AssemblyInstructions For more information contact our team: service.ec@foagroup.com CM7315Q/CM7315EK ASSEMBLYRATING Tools Required For Assembly: The Assembly Rating is a 5-point system that Allen Wrench shows the degree of effort needed in assembling a specific product (with 1 being Wrench easy and 5 being difficult). For some products,two persons are recommended.
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY. PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES When lock or spring washer is used inPosition each part correctly and insert Use cardboard or carpet area when an assembly, please make sure the screws or bolts into their respective assembling furniture to prevent lock or spring washer is placed holes by hand tighten or using the scratches.
Before you begin, please read Page 2 of "Assembly and Care Advice". And remember, do not tighten until each step is completed or instructed.
Hardware List Parts List #9 x 1pc Slat Center Support #I x 8pcs Nut Ø5/16" #10 x 2pcs Dusty Panel #J x 8pcs Screw #4 x 15mm #1 #10 #10 #2R #5 #6 #9 #4 #8 #2L #3 #4 #7 Page4 of 8
2) Align HB legs (#2R/L) to the holes of the headboard (#1), then secure by using bolts (#A) with washers (#B,C). #A x 12pcs #B x 12pcs #C x 12pcs #D 1) Align HB support (#5) to the holes of the HB legs (#2R/L), #A #B then secure by using bolts (#A) with washers (#B,C). #2R #D #A #B #C #C #5 #2L #1 1) Use a small amount of force to pull the drawers out from the footboard (#3). #3 #7 2) Attach support legs (#7) to the holes of the footboard (#3).
Align slat center support (#9) to the holes of the slat kit (#6), then secure by using screws (#E). #E x 5pcs #E #6 #9 Attach slat support legs (#8) to the holes of the slat center support (#9). Adjust the leveler of the support legs (#8) according to ground level.
Attach threaded studs (#F) to the holes of the headboard (#1) and footboard (#3), then align side rails (#4) to the threaded studs (#F) of the headboard (#1) and footboard (#3). Secure by using washers (#I) and hex nuts (#G). #1 #F x 8pcs #G x 8pcs #I x 8pcs #F #I #4 #G #H #4 #3 Align slats to the side rails, then secure by using screws (#E). #E x 10pcs #E Insert drawers back into footboard.
Place dusty panels (#11) to the bed frame, then secure by using screws (#J).
AssemblyInstructions For more information contact our team: service.ec@foagroup.com CM7315CK ASSEMBLYRATING Tools Required For Assembly: The Assembly Rating is a 5-point system that Allen Wrench shows the degree of effort needed in assembling a specific product (with 1 being Wrench easy and 5 being difficult). For some products,two persons are recommended.
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY. PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES When lock or spring washer is used inPosition each part correctly and insert Use cardboard or carpet area when an assembly, please make sure the screws or bolts into their respective assembling furniture to prevent lock or spring washer is placed holes by hand tighten or using the scratches.
Before you begin, please read Page 2 of "Assembly and Care Advice". And remember, do not tighten until each step is completed or instructed.
Hardware List Parts List #9 x 1pc Slat Center Support #I x 8pcs Nut Ø5/16" #10 x 2pcs Top Bed Rail #K x 12pcs Bolt Ø1/4" x 1-1/2" #11 x 2pcs Dusty Panel #L x 12pcs Lock Washer Ø1/4" #N x 8pcs Screw #4 x 15mm #M x 12pcs Flat WasherØ1/4" #1 #11 #11 #2R #5 #2L #6 #9 #4 #8 #10 #3 #4 #7 Page4 of 8
2) Align HB legs (#2R/L) to the holes of the headboard (#1), then secure by using bolts (#A) with washers (#B,C). #D #A #B #C #A x 12pcs #B x 12pcs #C x 12pcs #A #B #C #2R #D #5 1) Align HB support (#5) to the holes of the HB legs (#2R/L), then secure by using bolts (#A) with washers (#B,C). #2L #1 1) Use a small amount of force to pull the drawers out from the footboard (#3). #3 #7 2) Attach support legs (#7) to the holes of the footboard (#3).
Align slat center support (#9) to the holes of the slat kit (#6), then secure by using screws (#E). #E #E x 5pcs #6 #9 Attach slat support legs (#8) to the holes of the slat center support (#9). Adjust the leveler of the support legs (#8) according to ground level.
#1 #F #F x 8pcs #G x 8pcs #I x 8pcs #G #I #4 #H #4 Attach threaded studs (#F) to the holes of the headboard (#1) and footboard (#3), then align side rails (#4) to the threaded studs (#F) of the headboard (#1) and footboard (#3). Secure by using washers (#I) and hex nuts (#G). #3 Align slats to the side rails, then secure by using screws (#E). #E x 10pcs #E Insert drawers back into footboard.
Place dusty panels (#11) to the bed frame, then secure by using screws (#N). #N #N x 8pcs Align top bed rails (#10) to wash side rails, then secure by using bolts (#K) with washers (#L,M).
