
Product Handling Maintenance Warning – Certain tasks in this manual should only be performed by a certified service engineer. User must not perform these tasks. Incorrect operation of these tasks may cause electric shock, injury, or fire.
Alert Labels The followings are labels attached to this product: ■ Never peel off the labels. ■ The following labels provide information to the users of this product. Example: SPARC Enterprise T5220 Fujitsu Welcomes Your Comments We would appreciate your comments and suggestions to improve this document. You can submit your comments by using "Reader's Comment Form".
■ Reader's Comment Form Preface xxiii
FOLD AND TAPE NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO 741 SUNNYVALE CA POSTAGE WILL BE PAID BY ADDRESSEE FUJITSU COMPUTER SYSTEMS AT TENTION ENGINEERING OPS M/S 249 1250 EAST ARQUES AVENUE P O BOX 3470 SUNNYVALE CA 94088-3470 FOLD AND TAPE xxiv SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
CHAPTER 1 Preparing for Installation This chapter provides background information about both the servers installation procedures that are provided in Chapter 2.
2 FIGURE 1-1 SPARC Enterprise T5120 Server FIGURE 1-2 SPARC Enterprise T5220 Server SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
Tools and Equipment Needed To install the system, you must have the following tools: ■ No. 2 Phillips screwdriver ■ ESD mat and grounding strap In addition, you must provide a system console device, such as one of the following: ■ ASCII terminal ■ Workstation ■ Terminal server ■ Patch panel connected to a terminal server Optional Component Installation The standard components of the server are installed at the factory.
ESD Precautions Electronic equipment is susceptible to damage by static electricity. Use a grounded antistatic wriststrap, footstrap, or equivalent safety equipment to prevent electrostatic damage (ESD) when you install or service the servers.
Note – In the rest of this manual, the term rack means either an open rack or a closed cabinet. 5. Connect the server to a serial terminal or a terminal emulator (PC or workstation) to display system messages. See “Powering On the System for the First Time” on page 41. Tip – The serial terminal or a terminal emulator should be connected before you connect the power cables. As soon as AC power is connected to the system, the service processor immediately powers on and runs diagnostics.
11. Power on the server from a keyboard using the ILOM software. See “To Power On the System” on page 53. 12. Configure the Solaris OS. See “Booting the Solaris Operating System” on page 57. The Solaris OS is preinstalled on the servers. When you power on, you are automatically guided through the Solaris OS configuration procedure. 13. Install any required patches to the server. Refer to the SPARC Enterprise T5120 and T5220 Server Product Notes for a list of required patches. 14.
■ Ethernet ports are labeled NET0, NET1, NET2, and NET3. The Ethernet interfaces operate at 10 Mbps, 100 Mbps, and 1000 Mbps. The transfer rates for the Ethernet ports are given in TABLE 1-1. TABLE 1-1 Ethernet Connection Transfer Rates Connection Type IEEE Terminology Transfer Rate Ethernet 10BASE-T 10 Mbit/sec Fast Ethernet 100BASE-TX 100 Mbits/sec Gigabit Ethernet 1000BASE-T 1000 Mbit/sec ■ TTYA serial port: Use the DB-9 connector with a null modem cable for serial devices.
FIGURE 1-3 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5120 Server 15 1 2 3 4 5 6 7 8 16 9 17 10 11 12 13 14 Figure Legend 1 Power Supply 0 10 Gbit Enet Port NET2 2 Power Supply 1 11 Gbit Enet Port NET3 3 Locator LED Button 12 USB Port 0 4 Service Required LED 13 USB Port 1 5 Power OK LED 14 TTYA Serial Port 6 Service Processor Serial Management Port 15 PCIe/XAUI Slot 0 7 Service Processor Network Management Port 16 PCIe/XAUI Slot 1 8 Gbit En
Figure Legend 5 Hard Drive HDD3 6 USB Port 2 7 USB Port 3 See FIGURE 1-5 and FIGURE 1-6 for the locations of the ports on the SPARC Enterprise T5220 server.
FIGURE 1-6 Front Panel USB Ports on the SPARC Enterprise T5220 Server 1 2 3 4 5 6 7 8 9 10 11 Figure Legend 1 System Status Indicators: Top to bottom: Power Button, Power OK LED, Service Required LED, Locator LED Button 2 Hard Drive HDD0 3 Hard Drive HDD1 4 Hard Drive HDD2 5 Hard Drive HDD3 6 Hard Drive HDD4 7 Hard Drive HDD5 8 Hard Drive HDD6 9 Hard Drive HDD7 10 USB Port 2 11 USB Port 3 Slide Rail Assembly Notes for Both Servers The rackmount kit has two slide rail asse
Each slide rail assembly consists of a three-section slide rail and a removeable mounting bracket (FIGURE 1-7). FIGURE 1-7 Sections of the Slide Rail Assembly on the SPARC Enterprise T5220 Server 1 2 3 4 Figure Legend 1 Mounting bracket 2 Front section 3 Middle section 4 Rear section ■ The front, middle, and rear sections form the slide rail. The middle and rear sections have holes for mounting screws and adjust to fit rack depths from 24 in. (61 cm) to 36.5 in. (93 cm).
FIGURE 1-8 12 Locating the Locks on the Slide Rail Assembly for the SPARC Enterprise T5220 Server SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
Cable Management Notes for Both Servers The same cable management arm (CMA) is included with the rackmounting kit for each server (FIGURE 1-9). The CMA clips onto the slide rails. Use the velcro straps to secure cabling to the CMA.
Safety Precautions Caution – Deploy the antitilt bar on the equipment rack before beginning an installation. Caution – The SPARC Enterprise T5220 server weighs approximately 46 lb (20.7 kg). Two people are required to lift and mount this 2U server into a rack enclosure when using the procedures in this document. Caution – When completing a two-person procedure, always communicate your intentions clearly before, during, and after each step to minimize confusion.
CHAPTER 2 Installing the SPARC Enterprise T5120 and T5220 Servers This chapter provides instructions for installing the servers into an equipment rack. Note – If your rackmount kit came with its own instructions, use the instructions in your rackmount kit instead of the instructions in this chapter. After performing the SPARC Enterprise T5120 and T5220 installation, proceed to Chapter 3 for first-time power on.
Installing the Servers in a Rack Note – Ensure that you have all of the parts in the rackmount kit before you begin the installation of the server. See “Shipping Kit Inventory List for Both Servers” on page xv. Note – The procedures in this chapter are the same for both the 1U and 2U servers. The illustrations show a 2U server only as an example. The rackmount kit (same for both 1U and 2U servers) contains two slide rail assemblies, which can be installed on either the right or left side of the rack.
FIGURE 2-1 Unlocking the Slide Rail Assembly (Either Server) b. Pull the mounting bracket out until it locks in the extended position. c. Slide the mounting bracket release button in the direction shown in FIGURE 2-2, then slide the mounting bracket out of the slide rail.
FIGURE 2-2 Location of the Mounting Bracket Release Button (Either Server) d. Press the metal lever (labeled Push) on the middle section (FIGURE 2-3) of the sliding rail, then push the middle section back into the rack.
FIGURE 2-3 Unlocking the Slide Rail Middle Section (Either Server) Metal lever 2. Attach a mounting bracket to the right side of the chassis. a. Position the mounting bracket against the chassis (FIGURE 2-4) so that the slide rail lock is at the front and the three keyed openings on the mounting bracket are aligned with the three locating pins on the side of the chassis.
FIGURE 2-4 Attaching a Mounting Bracket to the Chassis (Either Server) b. With the heads of the locating pins protruding though the keyed openings in the mounting bracket, pull the mounting bracket toward the front of the chassis until the bracket locks into place with an audible click. c. Verify that all locating pins are trapped in the keyed openings and that the correct locating pin has engaged the mounting bracket lock, as shown in the right side of FIGURE 2-4. 3.
5. Determine which screws you will use to mount the slide rails. If your rack has threaded mounting holes in the rack posts, determine whether the threads are metric or standard. Select the appropriate screws from the package included in the mounting kit. If your rack does not have threaded mounting holes, the mounting screws are secured with a caged nut. 6. Attach a slide rail to the right front rack post. a.
c. Loosely attach the rear of the slide rail to the rear rack post with two screws. 7. Attach the second slide rail to the left rack posts in a similar manner. Do not tighten the screws. 8. Use the slide rail spacing tool to adjust the distance between the slide rails. a. At the front of the rack, plug the left side of the tool into slots at the end of the left rail (FIGURE 2-6). FIGURE 2-6 Using the Slide Rail Spacing Tool to Adjust the Distance Between the Slide Rails (Either Server) b.
d. Tighten the screws to lock the ends of the rails in place. e. At the rear of the rack, repeat Step a through Step d. for the rear ends of the rails. ▼ To Insert and Lock the Server in the Rack 1. Deploy the antitilt bar, if the chassis or rack is so equipped. Caution – The weight of the servers on extended slide rails can be enough to overturn an equipment rack. Caution – The 2U server weighs approximately 46 lb (20.7 kg).
FIGURE 2-7 Mounting the Chassis on the Slide Rails (Either Server) 3. Slide the chassis into the rack. Caution – Before continuing, verify that the server is securely mounted in the rack, and that the slide rails are locked to the mounting brackets.
Installing the Cable Management Arm for Both Servers The rack mounting kit for each server comes with the same cable management arm (CMA) assembly. The CMA installation and cable management procedures are the same for both servers. Note – The CMA includes velcro straps to secure the cables inside the CMA. Do not install the velcro straps until you install the CMA, connect the cables, and place the cabling inside the CMA as described in the following procedures.
FIGURE 2-8 Inserting the CMA Rail Extension Into the Rear of the Left Slide Rail (Either Server) The right sides of the two CMA arms have hinged extensions. On the manufacturer’s instruction sheet, the smaller extension is called the CMA Connector for Inner Member. It attaches to the right mounting bracket. The larger extension is called the CMA Connector for Outer Member, and attaches to the right sliding rail.
3. Insert the smaller extension into the clip located at the end of the mounting bracket (FIGURE 2-9). Slide the smaller extension into the square hole on the middle-in-width of the clip located at the end of the mounting bracket.
4. Insert the larger extension into the end of the right sliding rail (FIGURE 2-10).
5. Insert the hinged plastic connector at the left side of the CMA fully into the CMA rail extension (FIGURE 2-11). The plastic tab on the CMA rail extension locks the hinged plastic connector in place.
▼ To Verify the Operation of the Slide Rails and the CMA Tip – Two people are needed for this procedure: one to move the server in and out of the rack, and one to observe the cables and CMA. 1. For a free-standing rack, deploy the antitilt bar. 2. Unlock the slide lock buttons (FIGURE 2-12) at the right and left sides of the chassis. 3. Slowly pull the server out of the rack until the slide rails reach their stops. FIGURE 2-12 Unlocking the Slide Rail Assembly (Either Server) 4.
7. Pull both slide rail release buttons toward you simultaneously and slide the server back into the rack (FIGURE 2-13). The server should slide smoothly into the rack without binding. FIGURE 2-13 Rail Mounting Bracket Release Button (Either Server) 8. Verify that the CMA retracted without binding. 9. Adjust the cable straps and CMA as required to secure the cables. See “Managing Cables With the CMA” on page 38.
Connecting the Server Cables for Both Servers To boot the server, you must connect and configure the network and serial ports. The procedures are given in the following sections.
FIGURE 2-14 1 Rear Panel Connectors on the SPARC Enterprise T5120 Server 2 3 4 5 6 7 8 9 10 11 12 13 14 Figure Legend 1 Power Supply 0 8 NET0 2 Power Supply 1 9 NET1 3 Locator LED Button 10 NET2 4 Service Required LED 11 NET3 5 Power OK LED 12 USB Port 0 6 Service Processor Serial Management Port 13 USB Port 1 7 Service Processor Network Management Port 14 TTYA Serial Port USB ports 2 and 3 are located on the front panel (FIGURE 2-15).
FIGURE 2-16 1 Rear Panel Features on the SPARC Enterprise T5220 Server 2 3 4 5 6 7 8 9 10 8 NET0 11 12 13 14 Figure Legend 1 Power Supply 0 2 Power Supply 1 9 NET1 3 Locator LED Button 10 NET2 NET3 4 Service Required LED 11 5 Power OK LED 12 USB Port 0 6 Service Processor Serial Management Port 13 USB Port 1 7 Service Processor Network Management Port 14 TTYA Serial Port USB ports 2 and 3 are located on the front panel (FIGURE 2-17).
Figure Legend 4 Locator LED Button 5 USB Port 2 6 USB Port 3 ▼ To Connect the Service Processor Serial Management Port The service processor serial management port is marked SER MGT (FIGURE 2-18). It is the leftmost RJ-45 port on the rear panel. Note – The cable and DB-9 RJ-45 adapters are for the host serial port, and not for the server SER MGT port. FIGURE 2-18 Service Processor Serial Management Port – Rear Panel Use this port for server management.
▼ To Connect the Service Processor Network Management Port The service processor network management port is labeled NET MGT (FIGURE 2-19). It is located just to the right of the serial management (SER MGT) port on the rear panel. FIGURE 2-19 Service Processor Network Management Port – Rear Panel Note – This port is not operational until you configure the network settings (through the serial managment port), as detailed in “To Configure the Service Processor Network Management Port” on page 48.
FIGURE 2-20 Service Processor Ethernet Network Ports – Rear Panel 1. Connect a Category 5 cable from your network switch or hub to Ethernet Port 0 (NET0) on the rear of the chassis. NET0 is the farthest left port in the 4-port network cluster in FIGURE 2-20. 2. Connect Category 5 cables from your network switch or hub to the remaining Ethernet ports (NET1, NET2, NET3), as needed.
▼ To Connect the AC Power Cable to the Server Powering on the system for the first time requires special preparation and procedures. For example, if you have not prepared a display before connecting the AC power cable, system messages might be lost. Caution – Finish the hardware procedures in this chapter, but do not attach the AC power cable yet. Powering on the system for the first time requires special preparation and procedures.
FIGURE 2-21 Securing the Server Cables With the CMA and Velcro Straps (Either Server) Caution – Verify the operation of the slide rails and CMA, and cable service loops. Perform the steps in the following procedure again before continuing: “To Verify the Operation of the Slide Rails and the CMA” on page 30. Dismounting the Servers To install or replace internal parts in the server, you must first remove the server from the rack.
40 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
CHAPTER 3 Powering On the System This chapter includes instructions for booting the servers and for enabling the service processor network management port.
Note – To see these status and error messages, connect a terminal or terminal emulator to the serial management port (SERIAL MGT). For a basic procedure to connect a terminal or terminal emulator, see “To Power On the System for the First Time” on page 43. For a more detailed discussion on configuring the system console and connecting terminals, refer to the SPARC Enterprise T5120 and T5220 Server Administration Guide.
compatability CLI as the default CLI (role=administrator, cli=alom). For more information on using the ALOM compatability CLI, refer to the Integrated Lights Out Manager 2.0 Supplement for SPARC Enterprise T5120 and T5220 Servers. ▼ To Power On the System for the First Time Tip – The serial terminal or a terminal emulator should be connected before you connect the power cables, or you will not see the system messages.
FIGURE 3-1 Rear Panel Power Connectors of a SPARC Enterprise T5120 Server 1 2 Figure Legend 1 Power Supply 0 2 Power Supply 1 FIGURE 3-2 Rear Panel Power Connectors of a SPARC Enterprise T5220 Server 1 2 Figure Legend 1 Power Supply 1 2 Power Supply 0 After the service processor boots, the service processor login prompt is displayed on the serial console. The following example shows a partial output from the service processor boot sequence leading to the login prompt.
CODE EXAMPLE 3-1 Sample Service Processor Output (Continued) fsck 1.37 (21-Mar-2005) Setting kernel variables ... ... done. Mounting local filesystems... Cleaning /tmp /var/run /var/lock. Identifying DOC Device Type(G3/G4/H3) ... OK Configuring network interfaces...Internet Systems Consortium DHCP Client V3.0.1 Copyright 2007 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/products/DHCP eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
Enabling the Service Processor Network Management Port The service processor network management port is not operational until you configure network settings for the service processor. Configure the service processor in this order: 1. After the service processor boots, access the ILOM CLI through the serial management port. See “To Log Into the Service Processor Using the Serial Management Port” on page 47. 2. Configure the service processor.
▼ To Log Into the Service Processor Using the Serial Management Port After the service processor boots, access the ILOM CLI to configure and manage the system. The ILOM CLI prompt (->) is displayed at the first time the service processor is booted. The default configuration provides an ILOM CLI root user account. The default root password is changeme. Change the password using the service processor ILOM CLI password command. 1.
2. Enter root for the login name followed by your password. ... hostname login: root Password: password (nothing displayed) Waiting for daemons to initialize... Daemons ready Sun(TM) Integrated Lights Out Manager Version 2.0.0.0 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.
■ /SP/network pendingipgateway – IP address of the gateway for the subnet ■ /SP/network pendingipnetmask – Netmask for the service processor subnet ■ /SP/network pindingipdiscovery - Specifies whether the service processor uses DHCP or static IP address assignment ■ /SP/network commitpending - Commits the service processor to use the pending settings Configure these parameters with the set command.
5. If you choose to use a static IP configuration, set the parameters pendingipdiscovery, pendingipaddress, pendingipgateway, and pendingipnetmask as follows. a. Set the service processor to accept a static IP address. -> set /SP/network pendingipdiscovery=static Set 'pendingipdiscovery' to 'static' b. Set the IP address for the service processor. -> set /SP/network pendingipaddress=service-processor-IPaddr Set 'pendingipaddress' to 'service-processor-IPaddr' c.
CODE EXAMPLE 3-2 show /SP/network Command Output pendingipdiscovery = static pendingipgateway = xx.x.xx.x pendingipnetmask = 255.255.255.0 state = enabled Commands: cd set show -> Note – After setting the configuration parameters, you must enter the set /SP/network commitpending=true command for the new values to take affect. 7. Commit the changes to the service processor network parameters.
The service processor resets, runs diagnostics, and returns to the login prompt. ... hostname login: root Password: password (nothing displayed) Waiting for daemons to initialize... Daemons ready Sun(TM) Integrated Lights Out Manager Version 2.0.0.0 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.
● Open an SSH session and connect to the service processor by specifying its network address. % ssh root@xx.xxx.xx.x ... Are you sure you want to continue connecting (yes/no)? yes ... Password: password (nothing displayed) Waiting for daemons to initialize... Daemons ready Sun(TM) Integrated Lights Out Manager Version 2.0.0.0 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.
b. To initiate the power on sequence, type the start /SYS command. You will see an ILOM CLI alert message on the system console. This indicates that the system has reset. -> start /SYS Are you sure you want to start /SYS (y/n)? y Starting /SYS -> c. Switch to the system console to view POST output. -> start /SP/console Watch the POST output for possible fault messages. The following output is a sign that POST did not detect any faults: . . . 0:0>POST Passed all devices.
▼ To Connect to the System Console Output from POST, OpenBoot, and the Solaris OS is displayed in the system console using the network console on the service processor. ● Type the start /SP/console command. Multiple users can be connected to the console, but only one can be attached. -> start /SP/console Are you sure you want to start /SP/console (y/n)? y Serial console started. To stop, type #.
/pci@7c0/pci@0: Device /pci@7c0/pci@0: Device /pci@7c0/pci@0: Device /pci@7c0/pci@0: Device Probing I/O buses c d e f Nothing Nothing Nothing Nothing there there there there SPARC Enterprise T5220, No Keyboard ... {0} ok To understand the various devices and their path names as represented in the OpenBoot device tree, refer to TABLE 3-1 for disks and TABLE 3-2 for optional PCI cards.
Booting the Solaris Operating System The Solaris OS is preinstalled on the servers on the disk in slot 0. The Solaris OS is not configured (that is, the sys-unconfig command was run in the factory). If you boot the system from this disk, you will be prompted to configure the Solaris OS for your environment. ▼ To Boot the Solaris Operating System 1. At the ok prompt, boot from the disk that contains the Solaris OS. ■ If you know which disk to boot from, skip this step and perform Step 2.
starting rpc services: rpcbind keyserv ypbind done. Setting netmask of lo0 to 255.0.0.0 Setting netmask of bge0 to 255.255.255.0 Setting default IPv4 interface for multicast: add net 224.0/4: gateway xxxx syslog service starting. volume management starting. Creating new rsa public/private host key pair Creating new dsa public/private host key pair The system is ready. hostname console login: In the following example, the system is being booted from disk 0 (zero) on a SPARC Enterprise T5220 server.
Creating new dsa public/private host key pair The system is ready. wgs94-181 console login: ▼ To Reset the System ● If it is necessary to reset the system, use the shutdown -g0 -i6 -y command. # shutdown -g0 -i6 -y It is not necessary to power the system off and on to simply reset the system. ▼ To Power Cycle the System If a simple reset does not clear a system problem, you can power the system off and on with this procedure. 1. Shut down the Solaris OS.
3. Using the ILOM CLI, type the stop /SYS command to perform a graceful shutdown of the system. -> stop /SYS Are you sure you want to stop /SYS (y/n)? y Stopping /SYS -> Note – To perform an immediate and ungraceful shutdown, use the stop -force -script /SYS or stop -script /SYS commands. These commands stop everything immediately, ensure that all data is saved before entering these commands. 4. Type the start /SYS command.
APPENDIX A Updating the Firmware The flashupdate command updates both the service processor firmware and the server firmware. The flash image consists of the following components: ■ Service Processor firmware ■ OpenBoot ■ POST ■ Reset/Config ■ Sequencer ■ Partition description Updating the Firmware To use the features and fixes in subsequent firmware releases, perform “To Update the Firmware” on page 61. ▼ To Update the Firmware 1.
2. Open an SSH session to connect to the service processor. % ssh root@xx.xxx.xx.x ... Are you sure you want to continue connecting (yes/no)? yes ... Password: password (nothing displayed) Waiting for daemons to initialize... Daemons ready Sun(TM) Integrated Lights Out Manager Version 2.0.0.0 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. -> 3. Verify that the host is powered off. If the host is not powered off, type the stop /SYS command. -> stop /SYS 4.
■ -source – Specifies the IP address and full path name (URI) to the flash image -> load -source tftp://xxx.xxx.xx.xx/pathname NOTE: A firmware upgrade will cause the server and ILOM to be reset. It is recommended that a clean shutdown of the server be done prior to the upgrade procedure. An upgrade takes about 6 minutes to complete. ILOM will enter a special mode to load new firmware. No other tasks can be performed in ILOM until the firmware upgrade is complete and ILOM is reset.
CODE EXAMPLE A-1 Typical Boot Sequence Following Firmware Update (Continued) Configuring network interfaces...Internet Systems Consortium DHCP Client V3.0.1 Copyright 2007 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/products/DHCP eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX. Listening on LPF/eth0/00:14:4f:3f:8c:af Sending on LPF/eth0/00:14:4f:3f:8c:af Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.
APPENDIX B Selecting a Boot Device The boot device is specified by the setting of an OpenBoot configuration variable called boot-device. The default setting of this variable is disk net. Because of this setting, the firmware first attempts to boot from the system hard drive, and if that fails, from the on-board NET0 Gigabit Ethernet interface. This procedure assumes that you are familiar with the OpenBoot firmware and that you know how to enter the OpenBoot environment.
■ disk3 – Specifies internal drive 3 ■ net, net0, net1, net2, net3 – Specifies the network interfaces ■ full path name – Specifies the device or network interface by its full path name Note – The Solaris OS modifies the boot-device variable to its full path name, not the alias name. If you choose a nondefault boot-device variable, the Solaris OS specifies the full device path of the boot device. Note – You can specify the name of the program to be booted as well as the way the boot program operates.
APPENDIX C Installing the Servers With the Express Rail Rackmounting Kit This appendix provides instructions for installing the servers in an equipment rack with Express (snap-in) rails. The Express rail rackmounting kit installs quickly and does not require mounting screws or nuts. The kit and the installation procedures are the same for both the SPARC Enterprise T5120 and T5220 servers.
Slide Rail Assembly Notes for the Express Rail Rackmounting Kit The Express rail rackmount kit has two slide rail assemblies. A slide rail assembly can be installed on either the right or left side of the rack. Each slide rail assembly consists of a three-section slide rail and a removeable mounting bracket (FIGURE C-1).
■ The removeable mounting bracket slides 14.5 in. (37 cm) out of the slide rail, then locks in place. If you unlock the mounting bracket at this point, it slides an additional 14.5 in. (37 cm) before separating from the slide rail. You can then mount the mounting bracket to the right or left side of the server chassis. ■ Note that there are a total of six locks (FIGURE C-2) in a slide rail assembly. Four are on the mounting bracket. Two locks are on the slide rail.
FIGURE C-2 70 Locating the Locks on the Slide Rail Assembly for the SPARC Enterprise T5220 Server SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
Installing the Servers in a Rack With Express Rails Note – Ensure that you have all of the parts in the rackmount kit before you begin the installation of the server. See “Shipping Kit Inventory List for Both Servers” on page xv. The rackmount kit contains two slide rail assemblies, which can be installed on either the right or left side of the rack. A slide rail assembly consists of two parts: a slide rail and a removeable mounting bracket. The slide rail attaches to the rack posts.
FIGURE C-3 Unlocking the Express Rail Slide Rail Assembly b. Pull the mounting bracket out until it stops.
c. Slide the mounting bracket release button to the left (FIGURE C-4), then slide the mounting bracket completely out of the slide rail.
2. Attach a mounting bracket to the right side of the server chassis. a. Position the mounting bracket against the chassis (FIGURE C-5) so that the slide rail lock is at the front and the keyed openings on the mounting bracket are aligned with the locating pins on the side of the chassis. FIGURE C-5 Attaching an Express Rail Mounting Bracket to the Chassis b.
4. Orient slide rails and ensure that the ball bearing tracks (labeled FRONT) are forward (FIGURE C-6).
5. Extend the slide rails (outer section) to fit the rack and attach the slide rails to the rack (FIGURE C-7). You hear an audible click when the rails securely attach to the rack. FIGURE C-7 Attaching Express Slide Rails to the Rack Caution – Deploy the antitilt feature on the rack before continuing the installation. ▼ To Insert and Lock the Server in the Rack 1. Deploy the antitilt feature, if the rack is so equipped.
Caution – The weight of the servers on extended slide rails can be enough to overturn an equipment rack. Caution – The 2U server weighs approximately 46 lb (20.7 kg). Two people are required to lift and mount the server into a rack enclosure when using the procedures in this chapter. 2. Insert the ends of the mounting brackets into the sliding rails (FIGURE C-8). 3. Slide the server approximately halfway into the chassis (FIGURE C-8).
4. Slide the green release tab (FIGURE C-9). 5. Push the server all the way into the the rack until it locks into place (FIGURE C-9). FIGURE C-9 Sliding the Express Rail Release Tab and Securing the Server in the Rack Caution – Before continuing, verify that the server is securely mounted in the rack, and that the slide rails are locked in the mounting brackets.
Installing the Cable Management Arm The rackmounting kit for each server comes with the same cable management arm (CMA) assembly. The CMA installation procedures are the same for both servers. See “Installing the Cable Management Arm for Both Servers” on page 25. Connecting the Server Cables To boot the server, you must connect and configure the network and serial ports. For instructions, see “Connecting the Server Cables for Both Servers” on page 32.
80 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007
Index Symbols D #. escape sequence for system console, 59 DB-9 TTY connector, 7 definitions, See terms, 15 deinstallation of server, 39, 79 diagnostics, when run, 43 A accessing ILOM command line, 46 adapters for serial cables, 35 address, IP, 4 addresses, web, See web sites admin login, setting password for, 47 E enabling the network management port, 46 escape sequence #.
installation instructions, optional components, reference, 3 installing mounting brackets, 71 installing optional components, 3 inventory list, xv IP address, 4 L LEDs, ports, and slots illustrated, 7, 8 left and right sides defined, 15 levers, locking, See "slide rail assembly locks" locating pins for mounting brackets, 71 locations of ports, slots, and LEDs (illustration), 7, 8 locks, See "slide rail assembly locks" logging into service processor using network management port, 46, 52 using serial managem
spacing tool for slide rails, 22 Standby mode, 38 standby voltage causes service processor to power on, 5 standby voltage, 3.3v, 43 stop bit, 43 system console escape sequence #.
84 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007